Cisco Wireless :: WAP4410N HTTP Redirect And Internet Radios

Mar 12, 2013

I've got a HTTP Redirect to a dedicated html site with our internet usage policy set up on multiple WAP4410N access points.This is working like a charm with laptops, but not with internet radios. They can't connect to the internet probably freezing on the http redirected site.Is there any way to exclude these devices from the redirect?

View 3 Replies


ADVERTISEMENT

Cisco Wireless :: HTTP Redirect - 2504 WLAN Controller

Apr 23, 2012

I have a 2504 and my goal is to automatically redirect a users home page when they connect to a certain internal website. Authentication isn't a real concern just now.

Is it possible to simply have a users home page redirected when they open their browser upon connecting to the SSID? All of the documents available have stated to use 802.1x / RADIUS or other fancy tools.

View 3 Replies View Related

Cisco Firewall :: Redirect HTTP / Ftp Traffic (ASA 5510)

Apr 25, 2011

i have the following scenario :
  
ISP1-------ASA 5510----------ISP2
                    |
                    |
                    |
                  LAN
 
i would like to use ISP2 for all http/https/ftp traffic.how could I force my ASA to set a different gateway for http/https/ftp traffic ?i have tried several solutions such as nat/pat rules, nothing seems to work.

View 7 Replies View Related

Cisco Application :: CSS Or ACE 4710 Redirect HTTPS To Http

Feb 27, 2012

For a CSS with a SSL module (performing SSL termination) - is it possible to impliment a redirect on https URL to send to equivalent http URL.If my understanding is correct, the CSS will do SSL termination and then use an http content rule on the resultant http stream as it is recursively handled by the CSS ? This would mean that the SSL module has no way of seeing/acting on layer 5 and above data (i.e. picking up on a specific URL) and can not itself issue a redirect - i.e. you could not associate a redirect statement or service with the following ssl content rule ? [code]The CSS would instead rely on a http content rule to impliment a redirect - i.e. you would have to associate a redirect statement or service to the following http content rule instead?
 
But if the CSS is already handling traffic for existing url...  traffic that is going to cause a loop when a client goes direct to. url...I realise the requirment is uncommon / a bit convoluted, its one of those don't ask type scenarios - aimed at achieving a specific requirement.Would the ACE 4710 be able to handle such a scenario any differently ?

View 7 Replies View Related

Cisco Application :: ACE 4710 - Redirect HTTP To HTTPS?

Jun 21, 2012

I am trying to make a redirect from http to https. the goal is whenever a user writes in http://10.80.199.71 it should be redirected to https://10.80.199.71 I am just haveing some trouble making it work.

View 4 Replies View Related

Cisco Application :: ACE 4700 Redirect HTTP To HTTPS?

Feb 6, 2013

How to configure a redirection on the ACE from HTTP to HTTPS using specific URL example [URL] to [URL], the SSL certificates were installed on the servers.

View 7 Replies View Related

Cisco Firewall :: Redirect Http / Https To Port 8080 PIX 6.3?

Feb 27, 2013

I need to redirect all http and https traffic from one source in a dmz network, to port tcp/8080 on a proxy server on the inside network.
 
The source device doesn't handle proxying very well, so i've been advised to redirect the tcp/80 and tcp/443 ports to tcp/8080 as it passes through the firewall.
 
Scenario is thus:
PIX 515E 6.3 (5)
DMZ server: 172.31.255.250 (Real IP), 10.44.181.236 (NAT IP)
Inside Proxy server: 10.44.132.28 (Real IP), 172.31.255.110 (NAT IP)
 
I've configured a static NAT redirect using the following command: static (inside,dmz) tcp 172.31.255.110 www 10.44.132.28 8080 netmask 255.255.255.255 0 0
 
When I try to add the next command of: static (inside,dmz) tcp 172.31.255.110 443 10.44.132.28 8080 netmask 255.255.255.255 0 0
 
I get the following error: ERROR: duplicate of existing static
 
Is there a work around for this at all or am I stuck with the limitations of the software?

