Linksys Wireless Router :: E2000 Connected To RVS4000 As Access Point

Feb 26, 2012

I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1).  The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again..  I get the "NO INTERNET" prompt on the wireless....
 
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN,  I've determined that it's the E2000 that has disconnected from the RVS4000. 
 
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational.....  Until the next Power Failure....
 
Is there any way of making this Automatic.
 
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....

View 3 Replies


ADVERTISEMENT

Linksys Wireless Router :: Using An E2000 As Repeater / Access Point?

Aug 3, 2011

We have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?

View 3 Replies View Related

Linksys Wireless Router :: E2000 - Configuring Second One As Repeater Access Point

May 28, 2011

I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.

View 2 Replies View Related

Linksys Wireless Router :: Turning E2000 Into Access Point / Switch?

Dec 6, 2012

we got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?

View 2 Replies View Related

Use Linksys E2000 Router As A Access Point?

Mar 13, 2012

How can i use Linksys E2000 rounter as a Access point ?

View 1 Replies View Related

How To Configure Linksys E2000 As Access Point

Mar 25, 2011

i have just connected my linksys e2000 to the internet now i would like to set it up so other computers can connect to the internet through it wired/ wireless

View 1 Replies View Related

Linksys Access Point :: Add Repeater To E2000 System?

Mar 31, 2011

I need to extend the wireless range over what I have using an E2000. Can I use a WAP610N in repeater mode? If not can I use a WAP54G knowing that there will be a performance loss? Is there another option to add additional coverage to the existing wireless network?

View 2 Replies View Related

Linksys Wireless Router :: Names Of Devices Connected To E2000

Oct 18, 2010

How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.

View 9 Replies View Related

Linksys Wireless Router :: E2000 - Unable To Get Nanostation GUI When Connected

Feb 18, 2013

I am connected to my ISP via Nanostation 5 IP Add:192.168.10.186 S.M: 255.255.255.0, the Nanostation Lan cable is connected to the WAN port of my Linksys E2000, I am using a PPOE connection with my ISP, the Linksys broadcast a new network using DHCP service, The broadcasted Network is 192.168.5.X 255.255.255.0, the thing is i am unable to get the Nanostation GUI, when i replace the Linksys with a TP-Link router i have no such problem becuase in TP-Link i can add an additional IP address which is the Nanostation's IP,Is there any way i can get the Nanostation GUI?

View 3 Replies View Related

Linksys Wireless Router :: E2000 - PS3 Error / Ethernet Cable Is Not Connected

Nov 19, 2011

Problem: My PS3 displays An Ethernet cable is not connected almost immediately after logging in. I am connected through a Linksys E2000 router.  If I reset the cable modem, it will work for 10-15 minutes until it errors out again.  If I plug the PS3 directly into the cable modem, it works fine. I'm really confused. I do not believe it is the router, as my computer is also connected to the router, and works fine. My Touchpad is connected wirelessly and also works fine. I do not believe it is the PS3, because it works fine if I plug it directly into the cable modem. I tried switching to wireless and it finds a lot of other signals (including mine), but I have the same problem if I choose wireless.I first had this problem with a launch PS3 and a Netgear router after almost three years of no problems.

View 8 Replies View Related

Linksys Access Point :: WAP610N No Devices Connected To Wireless

Jul 21, 2011

I have a big house so I have a e4200 on one end of the house upstairs and the WAP610n on the other end downstairs linked via CA6.  I am having no issues with Laptops etc..just with Apple devices.  I spent a lot of time with chat support (waste of time).  WAP was flashed with latest firmware via hard wire no devices connected to wireless, has same ssid and security settings as router running on 2.4 ghz wpa2 personal AES.  I am using 2.4 due to iphone4 does not support 5ghz and wap does not support dual band (another bummer). I am using AES instead of TKIP/AES mixed mode due to apple devices will not acquire dhcp with this setting and if they do they lose it right away.  I have tried everything imaginable with the settings even changed beacon to 75, 50 RTS to 2304 etc...the current setting are the only ones that seem to work the best however when i run speedtest.net LA server or SD server the performance is horrible.  On windows laptop i can achieve 27mbps down 2.5mbpsup, my apple devices use to achieve very close numbers to that on a simple configuration with two Dlink DGL-4300's one as router one as AP (G mode).  So two major issues i have noticed is WAP610N has issues passing DHCP to apple devices and has extremely poor performance.  So my question is will there be a firmware to correct this issue or a new hardware version that i can exchange this for if I RMA it or would it be best to call it a day and just get a E3200 and use it as a real simultaneous dual band AP???

