Linksys Wireless Adapters :: WMP110v2 Connected To Network But Cannot Access The Internet
Jul 16, 2012
I have a WMP110v2 card installed in my desktop. It can connect to my wireless network, but it cannot access the internet. Other computers on the network can connect to the internet (wired and wireless), so I know it's not a problem with my modem/router. I have tried reinstalling the device several times, but nothing seems to work. It receives a valid IP address, but when I try to ping my router, all packets are lost.I'm completely lost on what to do next.
System specs of the PC in question:
Dell Dimension 3100Windows XP Media Center Edition, SP3
Intel Pentium 4 CPU @ 2.99GHz
1GB RAM
I can't connect on my 2500 on my xp system. I just wiped the drive and did a fresh install on everything due to a virus. I updated xp/ and drivers and installed the ae2500 drivers. When I try to log on it starts to and shows connected however, it tells me "windows was unable to find a certificate to log you on to the network" I noticed that this system has the same ae2500 with windows vista and uses wpa2-personal, aes. The xp system only has options for wpa-personal, aes. Is this the problem or is it something else?
My main pc is running Windows 7. It is also running MS Windows firewall and anti-virus. It connects fine to the internet via an ethernet connection to the WRT610N.
I am trying to access the internet wirelessly from another pc running Windows XP. The wireless pc indicates it is connected to the network with excellent signal strength. It will not connect to the internet. I can successfully ping the router but it is unsuccessful when pinging an internet address.
An additional wireless pc (WinXP) and my phone (Android) also show connected to the network but will not connect to the internet.
These wireless computers used to be able to access the internet before we moved house. They only thing I think that has changed is the addition of Windows firewall and anti-virus. It may however be something else.
I have a WET610 that I intend to use to connect a PC to the local network and further on to the Internet. The local connection works, I can ping to and from the computer connected to the WET610 and I can see the other computers, both wired and wireless, on the network so the wireless connection is ok but I can't connect to the Internet, I can't even ping the DNS I'm using. What can be wrong? All the other computers can access the Internet. The WET610 talks to a wireless AP which in turn is connected to a router
I have an AT&T Gateway Wireless router to connect to Internet with my wired computer. In another room, I have another wired computer I also use to connect to Internet. I never have problems connecting to Internet from computer that is hooked up to the router, but I often have Internet connection issues from the computer in the other room. It can find the access point, but not connect to Internet. I reinstalled the WUSB300N driver again, but I still cannot connect.
I can not connect to my home wireless network (we did change routers back in Dec and did at that time have problems as well getting it to connect) the router is a Linksys E2000.when I checked further I saw that the IP address was different than the ones on my other laptops so I changed those settings by adding the new IP address..
There is a problem with establishing an internet connection between my laptop and any wireless network, and hence the internet cannot be accessed. Though, the connection can be established locally between my laptop and the wireless network for a short while before the connection is lost locally. There is certainly no problem with my current wireless router as there are internet connections between the wireless network and other devices. Prior to using the current wireless router, I used Linksys WRT54G for internet connection until recently when there was no connection between all devices and the Linksys wireless router, so I changed my wireless router to the current one. However, the problem still persists for my laptop. I can only get access to internet when my laptop is connected to the router using ethernet cable, as well as when my laptop is connected to the main cable modem using the same cable.My laptop model is Fujitsu Lifebook S Series and my laptop is running on Windows Vista Service Pack 2 and my current wireless router is Belkin N300 Wireless N Router Model F9K1002v1.What I have done so far are that I have ensured that the DNS client and DHCP client service are enabled and that I have used the method of "/release, /dnsflush and /renew" on the command prompt.Below is the /ipconfig /all description when this laptop is connected to the cable modem using ethernet cable:
Windows IP Configuration Host Name . . . . . . . . . . . . : FujitsuUser-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Broadcast IP Routing Enabled. . . . . . . . : No
I have been trying to get the WUSB600N v 1 to enable in Win 7 Pro 64 bit for quiet awhile. Been reading all the posts here and elsewhere. Have tried all the drivers I could down load and still no luck. The drivers would install but the adapater would not enable. Read about some of the problems with Kaspersky but I had Zone Alarm installed and it did not have the same problem. So tonight I decided to completely remove Zone Alarm from the system. Once I removed ZA and rebooted the adapter functioned correctly. I am able to enable and connect using the WUSB600N v 1. Reinstalled ZA and 600N is still working correctly. It just would not install correctly with ZA on the system. I had previously tried disabling ZA but it took a complete removal to get it to work, I even tried it in safe mode but no luck. I don't have a clue as to what ZA was doing to block the adapter from working but it did. So if you have any kind of anti-virus or firewall you might try removing it and see it the adapter will work. I am currently using the latest drivers from the Ralink site but they would not work either until I removed ZA.Message Edited by curlysir on 02-22-2010 06:30 PM
So I have a Windows HP Pavilion w1907 desktop. My computer says that I am connected to a wireless network. However, I cannot use any programs, like AIM or Mozilla Firefox, iTunes, or any other programs that require internet connection to work. I visited the Network and Sharing Center, which says I'm connected to an unidentified network but not the Internet.
