Cisco Firewall :: Redirect Http / Https To Port 8080 PIX 6.3?
Feb 27, 2013
I need to redirect all http and https traffic from one source in a dmz network, to port tcp/8080 on a proxy server on the inside network.
The source device doesn't handle proxying very well, so i've been advised to redirect the tcp/80 and tcp/443 ports to tcp/8080 as it passes through the firewall.
Scenario is thus:
PIX 515E 6.3 (5)
DMZ server: 172.31.255.250 (Real IP), 10.44.181.236 (NAT IP)
Inside Proxy server: 10.44.132.28 (Real IP), 172.31.255.110 (NAT IP)
I've configured a static NAT redirect using the following command: static (inside,dmz) tcp 172.31.255.110 www 10.44.132.28 8080 netmask 255.255.255.255 0 0
When I try to add the next command of: static (inside,dmz) tcp 172.31.255.110 443 10.44.132.28 8080 netmask 255.255.255.255 0 0
I get the following error: ERROR: duplicate of existing static
Is there a work around for this at all or am I stuck with the limitations of the software?
View 2 Replies
ADVERTISEMENT
Dec 20, 2010
Right now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?
View 18 Replies
View Related
Jul 14, 2011
I have got a Cisco router connected to a LAN and to the internet.I was wondering if I could nat https traffic from inside to internet to a local server (Proxy) on a given port for example tcp 8080.
int tunnel0
ip address 192.168.0.1 255.255.255.0
ip nat inside
int fa0/1
des internet connexion
ip address 41.x.x.x.x 255.255.255.248
ip nat outside
ip access-list extended Proxy_Redirect
permit tcp 192.168.0.0 0.0.0.255 any eq 443
View 1 Replies
View Related
Dec 21, 2011
Windows IIS server configured behind a Cisco ASA 5540 listening on port 443 currently. Access-list and static translation configured. I have been ask to redirect all port 80 calls to port 443 for this web site only at the firewall. I have suggested moving it behind our content switch with negative results. Can we do this at the firewall level? how to accomplish the redirect for a single site. 8.2.4 is current code
View 4 Replies
View Related
Feb 27, 2012
For a CSS with a SSL module (performing SSL termination) - is it possible to impliment a redirect on https URL to send to equivalent http URL.If my understanding is correct, the CSS will do SSL termination and then use an http content rule on the resultant http stream as it is recursively handled by the CSS ? This would mean that the SSL module has no way of seeing/acting on layer 5 and above data (i.e. picking up on a specific URL) and can not itself issue a redirect - i.e. you could not associate a redirect statement or service with the following ssl content rule ? [code]The CSS would instead rely on a http content rule to impliment a redirect - i.e. you would have to associate a redirect statement or service to the following http content rule instead?
But if the CSS is already handling traffic for existing url... traffic that is going to cause a loop when a client goes direct to. url...I realise the requirment is uncommon / a bit convoluted, its one of those don't ask type scenarios - aimed at achieving a specific requirement.Would the ACE 4710 be able to handle such a scenario any differently ?
View 7 Replies
View Related
Jun 21, 2012
I am trying to make a redirect from http to https. the goal is whenever a user writes in http://10.80.199.71 it should be redirected to https://10.80.199.71 I am just haveing some trouble making it work.
View 4 Replies
View Related
Feb 6, 2013
How to configure a redirection on the ACE from HTTP to HTTPS using specific URL example [URL] to [URL], the SSL certificates were installed on the servers.
View 7 Replies
View Related
Sep 12, 2011
how do I install Firefox if I cannot connect to the internet? Can I "save" it to a disc or flash drive from another computer.
View 7 Replies
View Related
Apr 25, 2011
i have the following scenario :
ISP1-------ASA 5510----------ISP2
|
|
|
LAN
i would like to use ISP2 for all http/https/ftp traffic.how could I force my ASA to set a different gateway for http/https/ftp traffic ?i have tried several solutions such as nat/pat rules, nothing seems to work.
View 7 Replies
View Related
Feb 13, 2011
I am using ASA5510 and i want to know if it is possible to redirect http traffic to an internal proxy software. I explain : PC from the LAN use a internal proxy in their IE browser but some other PC doesn't use it.They are directy connected to the Internet using the Public IP from the WAN interface ( via NAT). Can we redirected this HTTP Traffic from the WAN interface to the Proxy in the LAN ?
Http Traffic will be routed like that : PC -> WAN interface -> Proxy -> WAN interface -> Internet In fact,can we create a rule saying : All http traffic which doesn"t come from the IP Proxy must be redirected toward proxy.
View 6 Replies
View Related
Aug 5, 2008
I have an ASA 5505 that I am using to connect my contractors to via an inside interface, the outside interface is my private LAN. I have setup on our corporate Proxy server to allow traffic from my outside interface of my ASA to go to the internet without credentials BUT log internet activity. The question is I want to know if the ASA can send that http & https traffic to my proxy server and all other traffic to my default route? I want to be able to send all internet traffic to my proxy server. This will avoid me asking the contractors to place proxy credentials in their browsers.
View 6 Replies
View Related
Sep 20, 2011
i have ACE 4710 appliance that terminate SSL and the connection to the servers is http.
