Linksys Wireless Adapters :: E2000 Is Connected At 5.0 / Should Have A Faster Connection
Dec 9, 2011
I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps. When I switch back to 2.4 she shows 144. I thought that when the e2000 is connected at 5.0 she should have a "faster connection".
View 1 Replies
ADVERTISEMENT
Jan 2, 2012
I have the following problem:
Adapter: WMP600N
Router: E2000 (N-only)
OS: Windows 7 X64
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)
View 4 Replies
View Related
Sep 8, 2011
when I switch my e2000 wireless setting to 5 ghz the wireless devices don't work
View 2 Replies
View Related
Oct 18, 2010
How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies
View Related
Feb 18, 2013
I am connected to my ISP via Nanostation 5 IP Add:192.168.10.186 S.M: 255.255.255.0, the Nanostation Lan cable is connected to the WAN port of my Linksys E2000, I am using a PPOE connection with my ISP, the Linksys broadcast a new network using DHCP service, The broadcasted Network is 192.168.5.X 255.255.255.0, the thing is i am unable to get the Nanostation GUI, when i replace the Linksys with a TP-Link router i have no such problem becuase in TP-Link i can add an additional IP address which is the Nanostation's IP,Is there any way i can get the Nanostation GUI?
View 3 Replies
View Related
Feb 26, 2012
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
View 3 Replies
View Related
Nov 19, 2011
Problem: My PS3 displays An Ethernet cable is not connected almost immediately after logging in. I am connected through a Linksys E2000 router. If I reset the cable modem, it will work for 10-15 minutes until it errors out again. If I plug the PS3 directly into the cable modem, it works fine. I'm really confused. I do not believe it is the router, as my computer is also connected to the router, and works fine. My Touchpad is connected wirelessly and also works fine. I do not believe it is the PS3, because it works fine if I plug it directly into the cable modem. I tried switching to wireless and it finds a lot of other signals (including mine), but I have the same problem if I choose wireless.I first had this problem with a launch PS3 and a Netgear router after almost three years of no problems.
View 8 Replies
View Related
Aug 28, 2011
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
View 2 Replies
View Related
Feb 21, 2010
I have been trying to get the WUSB600N v 1 to enable in Win 7 Pro 64 bit for quiet awhile. Been reading all the posts here and elsewhere. Have tried all the drivers I could down load and still no luck. The drivers would install but the adapater would not enable. Read about some of the problems with Kaspersky but I had Zone Alarm installed and it did not have the same problem. So tonight I decided to completely remove Zone Alarm from the system. Once I removed ZA and rebooted the adapter functioned correctly. I am able to enable and connect using the WUSB600N v 1. Reinstalled ZA and 600N is still working correctly. It just would not install correctly with ZA on the system. I had previously tried disabling ZA but it took a complete removal to get it to work, I even tried it in safe mode but no luck. I don't have a clue as to what ZA was doing to block the adapter from working but it did. So if you have any kind of anti-virus or firewall you might try removing it and see it the adapter will work. I am currently using the latest drivers from the Ralink site but they would not work either until I removed ZA.Message Edited by curlysir on 02-22-2010 06:30 PM
View 9 Replies
View Related
Feb 28, 2011
I recently installed this adapter, and it's connected to a wireless-N router right now (WRT102N), the problem I'm having is it's not sending out internet connection once I boot up the next day. It'll work once I click reconnect to connect to the network again, but still, I don't think it should be doing that.
View 4 Replies
View Related
May 8, 2012
I can't connect on my 2500 on my xp system. I just wiped the drive and did a fresh install on everything due to a virus. I updated xp/ and drivers and installed the ae2500 drivers. When I try to log on it starts to and shows connected however, it tells me "windows was unable to find a certificate to log you on to the network" I noticed that this system has the same ae2500 with windows vista and uses wpa2-personal, aes. The xp system only has options for wpa-personal, aes. Is this the problem or is it something else?
