Linksys Wireless Router :: E4200v2 And Port 8080 Over Wifi
May 27, 2012
I am trying to scan a directv device that is connected on my lan it uses port 8080. My hardwired machine returns the expected data, any call from a device connected via my wireless network returns a page can not be displayed. It appears as if the router is blocking ports 8080 over wifi only.
View 4 Replies
ADVERTISEMENT
Aug 17, 2011
I own an E4200 and my wife and I use Goodreader on our ipads at home. To add docs to goodreader we need to connect to the ipads ip on port 8080 but the E4200 is blocking all traffic for it. How can I open port 8080 for our 2 ipads?
View 1 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Jul 5, 2012
I cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies
View Related
Mar 18, 2013
I've just updated my router (E4200v2) to the smart wi-fi firmware and it seems I can only properly access it in the "local" mode (by that I mean that I can edit some of the properties such as wifi settings).If I try to login through the cloud / smart wifi account i only get the empty screen, no options, no widgets, nothing (see the included picture).
View 5 Replies
View Related
Jan 8, 2013
I've noticed that my E4200v2 Smart-Wifi cloud doesn't show all the devices that are connected to my router.To test, last night we turned on EVERYTHING....4 iPod Touches, 2 Xbox's, 1 Blu-ray player connected to Netflix, 1 Directly receiver, 4 laptops,1 desktop,1 iPhone, and made sure all of them were connected to the Wi-fi and actually streaming / downloading/playing something the Smart WiFi only recognized about half of them as being connected. I rebooted the router and it picked up a few more but never accounted for all the devices connected.
If you can't account for all the devices connected to your network, setting-up up reliable Parental Controls is almost impossible.Very disappointed and about ready to start looking for another brand of router. Sad, as I've been with Cisco/Linksys for over a decade and been very satisfied in the past.
View 3 Replies
View Related
Jan 21, 2012
I just found a slightly unsettling bug in the E4200v2 (running the latest firmware 2.0.36 build 126507).Administration > Local Management Access > Access via Wireless ... set to DISABLED. HOWEVER, when I attempted to access the web interface on a handy iPAD I had absolutely no problem getting through to the web interface (after providing username and passsword).Limiting access to wired clients seems like a simple a prudent measure ... which is why this option is there for the paranoid among us.This seems like a black-and-white bug.
View 9 Replies
View Related
Dec 27, 2012
Is there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies
View Related
Feb 23, 2011
how do I block / unblock ports in ASA Firewall 5500 series?
View 2 Replies
View Related
May 23, 2011
I'm trying to develop and test a website from my iPad. I have my laptop and iPad on same local network, 192.168.1.xThey can see each other over network and I can access the page:192.168.1.105:80 (my laptops local web server) from both iPad and laptop. However the application server runs on port 8080 and I cannot access this from either device/machine. the router's firewall is playing a role, and I have no software firewall running on laptop that I'm aware of (turned off windows 7 firewall).localhost:8080/myWebSite or 127.0.0.1 also works on port 8080.The only combo that does not work is 192.168.1.105 with port 8080. I need this so the iPad can hit the site so I can test locally while developing.
View 4 Replies
View Related
Sep 5, 2012
wondering if redirection or conversion port 8080 into port 80 is possible? if so how and what cisco equipment can do that?
View 11 Replies
View Related
Feb 27, 2013
I need to redirect all http and https traffic from one source in a dmz network, to port tcp/8080 on a proxy server on the inside network.
The source device doesn't handle proxying very well, so i've been advised to redirect the tcp/80 and tcp/443 ports to tcp/8080 as it passes through the firewall.
Scenario is thus:
PIX 515E 6.3 (5)
DMZ server: 172.31.255.250 (Real IP), 10.44.181.236 (NAT IP)
Inside Proxy server: 10.44.132.28 (Real IP), 172.31.255.110 (NAT IP)
I've configured a static NAT redirect using the following command: static (inside,dmz) tcp 172.31.255.110 www 10.44.132.28 8080 netmask 255.255.255.255 0 0
When I try to add the next command of: static (inside,dmz) tcp 172.31.255.110 443 10.44.132.28 8080 netmask 255.255.255.255 0 0
I get the following error: ERROR: duplicate of existing static
Is there a work around for this at all or am I stuck with the limitations of the software?
View 2 Replies
View Related
Jan 5, 2012
I have a cisco 1841 and I am hooking up some cameras onto my network. My global IP is 64.190.170.2 and my internal IP which is going to my cameras DVR is 192.168.1.15. I need to be able to forward port 8080 from my global IP to my local IP so i can view my DVR remotely. What is the command i need to put in my Cisco 1841 to forward this port?
View 2 Replies
View Related
Mar 21, 2012
I've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies
View Related
Jun 29, 2012
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies
View Related
Mar 16, 2012
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies
View Related
Mar 28, 2012
this topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies
View Related
Apr 21, 2012
Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 29, 2012
I have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies
View Related
Aug 18, 2011
I have just upgraded my Linksys router from an older one to the E-2500 about a week ago. Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers. I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan. Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.
I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.
I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.
View 1 Replies
View Related
Feb 29, 2012
We have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies
View Related
Jan 11, 2013
I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies
View Related
Dec 14, 2011
V2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies
View Related
Dec 20, 2012
My ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies
View Related
Dec 23, 2011
E4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies
View Related
Aug 16, 2012
I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
View 6 Replies
View Related
Feb 24, 2013
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies
View Related
Jan 23, 2012
Where can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies
View Related
Aug 1, 2012
I purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies
View Related
Jan 31, 2012
No problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
View 2 Replies
View Related
Apr 24, 2012
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
View 2 Replies
View Related
Feb 24, 2013
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies
View Related