Linksys Wireless Router :: E2000 Software Can't Find Sonos When Pc Is Connected Through Wifi
Aug 28, 2011
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
View 2 Replies
ADVERTISEMENT
Oct 2, 2011
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies
View Related
Jul 13, 2012
Can't find client device for E2000
View 1 Replies
View Related
Oct 18, 2010
How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies
View Related
Feb 18, 2013
I am connected to my ISP via Nanostation 5 IP Add:192.168.10.186 S.M: 255.255.255.0, the Nanostation Lan cable is connected to the WAN port of my Linksys E2000, I am using a PPOE connection with my ISP, the Linksys broadcast a new network using DHCP service, The broadcasted Network is 192.168.5.X 255.255.255.0, the thing is i am unable to get the Nanostation GUI, when i replace the Linksys with a TP-Link router i have no such problem becuase in TP-Link i can add an additional IP address which is the Nanostation's IP,Is there any way i can get the Nanostation GUI?
View 3 Replies
View Related
Feb 26, 2012
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
View 3 Replies
View Related
Nov 19, 2011
Problem: My PS3 displays An Ethernet cable is not connected almost immediately after logging in. I am connected through a Linksys E2000 router. If I reset the cable modem, it will work for 10-15 minutes until it errors out again. If I plug the PS3 directly into the cable modem, it works fine. I'm really confused. I do not believe it is the router, as my computer is also connected to the router, and works fine. My Touchpad is connected wirelessly and also works fine. I do not believe it is the PS3, because it works fine if I plug it directly into the cable modem. I tried switching to wireless and it finds a lot of other signals (including mine), but I have the same problem if I choose wireless.I first had this problem with a launch PS3 and a Netgear router after almost three years of no problems.
View 8 Replies
View Related
Sep 5, 2011
I have a Dell Inspiron 1720 (running Vista Home Premium) that connects to my Linksys E2000 and to a wireless printer, the Canon MX870. It's been working for months without problems.
I just got a Toshiba Satellite P770-BT4G22 Laptop (running Window 7 Professional 64 bit) and installed the Cisco Connect software following the instructions where you have already set up the router and just need to install the software to do things like add a device. I can connect to the router fine using a web browser or the Cisco Connect Software and my Toshiba connects to the Internet through the router without problems.
The problem is Cisco Connect says it can't find a wireless printer when I run it on my new Toshiba. I've put the printer within 3 feet of the router with my Toshiba in between but still it can't find it. My Dell in another room connects to the printer no problem. And I can print to the Canon if I select the Shared Canon Printer ( on the Dell) using the Toshiba's Control Panel Add Printer function. But obviously that means the Dell has to be on so that's not good for much more than troubleshooting. I've also wired a connection from the printer to the Toshiba and downloaded the latest driver, printed that way so I know that's not the problem. The problem is that Cisco Connect can't find the printer. It says there are 6 devices attached to my router so it's seeing something, but I guess not the printer. I've turned any firewalls off for this testing too.
I'm stumped as to why it can't find the printer when the Dell did and they are all on the same network. Unless it's not compatible with 64 bit Windows.
View 7 Replies
View Related
Mar 9, 2011
After getting informed that I cannot use the AP I bought yesterday as a bridge, I decided to get another linksys E2000, as the guy in the shop informed me that I can run it in bridge mode for sure.Now, as I am doing this for the first time, and my english is not the best, I was not able to find some instructions, or even better a step-by-step manual that can assist me. I searched the forum, but I did not find anything about the E2000 in bridge mode.
View 7 Replies
View Related
Jul 29, 2011
i have a E2000 rounter . It's brand new. But i can't setup to use wifi. the software cisco connect can't find rounter. When i plug blue cab from e2000 to my ethernet port on my laptop , icon's network appearen " limit ".
View 3 Replies
View Related
Jan 5, 2012
My WiFi is working, but only to about 20 feet then it slows down to almost nothing...
View 1 Replies
View Related
Aug 20, 2012
I have an odd problem where every fortnight to three weeks none of my wifi devices (ipap, laptop, 2x android phones) can connect to my network (Linksys E2000, running firmware 1.0.04 with WPA2 personal). They can all see the network and try and connect, but all fail. Rebooting the router has no effect, and the only thing I've found that works is that I have to connect via ethernet cable (which works no problems) and then disable wireless security, save changes, and then immediately reenable wireless security and save changes again. All my devices then will automatically reconnect no problems. It's a bit annoying as my router isn't ideally placed to dig out the cable, but I wondered if there's any way of diagnosing what could be wrong? I've checked the router logs and they're not useful - the only thing I can see of note is in the DHCP log in the period when I suspect the problem arose I get 4 entries of discover / offer / request / ack going to 255.255.255.255 which seems unusual. But the security log is empty so I get nothing from that.