View 9 Replies View Related

Linksys Wireless Router :: E2000 Software Can't Find Sonos When Pc Is Connected Through Wifi

Aug 28, 2011

I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
 
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?

View 2 Replies View Related

Linksys Wireless Router :: E2000 - Access Restriction Shuts Down Access To All Computer

Jan 1, 2013

I have set up access restriction times for my son (we have wireless access for all systems).  I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
 
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
 
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times

View 3 Replies View Related

Linksys Wireless Router :: Can't Access Internet Through E2000

Apr 21, 2013

I have a Linksys E2000.
 
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.

View 4 Replies View Related

Linksys Wireless Router :: Cannot Access Website Through E2000

Nov 12, 2011

I got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.

View 2 Replies View Related

Linksys Access Point :: View Connected Devices On WAP610N?

Jan 17, 2012

Is there a way to view the connected devices on the WAP610N?

View 3 Replies View Related

Linksys Wireless Router :: Internet Access Regarding Linksys E2000

Aug 21, 2011

I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).

View 9 Replies View Related

Linksys Wireless Adapters :: E2000 Is Connected At 5.0 / Should Have A Faster Connection

Dec 9, 2011

I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps.  When I switch back to 2.4 she shows 144.  I thought that when the e2000 is connected at 5.0 she should have a "faster connection".

View 1 Replies View Related

Linksys Wireless Router :: E2000 - Unable To Access Web Setup

May 12, 2012

Just a day or two ago I was able to do what the title says, didn't make any adjustments to my E2000 while in it, had to find something though.Anyhow, connecting to http://192.168.1.1 results in "Unable to Connect", etc. Also tried it in IE9, Firefox Beta is my primary, and it still didn't work. Tried using Cisco Connect and it says it cannot connect to my router. I am wired to my E2000, which in turn is wired to my DSL modem (Actiontec GT701D-Its firewall not in use). I sitll have full connection to the internet as well as other wireless deveices do in my house.

View 1 Replies View Related

Linksys Wireless Router :: Enable Guest Access On E2000?

Feb 12, 2013

How do I reenable guest access on my e2000 without having cisco connect installed?

View 1 Replies View Related

Linksys Wireless Router :: E2000 Not Allowing Access To Other Devices

Nov 5, 2011

I just set up my e2000 on a PC using Windows 7.  I am additionally trying to set up additional devices on the network.  The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
 
I can't get these on the network through the e2000.  They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security.  What do I need to do to successfully put the above devices on the network?

View 2 Replies View Related

Linksys Wireless Router :: E2000 Block All Internet Access?

Mar 12, 2012

E2000 about a years old.One of the rule is to block internet access from 1am to 4am for certain internal IPs.Working fine until a week ago. Once the time kick in, the E2000 will not route any internet access for any internal IP until the unit is power off and power on reboot.If that rule is disabled. then the E2000 will route all days and nights with no problem.Updated firmware to 1.0.0.4 already.I replaced the WRT45 because of the same problem a year ago. Now just about a year, this E2000 keeps blocking all traffic.

View 1 Replies View Related

Linksys Access Point :: WAP54g Repeater Showing As Device But Is Not Connected

Jan 28, 2012

I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?

View 1 Replies View Related

WRT54gl / N Access Point Connected To G Router

Jul 16, 2013

Any issues connecting an N access point via an ethernet cable to a G router?I currently have a wrt54gl router in one room (where it's connected by cables to various devices). I'm usually in another room and connect via wifi with other devices. Internet speeds over wifi are fine, but speeds are too slow when transferring files from wifi devices to other computers (windows file sharing).

I'm thinking of running a cable through a wall from the wrt54gl room to the other room and connecting a small N router, in access point mode. I'd then connect to the N access point and, through it, to the main router and other devices in the network.All wifi devices can run N.

Are there any issues in doing this? Anything I should know about configuring this? From other questions, it's not clear if I should use the same SSID for both routers. For that matter, should I turn off wifi on the wrt54gl?

