Linksys Wireless Router :: E2000 - Unable To Get Nanostation GUI When Connected
Feb 18, 2013
I am connected to my ISP via Nanostation 5 IP Add:192.168.10.186 S.M: 255.255.255.0, the Nanostation Lan cable is connected to the WAN port of my Linksys E2000, I am using a PPOE connection with my ISP, the Linksys broadcast a new network using DHCP service, The broadcasted Network is 192.168.5.X 255.255.255.0, the thing is i am unable to get the Nanostation GUI, when i replace the Linksys with a TP-Link router i have no such problem becuase in TP-Link i can add an additional IP address which is the Nanostation's IP,Is there any way i can get the Nanostation GUI?
View 3 Replies
ADVERTISEMENT
Dec 27, 2012
Unable to get Nanostation GUI when it is connectedI have a smart panel in the basement of my house which has a WRT160Nv2 in it. Connected to it in one port is a WRT610N which is on the second floor. Heres my issue now, for my main and computer rooms they are running off of one switch right (I'm not sure the IP of it or even how to find the IP of it) but basically any device connected to the smart panel router via ethernet cable is not recieving internet, devices connected wirelessly are.
View 3 Replies
View Related
Oct 18, 2010
How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies
View Related
Feb 26, 2012
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
View 3 Replies
View Related
Nov 19, 2011
Problem: My PS3 displays An Ethernet cable is not connected almost immediately after logging in. I am connected through a Linksys E2000 router. If I reset the cable modem, it will work for 10-15 minutes until it errors out again. If I plug the PS3 directly into the cable modem, it works fine. I'm really confused. I do not believe it is the router, as my computer is also connected to the router, and works fine. My Touchpad is connected wirelessly and also works fine. I do not believe it is the PS3, because it works fine if I plug it directly into the cable modem. I tried switching to wireless and it finds a lot of other signals (including mine), but I have the same problem if I choose wireless.I first had this problem with a launch PS3 and a Netgear router after almost three years of no problems.
View 8 Replies
View Related
Aug 28, 2011
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
View 2 Replies
View Related
May 12, 2012
Just a day or two ago I was able to do what the title says, didn't make any adjustments to my E2000 while in it, had to find something though.Anyhow, connecting to http://192.168.1.1 results in "Unable to Connect", etc. Also tried it in IE9, Firefox Beta is my primary, and it still didn't work. Tried using Cisco Connect and it says it cannot connect to my router. I am wired to my E2000, which in turn is wired to my DSL modem (Actiontec GT701D-Its firewall not in use). I sitll have full connection to the internet as well as other wireless deveices do in my house.
View 1 Replies
View Related
Sep 10, 2011
So, I've been having problems with connecting my HTPC to the E2000. I had an old D-link router + USB Wireless N adapter, but after the Dlink died, I bought the E2000, and upgraded to a faster N Adapter. Anyway, connection had been sketchy using the WPA/WPA2 encryption. I turned it off completely, and did get some better wireless speeds. I couldn't leave it open, though, as there are tons of laptops around my apartment that end up connecting to my network. Connecting wirelessly using that particular adapter continued to give problems. Two blackberries plus a Nookcolor connect with no issues (maybe because they're wireless G, who knows).
I then decided to reset the router by simply pressing and holding the reset button as I've done on all my other routers. It did reset, and reboot, but when it came back on, it would no longer connect to the internet. I've connected directly to my modem, and that works fine, but once I connect to the router...nothing. I did a hard reset (30/30/30), and that cleared everything, it seemed. The HTPC now connects easily, but there is still no internet connection. This is proving to be very frustrating.
Is there something I could have done wrong by doing that very first reset? Is there anyway to configure to get back my internet connection?
View 4 Replies
View Related
Jan 28, 2012
I am unable to get my E2000 router to recognize my Ipad2 when trying to connect.
View 2 Replies
View Related
Mar 24, 2011
I have a new Linksys E2000, I was unable to connect one of my laptops to the internet, so I decided to call support with the problem, after 45min and not results, find out that the E2000 do not support the Atheros AR 5007, they told me that I need to get a new driver for my adapter. Fine but Cisco doesn’t have a Driver update for this problem or how to fix it, or at least send you a link where to get the fix.
View 4 Replies
View Related
Dec 9, 2011
I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps. When I switch back to 2.4 she shows 144. I thought that when the e2000 is connected at 5.0 she should have a "faster connection".
View 1 Replies
View Related
Jan 2, 2012
I have the following problem:
Adapter: WMP600N
Router: E2000 (N-only)
OS: Windows 7 X64
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)
View 4 Replies
View Related
Jul 3, 2011
I cant see in my network the devices connected to SE2500 just the SE2500 itself. The internet access of the devices connected to SE2500 is working correctly. Is this a problem?
View 3 Replies
View Related
Jun 23, 2012
WD essential 2GB hard drive connects OK through cisco connect but when I click on the shortcut or try to access the drive I get access denied duer to permission to the ip address
View 4 Replies
View Related
May 8, 2012
I can't connect on my 2500 on my xp system. I just wiped the drive and did a fresh install on everything due to a virus. I updated xp/ and drivers and installed the ae2500 drivers. When I try to log on it starts to and shows connected however, it tells me "windows was unable to find a certificate to log you on to the network" I noticed that this system has the same ae2500 with windows vista and uses wpa2-personal, aes. The xp system only has options for wpa-personal, aes. Is this the problem or is it something else?
View 1 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Oct 2, 2011
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies
View Related
Jan 28, 2012
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies
View Related
Nov 3, 2011
E2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies
View Related
May 28, 2012
I've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies
View Related
Apr 24, 2011
My internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies
View Related
Aug 28, 2011
I have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies
View Related
Dec 7, 2011
I'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
View 2 Replies
View Related
Nov 14, 2011
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies
View Related
Apr 21, 2013
I have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
View 4 Replies
View Related
Sep 7, 2012
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies
View Related
Nov 11, 2011
For Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies
View Related
Oct 28, 2011
Im using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
View 4 Replies
View Related
Nov 11, 2011
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
My router is version 1.0, with 1.0.04 firmware.
View 3 Replies
View Related
Jul 11, 2011
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
Using windows 7 64 bit
Using newest dirvers and firmware from Linksys.
View 4 Replies
View Related
Jan 31, 2012
I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
View 5 Replies
View Related
Jul 2, 2011
I have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies
View Related