View 8 Replies
View Related
Jan 1, 2013
My 'main' Wifi SSID will just disappear and you can't connect to it. the guest account will still show up. computers/devices that are already connected will stay connected and will work fine, but anybody reconnecting will not be able to. Only solution I've found so far is to unplug and replug in my router
View 1 Replies
View Related
Aug 14, 2012
I have a Linksys E2000 router. I am trying to install an Epson NX230 printer on my home network. Apparently, the Epson printer has a MAC address assigned to it. My network cannot find the printer. I looked at my riuter setup and the MAC Address Clone has two buttons, Enabled Disabled. The Disabled button is clicked on. Accdording to documentation I foudn on this website, it looks like I can Enabled the MAC Address clone button. The document also mentgioend entereding the MAC address for a PC.
If I enable the MAC Address Clone, do I enter the MAC address for the printer or during the install process does the MAC address get installed also
View 9 Replies
View Related
May 24, 2012
I have a Linksys E2000 router on my home network. The router has the newest version of firmware. Every once in a while, wireless clients on my network become "isolated". Here's an example of what happens. I set up a new wireless printer. I can print to the printer wirelessly from my phone, PC's, etc. all fine after setup. I'm thinking everything is cool!! Well after 2 weeks to 1 month this device will become "isolated" so I cannot print to it; it has an IP address, it can ping its gateway, but i cannot ping it from other devices on the same subnet. I know it's not the printer because if i unplug my E2000 and plug it back in, it works fine.
Another example. I have two windows 7 PC's that are on the same home group and i can share files between them. Sometimes it works and other times it doesnt. I can ping my gateway but they cannot ping each other. I would troubleshoot the issue like crazy from the host end, but the second i unplug my E2000 and plug it back in, BINGO they can talk. Something is wrong with how these routers function with hosts in inter-subnet communications.
View 2 Replies
View Related
Dec 9, 2011
I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps. When I switch back to 2.4 she shows 144. I thought that when the e2000 is connected at 5.0 she should have a "faster connection".
View 1 Replies
View Related
Jan 2, 2012
I have the following problem:
Adapter: WMP600N
Router: E2000 (N-only)
OS: Windows 7 X64
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)
View 4 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Aug 23, 2007
I updated the Firmware...then the WRT54GC can't work now,it's power led green and red always,I can't ping 192.168.1.1 via wired or wireless.wireless led shutdown.my laptop can't find any wireless network.
View 9 Replies
View Related
May 2, 2012
I recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.
View 7 Replies
View Related
Dec 2, 2012
With my old routeur (wrt310n) I used to be able to limit the wireless speed.I cant seem to find the option with my new routeur, EA3500.did they remove the option ?
View 1 Replies
View Related
Apr 21, 2013
My E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies
View Related
Aug 14, 2012
The wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
View 5 Replies
View Related
Oct 11, 2012
I have experienced some strange behavior of WiFi connection using WRT320N router. ISP provides me the internet in 2 modes (day and night). During day mode max speed is 24 Mb/s and during night 60 MB/s. Modem ADSL (Cisco EPC3010) is connected to Linksys WRT320N and on router is configured WiFi.Now issue. In the day mode everything is perfect. Cable connection gives me 24 MB/s and WiFi connection around 22 MB/s so not so bad. However when my internet speeds up to 60 Mb/s (cable connection via router gives exactly 60), WiFi connection instead speed up as well, just drop to max 17 Mb/s. I have tied several different settings on the router including changes in WiFi band, channel width, different channels (now channel is setup to 1 which is maybe not totally free but no so occupied) and others but unfortunately without significant improvement (in many cases connection just slowed down more).
And some details:
Wireless configuration (now)
Band: 2.4GHz
Mode: Wireless-N only
Channel Width: Auto (20MHz or 40 MHz)
Channel: 1
Wireless adaptor: Intel Centrino Advanced-N 6230 (I know that this doesn’t mean anything but Win7 shows that connection is established with speed 144MB/s)Router firmware and WiFi card updated to the newest version.