The ACE (one Armed) is load balancing between two web servers and i am using stickness in order to take the connection on the same server based on cookie.I can access the website either by http or https., where on the web page there is a login credential to access using username and password.
When i access the website using https everything works fine and i can login to my account in https mode.When i access the website through http and login to my account the URL is redirected to https...normal because i am using action-list to rewrite the http into https. But when i exit the browser and access the website again using http it is not redirected to https(although i see that i am still login into my account i can see all the inforamtion in my account).
The customer wants the connection to be https even when i exit the browser and access the website again (within short time before the cookie exipres)
View 3 Replies
View Related
Mar 12, 2013
I've got a HTTP Redirect to a dedicated html site with our internet usage policy set up on multiple WAP4410N access points.This is working like a charm with laptops, but not with internet radios. They can't connect to the internet probably freezing on the http redirected site.Is there any way to exclude these devices from the redirect?
View 3 Replies
View Related
Sep 16, 2012
I have tried search but found found anything for the 3750 switch about how to redirect HTTP, HTTPS & SMTP traffic to altenative gateway, than our standard gateway on our network, so here goes:
The network that need the HTTP, HTTPS and SMTP traffic redirect is 192.168.5.0/24 and should be redirect to 192.168.5.205 where as all other traffic need to be direct to 192.168.5.199.
Can the 3750 switch do this typo of refirect and if how?? I cannot find anything on the Cisco site stating how or even if it is possible!
View 2 Replies
View Related
Apr 23, 2012
I have a 2504 and my goal is to automatically redirect a users home page when they connect to a certain internal website. Authentication isn't a real concern just now.
Is it possible to simply have a users home page redirected when they open their browser upon connecting to the SSID? All of the documents available have stated to use 802.1x / RADIUS or other fancy tools.
View 3 Replies
View Related
Jun 3, 2013
I am unable to redirect the HTTPS traffic on my cisco router with WCCP V2
View 2 Replies
View Related
Aug 27, 2012
I have reset my wireless connection numerous times, rebooted, tried wireless and wired and continue to have the same result - great signal; cannot connect to any webpage. Ran network diagnostics and everything seems to check out except the "DNS Server."
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:Documents and SettingsMarcy Musselman>ipconfig /all
Windows IP Configuration Host Name . . . . . . . . . . . . : MARCYS Primary Dns
[Code].....
View 8 Replies
View Related
Mar 26, 2012
On a Catalyst 6509 switch I have configured wccp protocol in order to redirect the Http traffic to a Bluecoat SG8100. It was working fine until a new L3 interface implementation.Thereafter I was unable to redirect the http traffic due to an error reported from the Cat6509: [code] After some checks I supposed that the problem should be the UDP 2048 port connection between the Switch and the Bluecoat while the switch L3 port and the bluecoat are on the same Lan. A deep analysis found that the WCCP protocol seems to be as follow:
-Proxy address 10.64.28.240 to Switch Port 10.64.28.250 Here I Am
-Switch Port 10.64.28.250 to Proxy address 10.64.28.240 I See You
-Switch Port 10.66.0.251 to Proxy address 10.64.28.240 UDP 2048 packet (dropped by firewall)
It's strange to me that the first dialog is correctly handled by the correct Cat6509 interface while the UDP packets are flowing from another Vlan interface not configured with the WCCP and apparently not involved on the protocol.Last of all the WCCP is now disabled and unusable?
View 4 Replies
View Related
Feb 23, 2011
how do I block / unblock ports in ASA Firewall 5500 series?
View 2 Replies
View Related
Mar 26, 2011
I have follow below URL to disable the https over web authentication:
[URL]
What i want to achieve is disable https over web authentication due to certificate issue, but it seems like even we have disable the http over web management as above URL describe, still https while doing web authentication. Or it is possible to configure use port other than 80, like 8080 for web authentication? (need to reboot the wlc?)Is there any bug that related to this CSCsy32145?
WLC Software Version 6.0.196.0
View 8 Replies
View Related
Nov 27, 2012
I am setting up an ASA 5550 8.4 and asdm 6.4. Last thing I am missing is to get the static nat rule done for https. Done it with asdm and cli and always end up with "error: nat unable to reserve the port". Looked around the Net so far and changed the http enable port to 4433. ASDM access is only configured for inside and mgmt port. Disabled under RA VPN all checkboxes in clientless ssl and any connection profiles since IKEv1 is used for vpn access.
View 2 Replies
View Related
May 1, 2012
I am familiar with how a proxy works. The client sends a request to the proxy server and the proxy server makes the connection on behalf of the client to the web page.My question is how does this work with HTTP and end to end encryption?I know that at a company the IT staff can install certs on the computers that link to the proxy thus breaking the end to end encryption and allowing the company to see what data is being sent.I however cannot find out or think of how else to proxy an HTTPS connection other than installing certs on the clients that allows the proxy to see the data.If the proxy makes the https request on behalf of the client via one session, the https session would terminate on the proxy and the proxy would have to create a subsequent https connection to the client.This would break the end to end encryption and the client should pick up on this unless the certs on the client have been changed.