View 1 Replies
View Related
Nov 5, 2012
After upgrading two laptops to windows 8, they will no longer appear as a connected device under the "device list." They both access the router via wifi and wired, but neither appear in the device list any longer. I've rebooted the router twice, as well as both computers, disabled/re-enabled their wifi connections, but no effect.Every other non-Windows 8 device still appears normally under the device list.
View 3 Replies
View Related
Apr 4, 2013
desktop with Windows 7. It is connected to the internet in my office thru Uverse (AT&T). We previously had a standard router, but upgraded since it seemed to be moving too slow. This problem with the adapter existed then also and we thought maybe it was too many computers slowing down the router.The adapter works great until I try to open certain websites. Then it loses its mind. I get a popup that says "Dial Up Connection" and wants me to choose to connect or work offline. When I click connect, I get a second window that says "Connecting through WAN Miniport", but it never actually connects to the page. Then lastly, a third popup says it has an error connecting and wants to redial and starts a countdown. But again, it never connects to the page.
View 3 Replies
View Related
Jul 16, 2012
I have a WMP110v2 card installed in my desktop. It can connect to my wireless network, but it cannot access the internet. Other computers on the network can connect to the internet (wired and wireless), so I know it's not a problem with my modem/router. I have tried reinstalling the device several times, but nothing seems to work. It receives a valid IP address, but when I try to ping my router, all packets are lost.I'm completely lost on what to do next.
System specs of the PC in question:
Dell Dimension 3100Windows XP Media Center Edition, SP3
Intel Pentium 4 CPU @ 2.99GHz
1GB RAM
View 1 Replies
View Related
Aug 30, 2011
I am using a E2000 connected to a DSL modem via the internet port. My modem is able to connect at gigabit speed but it doesn't seem to be the case with the E2000. All other ports are running at gigabit speed without problem. Is there any parameter that can be modified or is it a router limit?
View 2 Replies
View Related
Sep 18, 2012
I recently purchased a Mac and wanted to reset my wireless router and set it up using my mac. However, when I downoaded the software to set it up again, it said it was not compatable with my Mac OS (X Lion 10.7.4). I am sure there is a way to manually set it up via an ethernet connection, but I am at a loss as to how to do that. The wireless router is working just fine, I am able to connect to the internet wirelessly and there's nothing wrong with my internet service, however the wireless router is not secured.I have my Mac connected to the wireles router via an ethernet cord.
View 1 Replies
View Related
Aug 12, 2011
i want to set up a vpn connection to my home network. i see that the e2000 supports ipsec, but does not provide a client. what client can i use to establish a connection?
View 4 Replies
View Related
May 5, 2012
I switch on router and connect my iPad on router linksys cisco e2000. During 10 minutes, There is no problem. After 10 minutes, I have always the connection with my router but no internet. To Avoid this problem, i restart the router with switch and after, no problem. Do you have any ideas to avoid this lost connection after 10 minutes when I switch on my router.
View 2 Replies
View Related
Sep 10, 2011
I have 300 Mb/s plan from ISP. Then cable connected directly to PC my throughput is as it should be, but then i do connect my PC via E2000 cable connection, it slows down to 200Mb/s. I have tryied also E4200 model and i have same issue.
View 1 Replies
View Related
Sep 13, 2011
Internet was working great a few days ago with my e2000 and comcast as my ISP. I've got a few devices connected through ethernet connections on the unit. We also connect to the e2000 wirelessly.Problems started yesterday with no internet. Last night I rebooted everything and still nothing works. Connected laptop to cable modem directly. Wasn't getting internet connectivity so I called Comcast. They reset my modem and everything started working fine. Now I can directly connect from cable modem to laptop and internet works fine. I try connecting the modem to the router and still no internet.
View 2 Replies
View Related
Feb 7, 2013
I recently downloaded Deluge and while I can download torrents without a problem, I always have the "NO INCOMING CONNECTIONS' warning. I've tried single port forwarding, port range forwarding, turning UPnP off and on ... in short I've tried a lot of stuff and the only thing that clears the message is to remove the router out of the equation. The message disappears as soon as I connect the pc directly to the modem.