View 2 Replies View Related

Cisco Switching/Routing :: HTTP Redirect Using 3750 Switch

Sep 16, 2012

I have tried search but found found anything for the 3750 switch about how to redirect HTTP, HTTPS & SMTP traffic to altenative gateway, than our standard gateway on our network, so here goes:
 
The network that need the HTTP, HTTPS and SMTP traffic redirect is 192.168.5.0/24 and should be redirect to 192.168.5.205 where as all other traffic need to be direct to 192.168.5.199.
 
Can the 3750 switch do this typo of refirect and if how?? I cannot find anything on the Cisco site stating how or even if it is possible! 

View 2 Replies View Related

Cisco Switching/Routing :: 6509 Unable To Redirect Http Traffic

Mar 26, 2012

On a Catalyst 6509 switch I have configured wccp protocol in order to redirect the Http traffic to a Bluecoat SG8100. It was working fine until a new L3 interface implementation.Thereafter I was unable to redirect the http traffic due to an error reported from the Cat6509: [code] After some checks I supposed that the problem should be the UDP 2048 port connection between the Switch and the Bluecoat while the switch L3 port and the bluecoat are on the same Lan. A deep analysis found that the WCCP protocol seems to be as follow:

-Proxy address 10.64.28.240 to Switch Port 10.64.28.250 Here I Am
-Switch Port 10.64.28.250 to Proxy address 10.64.28.240 I See You
-Switch Port 10.66.0.251 to Proxy address 10.64.28.240 UDP 2048 packet (dropped by firewall)
 
It's strange to me that the first dialog is correctly handled by the correct Cat6509 interface while the UDP packets are flowing from another Vlan interface not configured with the WCCP and apparently not involved on the protocol.Last of all the WCCP is now disabled and unusable?

View 4 Replies View Related

Cisco Firewall :: Redirect Http And Https Traffic From ASA 5520 Via Squid?

Dec 20, 2010

Right now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?

View 18 Replies View Related

Cisco Firewall :: ASA5510 - Redirect HTTP Traffic To Internal Proxy?

Feb 13, 2011

I am using ASA5510 and i want to know if it is possible to redirect http traffic to an internal proxy software. I explain : PC from the LAN use a internal proxy in their IE browser but some other PC doesn't use it.They are directy connected to the Internet using the Public IP from the WAN interface ( via NAT). Can we redirected this HTTP Traffic from the WAN interface to the Proxy in the LAN ?
 
Http Traffic will be routed like that : PC ->  WAN interface -> Proxy -> WAN interface -> Internet In fact,can we create a rule saying : All http traffic which doesn"t come from the IP Proxy must be redirected toward proxy.

View 6 Replies View Related

Cisco Switching/Routing :: 6509 Use Policy Based Routing To Redirect Http Traffic

May 29, 2012

We have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?

View 11 Replies View Related

Cisco Wireless :: Using Both Radios On 1200 Series AP?

Jun 7, 2012

I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.

View 1 Replies View Related

Cisco Wireless :: 5508 Does WCS Automatically Reset Radios

Feb 8, 2012

I have a WCS, four 5508 controllers, Cisco 3750X switches, and both autonomous Cisco 1200, and LightWeight 3502i  in service.The problems I am having, is that some of my Access Point reset for no apparent reason, and I get alerted by my NMS.When I look at the switch port, that connects an access point that reported down, I see the POE switch port went down and back up in 4 seconds, just long enough for the access point to reset.There are no errors on the switch port(s).  No cable or speed/duplex issues. Switch IOS: c3750e-universalk9-mz.122-55.se1

There are no other pertinent entries in the switch log.  Just that the port went down and then back up. Always in 4 seconds.When a reset happens the WCS reports on the access point: '802.11/b/g/n' interface of AP associated to controller 172.20.0.x is down. Reason: Indicates that while the radio state should be updated on controller, no reset should be reported.But nothing else, except that the radio came back up.
 
This is happening two or three times a day, and rotates. It seems that it never happens at the same time of the day, or the same access point, or the same switch.  (I have over 1000 access points and 500 switches in service)I am curious if the WCS is automatically resetting the access point radios, which is causing the switch port to go down/up?And if so, is it possible to turn off the automatic reset?