So I have a Windows HP Pavilion w1907 desktop. My computer says that I am connected to a wireless network. However, I cannot use any programs, like AIM or Mozilla Firefox, iTunes, or any other programs that require internet connection to work. I visited the Network and Sharing Center, which says I'm connected to an unidentified network but not the Internet.
Linksys Wireless router connected but no access to the internet. I do not have a modem in my flat from ISP, only a cable, since the internet is set for every apartment in the building. I have a username and password that I use to connect. There is no problem connecting with the cable. I set up by Belkin wireless router and I'm actually connected to internet wireless but it only works if I also enable the primary ISP connection on my computer so my laptop is connected to internet without a cable. But this weird connection does not allow me to connect my phone to wireless or any other computer. Also the router settings site says not connected to internet and the internet light on Belkin is off.I have a Slovenian ISP -Amis, cable connection and Belkin Wireless modem, Avira Free antivirus.
I recently installed this adapter, and it's connected to a wireless-N router right now (WRT102N), the problem I'm having is it's not sending out internet connection once I boot up the next day. It'll work once I click reconnect to connect to the network again, but still, I don't think it should be doing that.
I have a hardwired HP computer with no problem connecting. The remainder of my wireless devices will not access internet. No problem until about 3 weeks ago then all of a sudden it stopped. All wireless devices detect the router/network, but will not allow access to the internet.
I have a Linksys E1000 device that is connected to a DSL connection through a modem. I have a Laptop that is wirelessly connected to the router and a PC that is connected via cable. Lately, a problem started to occur where the router keeps losing the internet connection and Laptop tell me that it connected to the router but there in no internet access and the same thing happens to the PC, both disconnect at the same time. I called my ISP company when this happens and they told me that the connection is working fine and everything look ok from there. I connected my PC directly to the modem and it worked fine so problem is not from modem. When i go to the router settings at the moment this occurs, it shows that all IPs are 00000 and status is "Connecting" and then it connects and changes to "connected" and everything fine till like 15 minutes later where this happens again (sometimes, it actually disconnects again after like 15 seconds!). I took the router to the dealer and he examined it and told me there is nothing wrong but he updated the firmware and told me to try it but same thing so he exchanged it for a new one and problem is still there!
i have a WRT54G2 and i have it plugged in. i want to avoid downloading things but i had this thing working a month ago, it says its connected but no internet connection.
I've looked through the forums and FAQs and haven't seen anything that resolves my issue. I recently moved from the US to Japan. I had my WRT54GS set up in the States and the network worked fine. When i got here, i set it up, hard reset the router and set up a new network.
I can access the internet when connected through the router via ethernet cable, but I cannot connect any of my wireless devices. Easy Link Advisor says "internet connection is not working" but it is. I have two computers connected via cable and they both work so it is not an issue of my ISP allowing multiple IP addresses.
My wireless devices (XBox, PS3, laptop) can see the network but cannot connect through to the internet. I also just noticed that the "wireless mode" according to the EasyLink Advisor says "disable", however the wireless settings on my 192. server webpage is set to "mixed" and seems to be correct in all settings to be on.