View 9 Replies
View Related
Apr 8, 2012
I installed this Linksys E1500 yesterday and have had a problem keeping my iPhone 4 and an iPod Touch connected to WiFi.The devices go to sleep. When I swipe the screen and "bring them back" the WiFi is Not Connected. I have to go in and re-enter my network password again. As long as the devices don't go to sleep, they maintain connectivity. Once connected they function properly.
The iPad 2 & Samsung Galaxy S phone we have seem to be keeping their WiFi connectivity, as well as a G62 HP laptop running Windows 7, an older XP machine using a Cisco AE1000 wireless network adaptor and the Xbox 360. The issue is just with the iPhone 4(ios 5) and the iPod Touch(ios 4).
I had issues with the iPad and the Galaxy phone until i disabled WMM Support in App & Gaming.I would bring this back to the retailer but I had it sitting on my desk for about 30 days and it's past their return policy.The firmware is up to date on the Router. I've tried power cycling all the devices including the cable modem & the new router.
View 1 Replies
View Related
Nov 23, 2010
I was trying to remotely command my iTunes library via an iPhone app called Remote. It worked for some times with an intermittent disconnection problem due to the iPhone locking. But even after unlocking the phone and reconnecting the Wi-Fi, Remote couldn't find my iTunes library again and my only workaround was to relaunch iTunes on the PC (which is Ethernet-wired to my router). Few days ago nothing worked!!! I could no more get Remote to find iTunes.
I could not find a solution even by rebooting the router or unplugging the PC's Ethernet cable. Last night I powered off the router and after 10s I powered it on again. And then it worked!I highly suspect a problem between my router and Bonjour which is as UPnP, an Apple protocol for discovering communicating devices. Discovery phase being usually done with broadcast frames, something goes wrong in the router with processing the broadcasts, or is it a Bonjour problem?Please note that even now that Remote can find iTunes, I still have my old intermittent disconnection problem.So is there any incompatibility between WRT-610N and Bonjour and what is the fix ?
View 3 Replies
View Related
Jun 30, 2011
Our network is being handled by a SonicWall Firewall. How do I find the IP address of the wireless router connected to the network switch. I am trying to reset the password of the wireless router.
View 11 Replies
View Related
May 27, 2011
I have Comcast cable internet routed through a linksys E3000 router. My desktop is connected to my router via ethernet and my various other devices including my laptop are wifi connected. It seems almost at random that my desktop will lose its connection.Windows will show me as still being connected and my network connection will show a normal status until I atttempt to repair it then it will change to limited or no connectivity. Through all of this, my other devices all still have a wifi signal (I don't use more than 1 or 2 at the same time). I can reconnect to the internet by unplugging my ethernet cable then reuplugging it back in and my connection will start working again. I've also had several blue screens, and when I checked the dmp files it revealed my network card driver as the culprit, yet I have reinstalled and even clean installed the microsoft signed driver. I have also attempted to reboot both my modem and router to no avail.
Microsoft XP
Marvell Yukon ethernet adapter on a biostar mobo
C:Documents and SettingsMain>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : sn1
Primary Dns Suffix . . . . . . . :
[code]...
View 5 Replies
View Related
Jan 29, 2011
I've been having major issues with my wireless on this computer (randomly decides not to work while computers in the same room are fine) so I got a new wireless card to see what it could do. Installed it, everything says it's installed fine, but it will NOT detect any wireless networks. Not just mine, any of the 8+ networks I can usually detect from my room. I'm on Win7 Professional 64.
Things I've tried (and I'll be seriously annoyed if people reccomend doing them a 14th time, as I've already spent an hour on livechat with a support person telling me to do things I told her I'd already done):
Installed with 4 different drivers (the ones on the CD, the ones on the website, two versions directly from Ralink for the chipset) Tried both the manual and automatic "update driver" options in device manager. Uninstalled/reinstalled it like 4 times. Moved it to a new PCI slot.
Removed the old adapter before installing it. Removed the old adapter after installing it. Tried connecting to my network as a "hidden" network (which it's not). Installed only the driver and not the adapter utility, and used the utility. Installed the software before physically installing the adapter. Installed it after physically installing the adapter.
I'm at a loss. It doesn't detect ANY networks. No, it's not a problem with my network, there's more than a half dozen that my other adapter, in the same computer, can detect. And I don't know why. It has not ever worked properly. The antennae are on properly, nothing is interfering with it (though that would be odd since it's 3 inches from an adapter that can detect other networks). I might be willing to accept that it's just DoA, but that would be odd considering it installs just fine and reports that it's working just fine.
View 2 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Jan 28, 2012
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies
View Related
Nov 3, 2011
E2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies
View Related
