On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 RepliesI am trying to scan a directv device that is connected on my lan it uses port 8080. My hardwired machine returns the expected data, any call from a device connected via my wireless network returns a page can not be displayed. It appears as if the router is blocking ports 8080 over wifi only.
View 4 Replies View RelatedI cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies View RelatedI've just updated my router (E4200v2) to the smart wi-fi firmware and it seems I can only properly access it in the "local" mode (by that I mean that I can edit some of the properties such as wifi settings).If I try to login through the cloud / smart wifi account i only get the empty screen, no options, no widgets, nothing (see the included picture).
View 5 Replies View RelatedI've noticed that my E4200v2 Smart-Wifi cloud doesn't show all the devices that are connected to my router.To test, last night we turned on EVERYTHING....4 iPod Touches, 2 Xbox's, 1 Blu-ray player connected to Netflix, 1 Directly receiver, 4 laptops,1 desktop,1 iPhone, and made sure all of them were connected to the Wi-fi and actually streaming / downloading/playing something the Smart WiFi only recognized about half of them as being connected. I rebooted the router and it picked up a few more but never accounted for all the devices connected.
If you can't account for all the devices connected to your network, setting-up up reliable Parental Controls is almost impossible.Very disappointed and about ready to start looking for another brand of router. Sad, as I've been with Cisco/Linksys for over a decade and been very satisfied in the past.
I just found a slightly unsettling bug in the E4200v2 (running the latest firmware 2.0.36 build 126507).Administration > Local Management Access > Access via Wireless ... set to DISABLED. HOWEVER, when I attempted to access the web interface on a handy iPAD I had absolutely no problem getting through to the web interface (after providing username and passsword).Limiting access to wired clients seems like a simple a prudent measure ... which is why this option is there for the paranoid among us.This seems like a black-and-white bug.
View 9 Replies View RelatedIs there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies View RelatedMy E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies View RelatedThe wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
I have experienced some strange behavior of WiFi connection using WRT320N router. ISP provides me the internet in 2 modes (day and night). During day mode max speed is 24 Mb/s and during night 60 MB/s. Modem ADSL (Cisco EPC3010) is connected to Linksys WRT320N and on router is configured WiFi.Now issue. In the day mode everything is perfect. Cable connection gives me 24 MB/s and WiFi connection around 22 MB/s so not so bad. However when my internet speeds up to 60 Mb/s (cable connection via router gives exactly 60), WiFi connection instead speed up as well, just drop to max 17 Mb/s. I have tied several different settings on the router including changes in WiFi band, channel width, different channels (now channel is setup to 1 which is maybe not totally free but no so occupied) and others but unfortunately without significant improvement (in many cases connection just slowed down more).
And some details:
Wireless configuration (now)
Band: 2.4GHz
Mode: Wireless-N only
Channel Width: Auto (20MHz or 40 MHz)
Channel: 1
Wireless adaptor: Intel Centrino Advanced-N 6230 (I know that this doesn’t mean anything but Win7 shows that connection is established with speed 144MB/s)Router firmware and WiFi card updated to the newest version.
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
I installed this Linksys E1500 yesterday and have had a problem keeping my iPhone 4 and an iPod Touch connected to WiFi.The devices go to sleep. When I swipe the screen and "bring them back" the WiFi is Not Connected. I have to go in and re-enter my network password again. As long as the devices don't go to sleep, they maintain connectivity. Once connected they function properly.
The iPad 2 & Samsung Galaxy S phone we have seem to be keeping their WiFi connectivity, as well as a G62 HP laptop running Windows 7, an older XP machine using a Cisco AE1000 wireless network adaptor and the Xbox 360. The issue is just with the iPhone 4(ios 5) and the iPod Touch(ios 4).
I had issues with the iPad and the Galaxy phone until i disabled WMM Support in App & Gaming.I would bring this back to the retailer but I had it sitting on my desk for about 30 days and it's past their return policy.The firmware is up to date on the Router. I've tried power cycling all the devices including the cable modem & the new router.
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies View RelatedRecieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies View Relatedthis topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies View RelatedJust got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies View RelatedI will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies View RelatedI have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies View RelatedWe have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies View RelatedI have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies View RelatedV2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies View RelatedMy ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies View RelatedE4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies View Related I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies View RelatedWhere can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies View RelatedI purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies View RelatedNo problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies View RelatedMy Linksys E4200v2 router died (no blinking lights when a network cable is attached). Is this a bait and switch?
View 2 Replies View RelatedI recently changed my wirless router from the E4200 to the E4200v2. As far as I know, I have the same settings on the E4200v2 as I did on the E4200. My PS3 will not connect to my wireless network via the E4200v2. I even retyped in my network information (SSID and password) onto the PS3. Still "no joy." Any issue with the E4200v2 and the PS3?
View 9 Replies View RelatedI have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies View Related