Linksys Wireless Router :: E4200V2 SPI Blocks FTP From The Internet?
Jan 31, 2012
No problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
View 2 Replies
ADVERTISEMENT
Dec 18, 2012
I have the e4200v2 with Smart Wifi (formerly Connect Cloud). On my previous routers, I've been able to shut down internet access for my ENTIRE home network at a specific time each night and then re-allow access again at a specfic time the next morning.
In using the Parental Controls on the 4200v2, it appears I have to set times for EACH and EVERY device on my network. I have 4 kids and a very heavy wireless network, including 3 Xboxes, 1 PS3, a Bluray player, a Directv receiver, an RCA media streaming device, 4 laptops, 1 desktop, 4 IPODs, and 1 IPhone on my network.
My goal is to shut down the internet access completely each night at Midnight, then re-allow access the next morning at 6am in order to ensure my kids aren't up all night playing games, etc. But the the Parental Controls on the 4200v2, it appears I have to do this for EVERY device, instead of being able to just shut down access across the board like I could with the old Linksys web-based interface.
View 9 Replies
View Related
Feb 5, 2012
I just upgraded my old WRT54G to a E4200v2 with firmware 2.0.36.126507. I installed it using the Cisco Connect CD. At first it seemed OK, but then I noted that I cannot open (or takes forever) many websites, in particular those requiring Adobe Flash Player to view. In addition, it appears that access IPv6 Internet or sites is impossible, even though IPv6 is enabled in the GUI. Is there anything I am missing in the configuration/set up of the router?
View 9 Replies
View Related
Apr 22, 2013
I'm having an intermittent issue with my E4200v2 router. Frequently I will be using a device on the wireless network, and it will be unable to reach the internet. Normally I would assume this was a problem with the cable modem, but disconnecting from and reconnecting to the router often fixes the problem.
View 9 Replies
View Related
Aug 19, 2012
I have a Linksys WRT310N V2 wireless router. Last week it started blocking access to our family website. That website appears to be the only one that is blocked. Every other website we have tried works just fine. I have tried the following.Remove the WRT310N router and plug a computer directly into the broadband modem. After this everything works fine for the one computer I have hooked into the internet.Remove the WRT310N router and substitute an old Linksys non-wireless router. Everything works fine for the hardwired computers on the LAN. Again, not really an option, need wireless access.
Unplug the router and so a soft reset. Still blocks this one website.I have not done a hard reset to factory specs. I wasn't looking forward to redoing everything I had set up.I looked over every setting in this router and can't find anything that would cause it to block a web page. I am far from a networking expert, but most of the settings seem pretty obvious.
View 3 Replies
View Related
Mar 4, 2013
i have router lynksys WRT120N and the latest 1.0.0.7 firmware. And the problem occured frequently. At about 13.00 i went out, wifi was working okay. At around 18.00 i returned home and i was trying to connect to the wifi with my android phone, and suprisingly it did not work. I tried on my laptop and on a android tablet. It did not work. The only thing that i could figure it out is to reset the router. I checked the settings, and there was no access policy e.g. time based access blocking.
View 5 Replies
View Related
Feb 19, 2012
ATT Uverse modem provides internet for the house. Uverse modem also includes a wifi router. The HP C410a printer is connected wirelessly to the Uverse router. The printer is able to access the internet, and all computers (including the problem Mac) can print wirelessly when wirelessly connected to the Uverse router. The Mac sits at the opposite end of the house, far outside the range of the Uverse router. To solve this, we have a Netgear Powerline adapter connected to the Uverse router to provide internet over powerlines throughout the house. At the opposite end of the house, the Linksys E1000 is connected by ethernet to the Netgear Powerline outlet. This setup works - all computers, including the Mac, can wirelessly connect to the E1000 and there is fast internet access.
Two different PC's can print wirelessly to the HP C410a while connected to the E1000 - it works perfectly. However, the Mac can't print via the E1000 - I have to carry the Mac over to be in range of the Uverse router and then print. When you try to print on the Mac, it can't "find" the printer. However, if I open the HP print utility on the Mac and manually enter the IP address of the printer, a new printer pops up and I can make it print test pages. But I still can't print anything else from the Mac.