View 3 Replies
View Related
Jun 14, 2012
My connection to Davis Instruments' WeatherLink had been working for many weeks, when my old WRT54G quite renewing DHCP leases. I've replaced it with a new E2000. All seems well. The Wifi network is working and my server resources to the outside are working. But the blasted WeatherLink software complains that it can't connect to to the interface box. This is a wired connection. The software finds the MAC address of the interface box and the assigned IP address, but "testing" the connection fails. I can ping the IP address of the interface box. The Davis people insist this is an issue with the router. The WeatherLink software uses a weird port: 22222 I didn't know there were ports with 5 digits. I've tried port forwarding this to the IP of the computer, but nothing changes. I think if I can ping the IP of the interface from the computer, communication should work.
View 1 Replies
View Related
Jun 28, 2010
I use to use 2 routers, one for me and my dad, another for my brother and sister. We decided to get rid of the other router, and make our cisco E2000 our main router, but, everything on the router settings got removed so we had to reset it up. I remember reading an advanced setting guide on making my wireless speed go from 13.5MBPS to 216 MBPS, but i forgot what the settings was in advance settings.
View 7 Replies
View Related
Jun 19, 2011
why my wireless connection on my laptop is significantly better than my wired connection to my desktop. Internet ran just fine on the desktop at my old apartment; got to the new place, and now it's having serious issues.
After working on this problem for a while, I have come to the conclusion that for some reason, I am getting serious packet loss, consistently, at a particular "hop" on my desktop, which is not present on the laptop.Here are the Line Quality tests that illustrate the problem better than I could ever describe it in words:
Laptop: Line quality test packet loss and latency | DSLReports.com, ISP Information
Desktop: Line quality test packet loss and latency | DSLReports.com, ISP Information(and it appears they both fail the initial test, but the laptop connection runs just fine).
So at that one specific hop (ae-1-0.cr0.chi10.tbone.rr.com, I have no idea what that means), my desktop connection suffers serious packet loss while the laptop is more or less OK.This discrepancy is evident in the quality of connection on my desktop, while the laptop runs just fine. Here, in summary, is what I have tried:
-Going wired through laptop using same cables, ports, and router as desktop: laptop performs flawlessly.
-Updating router firmware, NIC card drivers, and Windows on the desktop
-Full virus disk scan and boot scan using Avast; full malware scan using Malwarebytes; Windows disk defrag
-Disabling QoS packet scheduler
-Performing netsh /flushdns; winsock reset; ipconfig release, renew
-(Temporarily) disabling Antivirus program
All of these actions together have made the desktop connection USABLE... however it is by no means an acceptable level of quality for a cable connection, and not nearly as good as any other in the apartment gets using the same connection, whether wired or wireless.The only visible difference I can find between the laptop and the desktop is the packet loss that is present at that one hop in particular, which is extremely debilitating for the desktop's connection.
Further info:
Desktop specs:
Realtek PCIe GBE Family Controller NIC (onboard on the mobo)
Windows XP Home Edition Version 2002 SP3
Intel Core 2 Duo E8400, 3GHz
2 GB Ram
Plenty of Disk space
Router:
Belkin F5D9230-4 Wireless G Plus MIMO Router
Here is the previous thread that details my troubleshooting efforts thus far; as the question has now become something entirely different, I thought it more appropriate to make a new thread.
Wiresless faster than wired connection
View 12 Replies
View Related
Jun 21, 2010
I bought a brand spanking new Linksys E2000. I get great connection speeds and awesome range, until the day I set up parental controls. Once I set them up, It slowed my connections down to a crawl. Thinking that I did something wrong, I reset the router and did the entire installation. Everything was back to normal, but it did it again once I set up the parental controls.
View 9 Replies
View Related
Sep 5, 2012
I have a Linksys WUSB100 ver.2 which i'm using on my desktop (uptodate Windows 7) for over a year now. I never had any problems with it until about a week ago.
After starting the computer, it had no network-connection, nor could it find any network anymore . The led-light keeps flashing blue and the device gets pretty hot.
I've tried about everything, i think:
- I've tried to update the drivers, but the installed driver were already uptodate.
- I have re-installed the device with no effect.
