Linksys Wireless Router :: E4200v2 Local Management Access Via Wifi
Jan 21, 2012
I just found a slightly unsettling bug in the E4200v2 (running the latest firmware 2.0.36 build 126507).Administration > Local Management Access > Access via Wireless ... set to DISABLED. HOWEVER, when I attempted to access the web interface on a handy iPAD I had absolutely no problem getting through to the web interface (after providing username and passsword).Limiting access to wired clients seems like a simple a prudent measure ... which is why this option is there for the paranoid among us.This seems like a black-and-white bug.
View 9 Replies
ADVERTISEMENT
Jul 19, 2012
I am using an E2500 as an access point, which is working fine. I have an Ethernet cable on one of the LAN ports of the E2500 connected to a LAN port on my gateway router. The LAN address of the E2500 is 192.168.7.3 and the LAN address of the gateway router is 192.168.7.1. Clients on the E2500 wireless network have no problems getting to the Internet through the gateway router. Clients on the E2500 wireless network can reach the E2500 local management port at 192.168.7.3 on port 80. On the gateway router I am forwarding WAN port 8083 to LAN address 192.168.7.3 at port 80. But I cannot access the E2500 local management interface via the gateway router. The E2500 should see the request as from 192.168.3.1 due to NAT in the gateway router, right? I can reach any of my actual access points this way, just not a router being used as an access point. Security/design limitation of the router?
View 2 Replies
View Related
Mar 30, 2012
I have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
May 6, 2012
How to get HTTPS to work for local or remote management? Selecting HTTPS for either local or remote doesn't enable HTTPS for me. It still use HTTP.
View 2 Replies
View Related
May 27, 2012
I am trying to scan a directv device that is connected on my lan it uses port 8080. My hardwired machine returns the expected data, any call from a device connected via my wireless network returns a page can not be displayed. It appears as if the router is blocking ports 8080 over wifi only.
View 4 Replies
View Related
Jul 5, 2012
I cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies
View Related
Mar 18, 2013
I've just updated my router (E4200v2) to the smart wi-fi firmware and it seems I can only properly access it in the "local" mode (by that I mean that I can edit some of the properties such as wifi settings).If I try to login through the cloud / smart wifi account i only get the empty screen, no options, no widgets, nothing (see the included picture).
View 5 Replies
View Related
Jan 8, 2013
I've noticed that my E4200v2 Smart-Wifi cloud doesn't show all the devices that are connected to my router.To test, last night we turned on EVERYTHING....4 iPod Touches, 2 Xbox's, 1 Blu-ray player connected to Netflix, 1 Directly receiver, 4 laptops,1 desktop,1 iPhone, and made sure all of them were connected to the Wi-fi and actually streaming / downloading/playing something the Smart WiFi only recognized about half of them as being connected. I rebooted the router and it picked up a few more but never accounted for all the devices connected.
If you can't account for all the devices connected to your network, setting-up up reliable Parental Controls is almost impossible.Very disappointed and about ready to start looking for another brand of router. Sad, as I've been with Cisco/Linksys for over a decade and been very satisfied in the past.
View 3 Replies
View Related
Dec 27, 2012
Is there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies
View Related
Mar 5, 2013
I'm having some difficulty getting into the settings web page on my e4200 router while the modem is running. I can access it soon as the modem is turned off. Additionally I downloaded the Android cisco express connect app for my tablet which does allow me to access the router while the modem is switched on.
View 5 Replies
View Related
Jan 19, 2013
I have an E4200 V2. The 2.4ghz and 5ghz bands are both enabled and named differently. From what I've read they should both show up in the list of networks when I'm connecting other computers etc? All I'm getting is the 2.4ghz.Everything on the router is working fine as far as I can tell, just can't seem to access the 5ghz band. Maybe I recently upgraded to the Smart WiFi firmware but it's the same situation.The two bands have the same password with two of the first three letters switched on one.
View 3 Replies
View Related
Dec 18, 2012
I have the e4200v2 with Smart Wifi (formerly Connect Cloud). On my previous routers, I've been able to shut down internet access for my ENTIRE home network at a specific time each night and then re-allow access again at a specfic time the next morning.
In using the Parental Controls on the 4200v2, it appears I have to set times for EACH and EVERY device on my network. I have 4 kids and a very heavy wireless network, including 3 Xboxes, 1 PS3, a Bluray player, a Directv receiver, an RCA media streaming device, 4 laptops, 1 desktop, 4 IPODs, and 1 IPhone on my network.
My goal is to shut down the internet access completely each night at Midnight, then re-allow access the next morning at 6am in order to ensure my kids aren't up all night playing games, etc. But the the Parental Controls on the 4200v2, it appears I have to do this for EVERY device, instead of being able to just shut down access across the board like I could with the old Linksys web-based interface.
View 9 Replies
View Related
Feb 5, 2012
I just upgraded my old WRT54G to a E4200v2 with firmware 2.0.36.126507. I installed it using the Cisco Connect CD. At first it seemed OK, but then I noted that I cannot open (or takes forever) many websites, in particular those requiring Adobe Flash Player to view. In addition, it appears that access IPv6 Internet or sites is impossible, even though IPv6 is enabled in the GUI. Is there anything I am missing in the configuration/set up of the router?