The Mac can print if the E1000 is bypassed with a physical ethernet connection to the Powerline outlet. So the conflict is definitely between the E1000 and the Mac, because everything else works in every other combination.I think something in the E1000 is preventing the print driver on the Mac from sending data to the printer, because the Mac can "communicate" with the printer via the HP print utility software, but whenever you try to print using the driver it can't connect to the printer. I disabled the E1000 firewall
View 2 Replies
View Related
Sep 2, 2011
I have a blog and website hosted by X9 Hosting. I am unable to connect to cPanel, the website, the blog, or and X9 sites.This began when saving a WordPress article in the blog. The save hung and then all connectivity through the router was lost.When using the modem (wired) I can visit the above sites. what do I need to do to gain wireless connectivity back?
View 7 Replies
View Related
Jun 29, 2012
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies
View Related
Mar 16, 2012
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies
View Related
Mar 28, 2012
this topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies
View Related
Apr 21, 2012
Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 29, 2012
I have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies
View Related
Feb 29, 2012
We have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies
View Related
Jan 11, 2013
I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Dec 14, 2011
V2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies
View Related
Dec 20, 2012
My ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies
View Related
Dec 23, 2011
E4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies
View Related
Aug 16, 2012
I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
View 6 Replies
View Related
Feb 24, 2013
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies
View Related
Jan 23, 2012
Where can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies
View Related
Aug 1, 2012
I purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies
View Related
Apr 24, 2012
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
View 2 Replies
View Related
Feb 24, 2013
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies
View Related
Jul 24, 2012
My Linksys E4200v2 router died (no blinking lights when a network cable is attached). Is this a bait and switch?
View 2 Replies
View Related
Feb 11, 2012
I recently changed my wirless router from the E4200 to the E4200v2. As far as I know, I have the same settings on the E4200v2 as I did on the E4200. My PS3 will not connect to my wireless network via the E4200v2. I even retyped in my network information (SSID and password) onto the PS3. Still "no joy." Any issue with the E4200v2 and the PS3?
View 9 Replies
View Related
Mar 30, 2012
I have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies
View Related
Dec 23, 2011
Decided to go with the e4200v2. 199.99 for a router 450 + 450 with a little extra features. very pricey but thought it would be worth it. I got it hooked up with no problems for the first 5 minutes. I have 35mbps down wired from the router and on the 2.4 and 5.0 ghz band about 25 feet from the router was getting just that!! no loss really. However after a few more speed test i noticed it was fluctuating very slow to fast. Also the 2.4ghz was only 144mbps. after getting in the router i changed the 2.4ghz to channel 6 and 5ghz to 153 and changed to 20mhz only on the 2.4 and 40mhz only on the 5.0ghz. Now all is doing well .
1. why am i not able to run the 2.4ghz on 40mhz? when set to auto i have a lot slower speed tests even know it is running on 20mhz only because I'm only getting 144mbps. I don't know why its not running 40mhz ? i don't know why i have to change it to 20mhz only why cant i leave it on auto and if i had a day with little interference it would switch to 40? when left on auto the speeds go down drastically
2. i notice that some channels are brutally slow on both bands. like 1.5mbps ? is this normal
3. is this even worth it if the 2.4 band is acting this way?
4. from insider i see that 5.0ghz only connects to two channels isn't suppose to be 3?
View 4 Replies
View Related
Apr 12, 2012
With other devices, including Cisco Aironet, I've saved a lot of time in the past by cloning the config from one WAP to another. This is for when I have to set up 2 or more WAP's on the same network, that share 98% of the same settings.I was wondering if anyone's ever tried to do this with Linksys devices, and in my case two E4200v2's in bridge-mode (WAP-only). Will it let you Restore a config that came from a different device? (same hardware version of course)Obviously I would change the hostname, devicename & IP address to make them unique. But the rest of the settings would basically stay the same.
I'm talking about E4200's that are being used as bridge-mode access points, and so typical router functions like DHCP server are disabled on both.
View 2 Replies
View Related
May 2, 2012
Have the E4200v2 router. Suddenly my wireless devices have slowed to a crawl. I mean slow. My Cisco Connect confirms that my wired download speed is 30-32 GB, but my two Android devices have slowed to ~500k. I might have changed something - just don't know. I know I'm desperate though.
View 1 Replies
View Related
Jan 13, 2013
I need to understand the USB interface.
View 4 Replies
View Related