- i've installed the device on 2 other computers; my Windows 7- laptop and my old Windows XP SP3-computer. The problems were the same there.
View 2 Replies
View Related
Jan 28, 2012
I have a Cisco Linksys WRT120N wireless router in one bedroom. On another bedroom which is hardly 15 feet away, I have set up my laptop to connect to it via a Cisco Linksys AE1000 wireless USB adapter. There are two thick walls between one bedroom and another.
Neverthess I find AE1000 dropping connection all the time. There are times I unplug the laptop and take into the same room as my router but it still doesn't connect. The wireless strength constantly varies from Very Good to Excellent but no matter what I try AE1000 never connects to it. If I restart my laptop, sometimes it does connect.
All in all its very frustrating that two Cisco products can't communicate effectively with each other.
P.S: I have both my ASUS tablet and my verizon droid both connecting to the wireless router from the same room as my laptop without any issues.
View 9 Replies
View Related
Dec 31, 2008
I purchased a WRT110 wireless router several weeks ago. Used it with my WPC55AG with no problems at all. I liked the wireless-N, so I decided to upgrade to a wireless-N notebook card and purchased a WPC100. I can always connect to the router with 100% signal strength. However, when trying to access the Internet, sometimes I can connect to websites, but I regularly get an error message that Internet Explorer cannot connect to the internet, even though the signal strength is still 100%.
Tried going back to my WPC55AG and do not get any connection error messages. Tried connecting to my router with my PSP and do not get any connection error messages. Connected to another wireless router that didn't have WPA or WEP using my WPC100 and didn't get any connection error messages..
View 5 Replies
View Related
Dec 20, 2009
I bought the WMP600N because Linksys and Microsoft listed it as 'compatible' for Windows 7 x64. My experience:
- unstable and weak connection
- pings to websites like google.com drops, average: 1 out of 3
- low signal, on the same spot my three years old HP-laptop with 'a build in wireless card' has full signal strength in Windows 7
- it works well under Windows XP (32 bit)
I am convinced that drivers for the WMP600N are not ready for Window 7 x64. Linksys (or Ralink, which developed the chipset), release a proper driver for the WMP600N.
View 9 Replies
View Related
Feb 23, 2011
I'm using the WUSB54GSC on a IBM Desktop computer, not old, but not new by any means. We have wireless internet through Comcast, and my room is on the second floor. The router is on the first floor, but it's almost just underneath my room. The internet seems to connect completely fine, but it will disconnect at some things. For example, when I tried to go to mapquest, it was like it was flooding, and it dropped the internet connection. I also play games online, and when I play the actual game itself (GTAA/Online) it plays just fine, no lag, nothing like that, but when I try to connect to Teamspeak, when it's loading the channels after it connects, it just drops the connection..
View 1 Replies
View Related
Jan 24, 2013
I had this card working on this notebook with Windows XP, but with only 256mb ram it ran too slow. So I went back to 2000 on it. But I can't get the card to work, I've tried using the setup, the link light on the card does flash on and off. But in the linksys program just says no association with access point and says WPC54GS is inactive. I tried just installing the driver when it detects it but that didn't work. Also I try to start the wireless configuration and just get error 1747 the authentication service is unknown. What do I need to do to get the card working on here so I have internet access?
View 5 Replies
View Related
Nov 6, 2011
Every now and then my adapter won't be able to connect to the internet for a few minutes, and then it just comes back. This happens frequently, varying from every few minutes to every few hours. If I re-connect the adapter, though, a connection instantly comes back. There's no sign that it's lost connection, the taskbar still displays Internet access and a 5 bars, and the blue light on the adapting keeps flashing; but I just can't connect to the iternet at all.
View 1 Replies
View Related
Oct 1, 2010
I have the problem that my WUSB600N loses the connection to the internet after a few minutes. I boot the system and the wireless stick run impeccable. After a few minutes the windows 7 network icon show me a yellow exclamation mark and no more internet access is possible. When I unplug the WUSB600N from the system und plug it on again the internet connection is possible again and run then over houres without a problem.
View 8 Replies
View Related