View 1 Replies View Related

Linksys Wireless Adapters :: E2000 / Signal Strength Drops To 50% When Connected

Jan 2, 2012

I have the following problem:
 
Adapter: WMP600N
Router: E2000 (N-only)
OS: Windows 7 X64
 
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)

View 4 Replies View Related

Linksys Wireless Router :: E2000 / Remote Desktop Access With Mac And Asus Transformer Prime?

Jul 31, 2011

I have an E2000 router with the most current firmware. I have a Sony VAio laptop with Windows 7 Home Premium 64bit,a Macbook with 10.6.8, and a new Asus Transformer Prime with ICS.My work desktop is a Dell Optiplex 380 with Windows 7 Pro 32bit. I frequently work from home and have no issues remoting into to my work PC from by Sony laptop via VPN and RDP.However I have never been able to connect successfully to my work PC with my Macbook(using Remote Desktop Connection 2.1 for Mac OS) or Asus tablet(using WYSE Pocket Cloud RDP app for Android). I can however connect to the VPN itself on the Macbook and tablet without issue same as my Windows laptop. The other interesting part is I can connect via RDP when I am connected to a Mi-Fi 3g hotspot. So it is definitely something in the my Linksys E2000 blocking the connection for some reason. I have even set Port forwarding of 3389 with the ip's of both the Macbook and Asus tablet.I have also tried connecting via ethernet to the router with the same outcome. I cannot ping my work pc from either device as well.In addition the firewall on my work PC is completely disabled and all services related to Remote desktop access are enabled and running.

View 3 Replies View Related

Linksys Wireless Router :: E2000 Internet Access Is Not Affected When Printer Appears To Be Offline

Jun 10, 2011

I've got a Linksys E2000 router and a Brother MFC-7840W wireless printer and they don't seem to want to play nice together.  The set-up process was fine and I can usually print wireless without a problem, but every so often I'll try to print and my computer will say that the printer is offline.  Other computers on my network also show it as offline. The printer confirms it has an IP address, but even after power cycling it won't be picked up by my machines.  I've even tried a full reset of the printer and re-configured it, at which point it is able to successfully obtain an IP address, but it still shows as offline on my PCs. 
 
The only solution I have found is to powercycle the router.  This always works.  Now that's not a terribly inconvenient workaround most of the time, so I've been doing that for a few months now.  It obviously implicates the router as the point of failure, but wireless internet access is not affected when the printer appears to be offline, so obviously some packets are getting through normally. 

View 3 Replies View Related

Belkin Routers :: N300 Wireless Bridges Be Connected To Same Access Point

Nov 21, 2012

Can 2 N300 wireless bridges be connected to the same wireless access point ?

View 1 Replies View Related

Cisco Wireless :: WAP321 - Clients Connected To Single Access Point?

Oct 15, 2012

How many wireless clients can connect to a single WAP321 Access Point?            

View 2 Replies View Related

Cisco Wireless :: 1552E - Sensor Connected To Mesh Access Point

Jan 21, 2013

A 1552E has a temperature gauge sensor connected to its power over Ethernet port. the port status shows line protocol as down.The cable from 1552 to the sensor has been changed twice. We can see the 1552E gig1 interface is at 1000full duplex. Is there any chance the speed is causing the problem here. it seems the 1552E doesn't allow to set different speed & remains on 1000.

View 2 Replies View Related

Linksys Wired Router :: Remote Access To LAN And Cannot Connect To RVS4000

May 31, 2012

I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000.  I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.).  I do not use DHCP as all the LAN units are static addressed.  I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues.  I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.

View 1 Replies View Related

Cisco Routers :: RVS4000 / ISP WISP Point To Point Network Project?

Nov 30, 2012

Currently in place  ISP WISP Point to Point network would like some pointers to exceed in doing it right.  Here are some issues.ISP Fiber 50 Megs down and 50 Megs up  ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?

  a. Due to Port forwarding

  b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1 

1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1

a. Can I setup 74.144.55.159:85 to see 10.1.19.33?

My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx)  Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought.  90% of users are out in  the country without high speed internet.

View 1 Replies View Related

Linksys Wired Router :: RVS4000 - Secure Web Access Without Installing Other Software?

Mar 15, 2011

Does it support SSL VPN? As I would like to have secure web access without installing other software.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved