E4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies I have done this before on this exact model about a month ago, so it's still fresh in my mind on port forwarding. (note, I'm using firmware version: 1.0.00) I am running a windows 7 computer wirelessly using this router.What I do for port forwarding is type in router IP (192.168.2.1) in internet explorer, type in "default" as username and "admin" as password. I click the "applications and gaming" link which brings me to port range forwarding.
I fill in my port info, in this case a mine craft server running on 25565. I set up two of the same ports, different names both at the same port, one running TCP and the other UDP, when it worked previously the "both" option did not work correctly. (I used to have a private network that a buddy of mine set up a while back, and I doubt he remembers what to do and I don't know where the manual is to make a new one, searching the internet sends me spam of people asking questions.)
I read somewhere it may have something to do with DHCP server settings conflicting with my IP. My IPv4 address reads 192.168.2.100, and the DHCP settings says the same.
Im having a issue with that any of my computers without a wireless connection have been incapable of getting out on the internet with the new router that i got myself, i know the cables works etc, since they work perfectly fine with the old modem alone, but wont work at all with this unless on a computer with wireless connection
View 5 Replies View RelatedDoes Cisco 602 office connect AP working correctly with a 5508 controller? As cannot get it to work as having random problems. Ie I see the SSID broadcast on the AP, but no authentication messages for clients on the controller.I have the same configuration setup on a 1142 office extend access point and works fine.The other 602AP i have is seen by the controller, but will not even broadcast the SSID.
View 3 Replies View RelatedI just upload firmware1.0.1.10 on 2 WAP121. After the update and reboot, I was able to confirm the firmware version in the System Summary menu. The update is uneventful.However, the functions WDS Bridge and WorkGroup Bridge no longer works on two WAP121:
- For WDS Bridge, when I configure a Remote MAC Address with WPA Encryption and then I click on the Save button, nothing happens there. But it works well when I choose without Encryption.
- For WorkGroup Bridge, when I click on the Save button (even without changing the configuration), I have a message "Certificate file uploaded successfully" and another error message in the background: "error occured for query you send path . device.sync ... "
1.0.0.3 firmware is not available on your site, it is imposible for me to go back.
I own a wireless WRT54G, which has worked fine in the past. After setting up a new wireless network, I went to the router webpage to open some ports. The problem with the page loading is that it doesn't display correctly. No clickable text is displayed on the top of the page or the side bar, so I basically can't do anything whatsoever to configure it. I've tried loading it up in both Firefox and Internet Explorer, with IE saying the page loaded but with errors.
View 5 Replies View RelatedOk so our company has a VPN set up on our workstation laptops for employees to be able to connect to the office network from home.We use CISCO VPN CLIENT, and a pre-setting .pcf file to upload our vpn into the client. The settings are correct completely to allow the VPN to work from home. All of our older workstations (Latitude D510-D630's) work with Windows XP SP3 32b. Recently i purchased new laptops (Latitude E6410's) and have started issuing them out with Windows 7 Enterprise 64b.A couple employees from home cannot get their VPN to work correctly at home with the New Laptops. Their old laptops work fine with the VPN, but the new ones dont. They are running a Frontier DSL modem with wireless.The VPN connects just fine on the new laptops, but the problem is... Nothing works. Outlook does not connect, They cannot access any of our network shares or drives. And cannot use any of our company's software that requires our network access.
I tried uninstalling the the CISCO Client, and reinstalling it, No Go.I tried changing the MTU Settings on the client and network adapters and wireless adapters, No Go.And it seems to be just an ISSUE with employees trying to VPN through a dsl connection using the new laptops, where others with the new laptops can VPN in fine through a time warner connection. But remind you, their old laptops work fine.. which seems kind of odd to me.
I am user of Dell Inspiron 1545 and I have problem with Internet. Till yesterday everything just worked great, when I was turning on a wi fi, it always found a network I wanted to. Yesterday, the current has been cut of. (?) and I lost connection to internet. After current camer back, everyone got internet back, but not me. My wi fi is still finding almost all networks except one, the most important one.
View 1 Replies View RelatedE1550 not connecting to any Google related sites via Kindle Fire web application (Silk) in Kindle Fire. Other wireless devices working fine from E1550 and all apps in Fire connecting fine.
View 5 Replies View RelatedSince a couple of weeks I have a linksys EA6500. When I go to the device list to see which devices are online the device list is not displayig the correct data. I see devices online that are offline and also devices are offline that are at the moment online. When I try to delete a device that is offline in the list I get error 2315. I have that error in the local and cloud interface. The list has a frozen state from a particular moment.
When I reboot the router then all devices in the list have status offline and the device list stays that way. Nothing gets online anymore or will be added. When I reset the router to factory default all keeps working without problems for approximately 24 hours and after that the problem occurs again. The list freezes again and you are not able to delete a device.
I searched the forums but no one has this problem. I only can find a post that describes my problem but for them a reset worked. In my case a factory reset works also but the problem keeps coming back.
So i see tons of threads here and on google talking about dns issues with their linksys router but I never see a solution other than to locally change the dns servers on the client machine to prevent it from using the linksys router dns. My router is the WRT310Nv2 running the latest firmware but I see others are affected as well. url...My issue is this router continues to fail dns resolutions and I have to either reset it or tell my client machine not to use my router as a point of dns resolution.
1. Why is my router failing to resolve domains correctly?
2. Is there anyway to fix this from the router?
I have hardware version B1, firmware version 2.00NA and several computers (wired & wireless) with Vista & Win 7 x64 and a Brother HL1440 printer.When I print something it comes out scrambled, images missing or cut off, empty pages, etc. This same setup worked fine when it was directly into one computer, then shared on the network though windows sharing. The problem was that computer had to be running to print off the network. I got the dir655 since it had printer sharing but so far its not been of any luck.
View 5 Replies View RelatedI am trying to get the ACS 5.3 to work with NCS but cannot make it work correctly. url...But this does not show how the ACS referencing AD groups would work when determining which custom attributes to use.
On the ACS 5.3 i have set up the following .The ad is working and in Users and identity stores/External identity stores/Active Directory then my AD test works fine.I have set up the Users and Identity stores/Identity Groups with appropriate ip s.I have configured the Network Device Groups/Network Devices and AAA Clients with the ip address and Authenication optionsA.In Policy Elements/Authorisation and Permissions/device administration/shell profiles.I have creeated a shell profile called network shell pro which das a common tasks of def priv = 0 and max priv = 15
Now i can get into the NCS but i do not see any of the administration buttons on NCS - so this means the custom attributes are not working.i shouldnt need a user for this on the ACS as its using AD.
I have a problems with one SA520W.The LAN port don't work correctly. If i connect PC directly via ethernet cable (i try 2 different cable and 2 different PC) the DHCP don't assign an IP. If i reset to factory default and manual insert IP (192.168.75.1) don't work.
View 2 Replies View RelatedFirst off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies View RelatedRecieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies View Relatedthis topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies View RelatedJust got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies View RelatedI will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies View RelatedI have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies View RelatedWe have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies View RelatedI have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies View RelatedOn the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies View RelatedV2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies View RelatedMy ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies View Related I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies View RelatedWhere can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies View RelatedI purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies View RelatedNo problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies View Related