Linksys Wireless Router :: E4200v2 Cannot Access IPv6 Internet Or Sites?
Feb 5, 2012
I just upgraded my old WRT54G to a E4200v2 with firmware 2.0.36.126507. I installed it using the Cisco Connect CD. At first it seemed OK, but then I noted that I cannot open (or takes forever) many websites, in particular those requiring Adobe Flash Player to view. In addition, it appears that access IPv6 Internet or sites is impossible, even though IPv6 is enabled in the GUI. Is there anything I am missing in the configuration/set up of the router?
View 9 Replies
ADVERTISEMENT
Dec 18, 2012
I have the e4200v2 with Smart Wifi (formerly Connect Cloud). On my previous routers, I've been able to shut down internet access for my ENTIRE home network at a specific time each night and then re-allow access again at a specfic time the next morning.
In using the Parental Controls on the 4200v2, it appears I have to set times for EACH and EVERY device on my network. I have 4 kids and a very heavy wireless network, including 3 Xboxes, 1 PS3, a Bluray player, a Directv receiver, an RCA media streaming device, 4 laptops, 1 desktop, 4 IPODs, and 1 IPhone on my network.
My goal is to shut down the internet access completely each night at Midnight, then re-allow access the next morning at 6am in order to ensure my kids aren't up all night playing games, etc. But the the Parental Controls on the 4200v2, it appears I have to do this for EVERY device, instead of being able to just shut down access across the board like I could with the old Linksys web-based interface.
View 9 Replies
View Related
Mar 5, 2013
I'm having some difficulty getting into the settings web page on my e4200 router while the modem is running. I can access it soon as the modem is turned off. Additionally I downloaded the Android cisco express connect app for my tablet which does allow me to access the router while the modem is switched on.
View 5 Replies
View Related
Jan 19, 2013
I have an E4200 V2. The 2.4ghz and 5ghz bands are both enabled and named differently. From what I've read they should both show up in the list of networks when I'm connecting other computers etc? All I'm getting is the 2.4ghz.Everything on the router is working fine as far as I can tell, just can't seem to access the 5ghz band. Maybe I recently upgraded to the Smart WiFi firmware but it's the same situation.The two bands have the same password with two of the first three letters switched on one.
View 3 Replies
View Related
Jan 21, 2012
I just found a slightly unsettling bug in the E4200v2 (running the latest firmware 2.0.36 build 126507).Administration > Local Management Access > Access via Wireless ... set to DISABLED. HOWEVER, when I attempted to access the web interface on a handy iPAD I had absolutely no problem getting through to the web interface (after providing username and passsword).Limiting access to wired clients seems like a simple a prudent measure ... which is why this option is there for the paranoid among us.This seems like a black-and-white bug.
View 9 Replies
View Related
Jan 31, 2012
No problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
View 2 Replies
View Related
Nov 14, 2011
My own sites were down & I can't view them on my computer now.This is the 2nd time this has happened to me with router WRT54G.Every time there's a problem with my hosting company & my sites go down, my router blocks them once the sites are back up & running.When I plug directly into the modem I can access them, but then I can't use my phone, etc.I've recycled & I keep trying to find how you save your settings on your router so I can do a cold reboot, but I can't find the instructions anywhere.Why does it keep doing this & how to save the settings & restore them.
View 2 Replies
View Related
Aug 25, 2011
How do I restrict wireless user from accessing download sites that slow my network?
View 1 Replies
View Related
Dec 14, 2012
I am not able to access https sites (like banking etc.). Once I plug my old router back I have no such problem. I guess it must be router settings that I cannot figure out.
View 7 Replies
View Related
Apr 22, 2013
I'm having an intermittent issue with my E4200v2 router. Frequently I will be using a device on the wireless network, and it will be unable to reach the internet. Normally I would assume this was a problem with the cable modem, but disconnecting from and reconnecting to the router often fixes the problem.
View 9 Replies
View Related
Dec 11, 2012
I am using a Linksys E4200V2 for my routing needs. I have 6 hardwired connections and 9 wireless connections. Due to my hardwired connections all going into one corner of my basement my router is placed there. When I had an E3000 my wireless coverage was fairly acceptable. After a power surge took out a bunch of stuff (which I have remedied with a whole home surge protector and better surge protectors for my devices) my E4200 replacement just doesn't have as good of coverage, especially in our office. This renders wireless to our phones/tablet useless in there (wife's laptop and my desktop are hard wired when in the office). I have a fairly large home so no wireless router is going to give me great coverage in my office, which is furthest from my router and has a bunch of obstructions to go through.I want to do an access point. I tried with an old Belkin Wireless G router, but it is only working when it wants to and there is probably a reason I stuff it in a box years ago. Of course I gave my other working Netgear N-router to my mom...so I'm out of wireless routers.
I want to buy something that:
- Is under $50
- Can do dual-band wireless N
- If it has Gigabit Ethernet ports that would be sweet as I could make use of them, but I can live without
- Can either repeat the wireless signal from my Linksys or be hard-wired as I have Ethernet connections all over my home. I'd suspect there would be a performance benefit from a hard wired unit.
Usage - from a hardwired perspective, I do some heavy LAN file transfers and high-bandwidth streaming on a semi-regular basis. For wireless, some random downloading (nothing time urgent), surfing and video streaming off the web is about it, and Airplay from our iOS devices (iOS stuff is only Apple stuff we have, rest is Win 7/8 and Android) with Apple TV being hardwired.
View 1 Replies
View Related
Jan 15, 2013
I want to block sites like facebook during my workday but allow the rest of the internet.
The attached settings block facebook as desired during the filter times but after 6:30pm the filter expires and the entire internet is blocked (not just facebook). All of my browsers act as if they are hanging and won't load pages until I disable the filter.
I've also tried creating two different filters (one at a time). The first allowed full internet access all the time and the second allowed access the opposite times of the work filter. But to no avail.
View 2 Replies
View Related
Dec 20, 2012
how do I block IP/Internet Adresses for ALL users without adding the sites manually per user in the Parental Control panel? I want to block a certain IP/internet adress for all users but can't find this feature within my EA6500 anywhere?Is this a firmware bug? Has linskys forgotten that some sites want to blocked for all users and how do I do it all in one?
View 1 Replies
View Related
Jun 29, 2012
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies
View Related
Mar 16, 2012
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies
View Related
Mar 28, 2012
this topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies
View Related
Apr 21, 2012
Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 29, 2012
I have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies
View Related
Jul 8, 2012
MY ISP installed one router in my lab.for internet connectivity they mail me steps :connect your Laptop directly to gi0/3 port to check internet connectivity with public ip 1.1.1.x and Gateway 1.1.1.1 with subnet mask 255.255.255.240 after connection I surprised because I am able to access only google sites like gmail,google search etc. but I am able to ping/traceroute all sites.from browser I am able to access only google sites only.In Router no firewall no such access list.
View 2 Replies
View Related
Feb 29, 2012
We have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies
View Related
Jan 11, 2013
I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Dec 14, 2011
V2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies
View Related
Dec 20, 2012
My ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies
View Related
Dec 23, 2011
E4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies
View Related
Aug 16, 2012
I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
View 6 Replies
View Related
Feb 24, 2013
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies
View Related
Jan 23, 2012
Where can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies
View Related
Aug 1, 2012
I purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies
View Related
Apr 24, 2012
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
View 2 Replies
View Related
Feb 24, 2013
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies
View Related
Jul 24, 2012
My Linksys E4200v2 router died (no blinking lights when a network cable is attached). Is this a bait and switch?
View 2 Replies
View Related
