Use Linksys E2000 Router As A Access Point?
Mar 13, 2012How can i use Linksys E2000 rounter as a Access point ?
View 1 Replies
ADVERTISEMENT
Linksys Wireless Router :: Using An E2000 As Repeater / Access Point?
Aug 3, 2011We have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?
View 3 Replies View RelatedLinksys Wireless Router :: E2000 Connected To RVS4000 As Access Point
Feb 26, 2012I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
Linksys Wireless Router :: E2000 - Configuring Second One As Repeater Access Point
May 28, 2011I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies View RelatedLinksys Wireless Router :: Turning E2000 Into Access Point / Switch?
Dec 6, 2012we got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?
View 2 Replies View RelatedHow To Configure Linksys E2000 As Access Point
Mar 25, 2011i have just connected my linksys e2000 to the internet now i would like to set it up so other computers can connect to the internet through it wired/ wireless
View 1 Replies View RelatedLinksys Access Point :: Add Repeater To E2000 System?
Mar 31, 2011I need to extend the wireless range over what I have using an E2000. Can I use a WAP610N in repeater mode? If not can I use a WAP54G knowing that there will be a performance loss? Is there another option to add additional coverage to the existing wireless network?
View 2 Replies View RelatedLinksys Wireless Router :: E2000 - Access Restriction Shuts Down Access To All Computer
Jan 1, 2013I have set up access restriction times for my son (we have wireless access for all systems). I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times
Linksys Wireless Router :: Internet Access Regarding Linksys E2000
Aug 21, 2011I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedLinksys Wireless Router :: Can't Access Internet Through E2000
Apr 21, 2013I have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
Linksys Wireless Router :: Cannot Access Website Through E2000
Nov 12, 2011I got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies View RelatedLinksys Wireless Router :: E2000 - Unable To Access Web Setup
May 12, 2012Just a day or two ago I was able to do what the title says, didn't make any adjustments to my E2000 while in it, had to find something though.Anyhow, connecting to http://192.168.1.1 results in "Unable to Connect", etc. Also tried it in IE9, Firefox Beta is my primary, and it still didn't work. Tried using Cisco Connect and it says it cannot connect to my router. I am wired to my E2000, which in turn is wired to my DSL modem (Actiontec GT701D-Its firewall not in use). I sitll have full connection to the internet as well as other wireless deveices do in my house.
View 1 Replies View RelatedLinksys Wireless Router :: Enable Guest Access On E2000?
Feb 12, 2013How do I reenable guest access on my e2000 without having cisco connect installed?
View 1 Replies View RelatedLinksys Wireless Router :: E2000 Not Allowing Access To Other Devices
Nov 5, 2011I just set up my e2000 on a PC using Windows 7. I am additionally trying to set up additional devices on the network. The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
I can't get these on the network through the e2000. They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security. What do I need to do to successfully put the above devices on the network?
Linksys Wireless Router :: E2000 Block All Internet Access?
Mar 12, 2012E2000 about a years old.One of the rule is to block internet access from 1am to 4am for certain internal IPs.Working fine until a week ago. Once the time kick in, the E2000 will not route any internet access for any internal IP until the unit is power off and power on reboot.If that rule is disabled. then the E2000 will route all days and nights with no problem.Updated firmware to 1.0.0.4 already.I replaced the WRT45 because of the same problem a year ago. Now just about a year, this E2000 keeps blocking all traffic.
View 1 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
Linksys Wireless Router :: E2000 / Remote Desktop Access With Mac And Asus Transformer Prime?
Jul 31, 2011I have an E2000 router with the most current firmware. I have a Sony VAio laptop with Windows 7 Home Premium 64bit,a Macbook with 10.6.8, and a new Asus Transformer Prime with ICS.My work desktop is a Dell Optiplex 380 with Windows 7 Pro 32bit. I frequently work from home and have no issues remoting into to my work PC from by Sony laptop via VPN and RDP.However I have never been able to connect successfully to my work PC with my Macbook(using Remote Desktop Connection 2.1 for Mac OS) or Asus tablet(using WYSE Pocket Cloud RDP app for Android). I can however connect to the VPN itself on the Macbook and tablet without issue same as my Windows laptop. The other interesting part is I can connect via RDP when I am connected to a Mi-Fi 3g hotspot. So it is definitely something in the my Linksys E2000 blocking the connection for some reason. I have even set Port forwarding of 3389 with the ip's of both the Macbook and Asus tablet.I have also tried connecting via ethernet to the router with the same outcome. I cannot ping my work pc from either device as well.In addition the firewall on my work PC is completely disabled and all services related to Remote desktop access are enabled and running.
View 3 Replies View RelatedLinksys Wireless Router :: E2000 Internet Access Is Not Affected When Printer Appears To Be Offline
Jun 10, 2011I've got a Linksys E2000 router and a Brother MFC-7840W wireless printer and they don't seem to want to play nice together. The set-up process was fine and I can usually print wireless without a problem, but every so often I'll try to print and my computer will say that the printer is offline. Other computers on my network also show it as offline. The printer confirms it has an IP address, but even after power cycling it won't be picked up by my machines. I've even tried a full reset of the printer and re-configured it, at which point it is able to successfully obtain an IP address, but it still shows as offline on my PCs.
The only solution I have found is to powercycle the router. This always works. Now that's not a terribly inconvenient workaround most of the time, so I've been doing that for a few months now. It obviously implicates the router as the point of failure, but wireless internet access is not affected when the printer appears to be offline, so obviously some packets are getting through normally.
Linksys Access Point :: WAP54G Access Point Setup After A Reset?
Jul 9, 2006I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedLinksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point
Jan 17, 2013I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedLinksys Access Point :: WRT320N Access Point Vs Range Extender
Dec 14, 2011Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedLinksys Access Point :: WAP4410n MIBs Or OIDs For Access Point
Jul 3, 2012I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Linksys Access Point :: Repeat WAP54G Access Point?
Aug 25, 2011What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedLinksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Linksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedLinksys Access Point :: E3000 Configuration As Access Point?
Apr 6, 2011I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedLinksys Access Point :: Way To Find Mib For WAP54G Access Point?
Feb 10, 2012I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedUsing A Linksys Router As An Access Point?
Oct 8, 2011Can i use linksys as an access point?
View 1 Replies View RelatedUsing 2nd Linksys Router As Access Point?
Jun 6, 2011I have two routers, one is NETGEAR with the MACINTOSH computer and the other is LINKSYS wireless G...what I want to do is make the the LINKSYS router an access point for my network and need to know how to do so.
View 1 Replies View RelatedLinksys WRT54GL Router - Access Point Causes Lag?
Jun 9, 2011In our house we use a Linksys WRT54GL router. When I am connected to the router via a cable I can play an online RPG without any problems.I recently connected an acecss point to the router ( a belkin N1 ). Even if I am connected with a cable to the accesspoint, which is connected to the router by cable as well, I get huge lag spikes about every 10 seconds while playing the game.
View 10 Replies View RelatedSetting Up Linksys Router As Access Point?
Mar 21, 2011i have a verizon usb720 modem. i want to set up my wirless printer. Previously i had this set up by a profesional. I bought a new computer and am now trying to set this up. I have a linksys router as well wrt54g how is tis done. you cannot connect anything to the modem but i have read that you can turn the router into an access point.
View 10 Replies View Related