View 2 Replies View Related

Cisco Wireless :: 1141N And 1142N Radios Constantly Going Down

Apr 30, 2012

My co-workers and I have been trying to diagnose a problem that recently started occuring on our AP1141N and AP1142N units.  I have found a handful of posts that talk about this issue, but none with a solid solution. It seems that as often as every 24 hours, the radio interfaces change state to down, for seemingly no reason. Once this occurs, the only way to bring the radio interface back up is to reboot the AP. As far as we know, this wasn't happening until recently, when we enabled the "N" speeds. Things were working correctly for a year or two while the APs were configured just for b/g operation. The following is the only seeminlg-relevant thing that shows up in the logs:
 
*Nov 12 00:53:02.508: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Nov 12 00:53:03.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
 
Some additional info:
 
- All of the APs are connected to PoE Cisco c2960 switches
- We have tried both hard-coded radio channels, and non hard-coded
- We have tried various ways setting power inline negotiation
- We are not using a WLC
- System Software Version:          12.4(21a)JA1
- Bootloader Version:          12.4(18a)JA3
 
I have attached output of sh run, sh log and sh controlers dot11Radio0. (Another oddiy - the line %DOT11-2-RESET_RADIO hasn't shown up in the other logs I have viewed after this issue occurs...)

View 8 Replies View Related

Cisco Wireless :: 802.11 WAP4410N To WAP4410N Backhaul Using N Protocol?

Apr 30, 2011

I have the following equipment:
 
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3

I currently have 1 AP connected to the router via copper.  The AP to AP link is over 802.11.  I have attached a diagram reflecting the current topology.
 
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable.  About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed.  The link is stable (I have had the best results with B/G).  The problem is, I didn't buy the 2nd 4410N to run the G protocol.  I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only.  I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.

View 1 Replies View Related

Cisco Wireless :: Some C1242 Radios Are Disabled After WLC 5508 Upgrade To 7.3.101.0?

May 2, 2013

One week ago I use a WLC 5508 to place and replace another WLC 5508 with version 6.0.199.4, when I conect the new WLC all AP´s works OK only 10 dont work and not are recognizes from the WLC with version 7.3.101.0. The fail is the radios stay disabled. All ap´s are AIR-AP1242G-AK9 . See the image below, the only difference this ten AP´s are conected in switches cisco all the rest are connected in switches of ohter vendor.   If possible some command in the configuration is not neccesary and make the bad function?This is tipically config apllied by the customer in they cisco switches interface   GigabitEthernet0/22description PB-RS-A22switchport access vlan 5switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type   inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable?

View 4 Replies View Related

Cisco Wireless :: Radios On 1242AG Stay Down With Injector And Cat6509

Apr 18, 2012

i noticed that the 1242AG does not bring up the Radios, when there is a Power Injector connected.I see in the Logs of the AP:
 
%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C6509 <Switchport MAC Add>

The Module in the 6500 is a   WS-X6348-RJ-45 The Option "Power Injector installed" on the WLC is also enabled, with the MAC Address from the Switchport, but no change.When i disable CDP on the mentioned Switch Port and reload the AP, it comes up and runs fine.

View 7 Replies View Related

Cisco Wireless :: 1262 / Crossing The Radios In Repeater Mode

May 16, 2013

I'm trying to configure Cisco 1262 AP's to allow me to use the 2.4 gHz radio for client access and the 5.x radio for the repeater connection back to a root AP connected to a LAN.
 
I have already configured the AP's to associate with each other via the 5.x radio, and have a client connected to the repeater AP via the 2.4 gHz radio.  From my laptop on the LAN, I can connect to the repeater AP, but I cannot ping nor otherwise communicate with the distant client.
 
When I use the 2.4 gHz radio for repeater mode, clients that connect to the repeater AP can be seen and communicated with.Is there something special that needs to be done to get my desired scenario to work?All radios are members of bridge group 1.