After upgrading two laptops to windows 8, they will no longer appear as a connected device under the "device list." They both access the router via wifi and wired, but neither appear in the device list any longer. I've rebooted the router twice, as well as both computers, disabled/re-enabled their wifi connections, but no effect.Every other non-Windows 8 device still appears normally under the device list.
desktop with Windows 7. It is connected to the internet in my office thru Uverse (AT&T). We previously had a standard router, but upgraded since it seemed to be moving too slow. This problem with the adapter existed then also and we thought maybe it was too many computers slowing down the router.The adapter works great until I try to open certain websites. Then it loses its mind. I get a popup that says "Dial Up Connection" and wants me to choose to connect or work offline. When I click connect, I get a second window that says "Connecting through WAN Miniport", but it never actually connects to the page. Then lastly, a third popup says it has an error connecting and wants to redial and starts a countdown. But again, it never connects to the page.
I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps. When I switch back to 2.4 she shows 144. I thought that when the e2000 is connected at 5.0 she should have a "faster connection".
I have am unable to access the Internet via my modem and router. My computer recognized the connection from my router. My modem is a Motorola 12DVC. My router is a Linksys Broadband Wireless-B BEFW11S4 version 4. I tried several things, including changes via 192.168.1.1. I am using an AT&T DSL connection. The router has only been used one time.
Here is some other information:
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:Documents and SettingsJim>ipconfig /all
I installed an E1200 wireless router yesterday and everything worked fine. However, I happened to turn off the modem overnight and now my computer indicates (under Wireless Network Connection) that I'm connected, but above (under Currently Connected To) it says that I have No Internet Access. I tried turning off the modem, router and computer and turning them on again in that order, but that didn't work. Do I need to do the set-up again ?
Adapter: WMP600N Router: E2000 (N-only) OS: Windows 7 X64
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)
I just moved in to a new place and have connected my Wireless router (WRT610N) to my switch located in the smart panel in the basement (SE2500). Plugging my ultrabook in to the wall confirms that the signal from the switch in the basement is being sent up, however if I plug my wireless router in to the jack and connect to the wireless router I have no internet access.
I am connected to my network wirelessly and I have Internet acces (according to the symbol at the bottom right) bu the Internet doesn't work. At the moment it keeps fluctuating between giving me interne and not I am using Skype to tell me if I have Internet ( when it's green I do when it's grey I don't) I have tried many things on forums like obtaining ip automatically or obtaining a fixed ip. I've tried renewing the ip and all this doesnt work.
Santa got a second-hand acer mini-laptop for my daughter this last Christmas and she accidentally pour some coke in it, I took it to the shop and I had to pay to repair it; when I got it back, the first thing is that originally it has Windows 7 and now XP, I thought it was ok, but even though I use my network passkey and everything, it quickly connected to the network showing internet access but when I open IE, it shows a message to diagnose connection problems, I run the repair wizard and nothing, but all the time it is showing that the connection is working, will I need to take it back to the shop or is there something I can do?
I can't connect suddenly to the Internet. I tried both Wired and Wireless connection to my laptop. The icon is showing that my laptop has detected the connection but has no internet access.Showing in my screen is: Connected to Network. IPV4 no internet access, IPV6 no internet accessI tried using my iPhone to connect via the wireless connection and I could get browse the Internet with it.. hence i'm sure the problem lies with the laptop.
I have three computers at home: 2 desktops and 1 laptop and they all run windows 7. For a week now I haven't been able to connect to the internet from one of the desktops. The initial setup was wireless and worked fine for years. I've tried every advise I could find online: Powered off and on the modem and the router, disabled and enabled the adapter, reseted WINSOCK and TCP/IP, assigned a permanent IP address, did a system restore to the last day the internet worked, turned off windows defender (windows firewall has always been off), turned off Webroot, I bought a new wireless USB adapter which connected to the network but still no internet access and my last resort: I got a really long ethernet cable and connected directly to the wireless router AND then directly to the modem... NOTHING! Still says that I am connected to an unidentified network and that there is not internet access.
I just bought a new laptop and have had issues with it from day one regarding the internet. It connects me to the internet, but then after a few minutes on the task bar where it tells you what you are currently connected to a yellow (!) shows up. It tells me that I am connected to my network, but it says that I do not have any or sometimes even limited internet access. I have other computers in the house (3 laptops, sometimes 4, and 2 desktops) that do not have any issues connecting or staying connected to the internet. The laptop with the issue has Norton installed on it and it is with Windows 7. My ISP is AT&T, DSL. My router is a LinkSys router.