View 1 Replies
View Related
May 5, 2011
I will be adding wireless access points or repeaters on a business network. The business already has one wireless router using a https login, that 15 computers are wired to, through switches. This Secure http router is directly connected to the cable modem.Would I be loosing the benefit of Secure http by adding wireless access points or repeaters that don't support it? Or would they be securely routed by the main https router connected to the gateway?I have never had the opportunity to work with a secure http router before.
View 4 Replies
View Related
Mar 15, 2012
I installed the LMS as ova template on ESXi and be able to connect via SSH, but when I try to connect via http or https I got the following error.
ForbiddenYou don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
View 11 Replies
View Related
Apr 20, 2011
Never seen a Cisco, or any other L3 switch before. Nor an Lx router. Any step by step,or class room or web based training, or a partner or Cisco helper to get us up to speed on this.Goal is to limit http and https traffic in favor of telnet to an AIX server and RDP to a Windows TS. Printing would be ahead of http/s and below the others.
Interstingly, the web site promises 9 videos, but there are only 8. The demo guide says about OoS: "Coming Soon".Where to go? Who(m) to call?
View 6 Replies
View Related
Nov 7, 2011
Any issues with IOS 12.4(16) through 12.4(25f) with HTTP/HTTPS protocols running on a 3825 router? I have a remote site that accesses a corporate application over an MPLS, sometimes it works fine, other times it will hang for hours. No errors on circuits, interfaces, ethernet interfaces, etc. Response times are averaging 50ms even when the application freezes. The only thing I can think of is that it could be an issue with the IOS version.
View 13 Replies
View Related
May 23, 2011
I'm trying to develop and test a website from my iPad. I have my laptop and iPad on same local network, 192.168.1.xThey can see each other over network and I can access the page:192.168.1.105:80 (my laptops local web server) from both iPad and laptop. However the application server runs on port 8080 and I cannot access this from either device/machine. the router's firewall is playing a role, and I have no software firewall running on laptop that I'm aware of (turned off windows 7 firewall).localhost:8080/myWebSite or 127.0.0.1 also works on port 8080.The only combo that does not work is 192.168.1.105 with port 8080. I need this so the iPad can hit the site so I can test locally while developing.
View 4 Replies
View Related
Dec 9, 2010
I was unable to access my ASA 5520 using HTTP/HTTPS even on the management interface. I had upgrade the ASA IOS to asa832-k8.bin and ASDM to asdm-634-53.bin. But, the issue still the same.
My browser show the error message as attach image.
PGA-Firewall-02# sh run: Saved:ASA Version 8.3(2)!hostname PGA-Firewall-02enable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface GigabitEthernet0/0 nameif public security-level 0 ip
[Code]....
View 7 Replies
View Related
Dec 11, 2012
I have a WRVS4400N I am able to block http sites such [URL] but everybody have access to [URL]
View 2 Replies
View Related
Feb 17, 2012
I have a WLC526 running sw version 4.2.61.8 that I finally got around to installing in my shop for testing after sitting on the shelf for several years. Since it's now out of warranty and I'm no longer certified getting the latest sw version isn't possible so I'm stuck with the version it shipped with.
1, How do we change the web log in page from https to http? No guest wants to get confronted with a certificate error page so https doesn't make sense.
2, The virtual interface used for Web-Auth provides for a DNS Name but if I set a name it won't resolve and the log in fails. If I delete the name it uses the assigned IP instead and works fine. How do I get the DNS Name to work since it looks more professional?
3, When changes are made to the WLC I was initially just applying the change and then saving the config but it appears for some of these changes to take affect I have to reboot. It this correct or am I just missing something.
Again some of these issues are probably addressed in the subsequent sw releases but since my device sat in a box for 3+ years I missed out on the opportunity to upgrade and now TAC is telling me { (no contract || no warranty == no software) }, despite the fact that this device reached its EOL.
View 5 Replies
View Related
Sep 5, 2012
wondering if redirection or conversion port 8080 into port 80 is possible? if so how and what cisco equipment can do that?
View 11 Replies
View Related
Jun 26, 2011
I am configuring a GSS to check an Web server that responds to https requests.I put 443 as the port but I don´t see replies from the server and the Answer Status is always offline.Other servers using http on port 80 are showing OK.The appliance is a GSS-4492-k9 Version 3.1(0).
View 2 Replies
View Related
Jan 31, 2007
I have a custom webauth page installed that I am using with web passthrough authentication on my WLC2006 in order to put up a acceptable use policy page. The WLC uses HTTPS to display this which causes a security certificate warning to appear if I go with the WLC's own self-signed certificate. Is there a way I can get the WLC to use plain HTTP to display this page instead so I can eliminate the warning? I have already tried installing a trusted 3rd party certificate on the WLC, but I have this very strange problem where mucking with the WLC's web authentication certificate in any manner causes all network activity on the WLC to break except for CDP and ARP, essentially leaving the WLC dead. Three weeks of troubleshooting with Cisco TAC has yielded no progress on that front so now I am trying to bypass the need for a security certificate altogether since I really don't need to encrypt my acceptable use policy page.
View 13 Replies
View Related