View 9 Replies
View Related
Dec 11, 2012
I am using a Linksys E4200V2 for my routing needs. I have 6 hardwired connections and 9 wireless connections. Due to my hardwired connections all going into one corner of my basement my router is placed there. When I had an E3000 my wireless coverage was fairly acceptable. After a power surge took out a bunch of stuff (which I have remedied with a whole home surge protector and better surge protectors for my devices) my E4200 replacement just doesn't have as good of coverage, especially in our office. This renders wireless to our phones/tablet useless in there (wife's laptop and my desktop are hard wired when in the office). I have a fairly large home so no wireless router is going to give me great coverage in my office, which is furthest from my router and has a bunch of obstructions to go through.I want to do an access point. I tried with an old Belkin Wireless G router, but it is only working when it wants to and there is probably a reason I stuff it in a box years ago. Of course I gave my other working Netgear N-router to my mom...so I'm out of wireless routers.
I want to buy something that:
- Is under $50
- Can do dual-band wireless N
- If it has Gigabit Ethernet ports that would be sweet as I could make use of them, but I can live without
- Can either repeat the wireless signal from my Linksys or be hard-wired as I have Ethernet connections all over my home. I'd suspect there would be a performance benefit from a hard wired unit.
Usage - from a hardwired perspective, I do some heavy LAN file transfers and high-bandwidth streaming on a semi-regular basis. For wireless, some random downloading (nothing time urgent), surfing and video streaming off the web is about it, and Airplay from our iOS devices (iOS stuff is only Apple stuff we have, rest is Win 7/8 and Android) with Apple TV being hardwired.
View 1 Replies
View Related
Nov 19, 2011
I have a Linksys WAG200G, I only use it for 2 devices a Win 7 PC and an iPad.
Surfing the net is fine, I'm get an average of 30ms when I ping to my local ISP.
But when I try to stream music or movies from my PC to iPad via iTunes, it starts playing for a couple of seconds then it stops, and then it will start again for a few more seconds. I tried pinging from PC to iPad and get a range from 400ms-2500ms.
I'm not sure which settings I need to adjust to make it work correctly.
View 3 Replies
View Related
Aug 14, 2012
I have a Linksys E2000 router. I am trying to install an Epson NX230 printer on my home network. Apparently, the Epson printer has a MAC address assigned to it. My network cannot find the printer. I looked at my riuter setup and the MAC Address Clone has two buttons, Enabled Disabled. The Disabled button is clicked on. Accdording to documentation I foudn on this website, it looks like I can Enabled the MAC Address clone button. The document also mentgioend entereding the MAC address for a PC.
If I enable the MAC Address Clone, do I enter the MAC address for the printer or during the install process does the MAC address get installed also
View 9 Replies
View Related
Aug 23, 2011
I cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.
View 7 Replies
View Related
Aug 24, 2011
I just purchased a new linksys e1500 and followed the steps on the cd to set it up. I have internet access on my windows 7 laptop and iphone however, I have "local access only" on the two laptops we have running vista. The router is working fine for the windows 7 machine and the iphone but I cannot connect to the internet on the two vista machines.
View 9 Replies
View Related
Jun 23, 2012
I have some issue with internet connection and Router WRT54G. There is always "Local Connection" but no internet access. I checked that at two different laptops. One with Windows Vista and the other one with Windows XP. Both the same problem. There is a wireless connection with excellent signal strength but no internet access. I added a screen shut to see the Router setting. If more needed I will add more.
View 6 Replies
View Related
Dec 25, 2011
The issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies
View Related
Jan 22, 2012
I upgraded my old Linksys wrt54g to the E1500. All the XP os are connected via cable and wireless connection, but the Vista laptop i get local access only connection error. This laptop used to connect on the older router using wep but with E1500 wpa-2 it cannot connect. I am unable to ping the router from the laptop wireless. Connecting ethernet cable it works fine and logging in as a guest works does too.
View 1 Replies
View Related
Oct 3, 2012
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
View 1 Replies
View Related
Jun 24, 2012
I am using 3945E Router as Easy VPN Server, with 15.1 IOS. On router I have bunch on usernames for VPN authentication, I want to restrict Router management access for them(ssh,telnet, http and so on).
View 2 Replies
View Related
Apr 22, 2012
i'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies
View Related
Sep 7, 2012
I have an EA2700 running latest firmware 1.1.38.138827. It is using Cisco Connect Cloud. I am unable to access the DHCP Reservations link under Connectivity/ Local Network. When I click on it, nothing happens. I've tried multiple browsers including IE 10 (Windows 8 RTM), Firefox 15, and Chrome 21. I also tried on a Windows 7 machine with IE 9 and the link doesn't work on that either except that it shows a box that says Invalid Character when I click on the DHCP Reservations link. I see no invalid characters on the screen. Any workaround other than downgrading the firmware or assigning static IPs on individual PCs?Also, on an unrelated note, where is the Dynanic DNS configuration on the Cisco Connect Cloud?
View 8 Replies
View Related
Jun 29, 2012
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies
View Related
Mar 16, 2012
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies
View Related
Mar 28, 2012
this topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies
View Related
Apr 21, 2012
Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 29, 2012
I have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies
View Related
Feb 29, 2012
We have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies
View Related