View 5 Replies View Related

Cisco Wireless :: 1262N AP Disables Radios When Switched To Workgroup Bridge Mode

Feb 21, 2013

I am trying to enable the workgroup bridge mode on the 5ghz 802.11N radio of a Aironet 1262N, but when I select the workgroup bridge mode from the GUI the radio becomes disabled.  If I select the Access Point role from the GUI then the radio instantly becomes enabled.  The same thing happens if I attempt the same procedure with the 2.4ghz radio as well.  I can get the radios from both bands enabled if I select the Access Point role.  I made sure to check that both radios were not set to workgroup bridge as well.  I am running 12.4(25d)JA1 code on the AP.  This is my first time working with this type of AP.

View 2 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect To Wifi Radios Wirelessly?

Sep 23, 2012

I just installed an E3200 to replace my old Linksys.  All my Nooks, IPADs, laptops and desktops are connecting wirelessly fine. However, I have 2 Wi Fi Radios that will pick up the network but will not connect and go into a network connect time out. One of the radios also has a hardwired connection and that is working fine.  I have checked and double checked the network name, WPA key, etc. Of course I have reset all the radios and reenter new data many times, both manually and auto.

View 3 Replies View Related

Cisco Wireless :: New WAP4410N Does Not Connect To Internet?

Aug 31, 2010

I just purchased a WAP4410N yesterday and connected it to the switch.  I can see the WAP4410N, can connect to it, but cannot connect to the internet.  I thought this was enabled out of box.  What do i need to do in order to activate internet connectivity?

View 1 Replies View Related

Cisco Firewall :: ASA 5505 - Http Inspection Dropping All Http Traffic

May 9, 2012

I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
 
Here is the setup: I'm not sure why the web traffic is getting dropped.
 
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto

[Code].....

View 2 Replies View Related

Cisco Wireless :: Setting To Configure Only To Surf Internet Through WAP4410N

Sep 22, 2011

I need to configure WAP4410N wireless access point for our company guest and visitors.i need them to only surf internet and not to go to LAN (servers).I think i need to create VLAN for this ? can any one tell me setting for configure only to surf internet thru WAP4410N ?

View 1 Replies View Related

Cisco Wireless :: WAP4410N That Only Allows Laptop Local Access - No Internet?

Jan 11, 2011

I have a WAP4410N that only allows my laptop local access, no Internet.  Here is the scoop:

- Other users connect to the WAP and get Internet access

- Laptop connects to many other networks and has Internet access

- Laptop is running Vista

- ipconfig /all has address, mask, gateway, DNS, and looks normal

- Adapter is Atheros AR5007 802.11b/g with latest drivers

View 2 Replies View Related

Cisco Wireless :: Can't Route To Internal Network Or Internet Through WAP4410n

Jul 31, 2011

I purchased a WAP4410n for our small office to provide wireless access to our internal network to laptop users. I have configured the device as simplistically as is possible, but although I can get my laptop to connect to the AP (verified by managing the device wirelessly as well as by pinging the IP address) I can not get to any other IP address on my internal network nor the internet.I gave the device a static IP address - 192.168.1.50 subnet 255.255.255.0 with a default gateway of 192.168.1.254 which is my 2811 router. I set up a WPA-secured SSID.
 
A second problem I have is that if I set up my laptop wireless card to get its' IP settings form a DHCP server, it picks up a 169.xx.xx.xx ip address - it is as if the AP is not passing my DHCP broadcast / response through.

View 6 Replies View Related

Cisco Wireless :: 4x WAP4410N Possible To Plug Internet Connection Into One Of Repeaters?

Aug 22, 2011

We have 4x WAP4410N access points 1 AP & 3 Repeaters, this works perfect. The situation at the moment is that the internet connection is plugged in with a cable on the AP but the question is that if it's possible to plug the internet connection into one of the repeaters?
 
After that are we still able to use the internet over al four access points?

View 1 Replies View Related

Cisco Routers :: How To Redirect Internet Traffic From RV082 To RV042 Through A VPN

Feb 24, 2013

We have offices in USA and Venezuela.In our USA office we have a RV042 router and in Venezuela we have a RV082 router.We have connected a VPN tunnel (gateway-to-gateway) between both offices.
 
The point is:How   could we redirect the internet traffic from our Venezuela office   (RV082) to the USA Office (RV042) to navigate using USA public IP's?
 
The   reason for this is that we need to use online streaming services which   are only available for IP's from USA and we can't use them from the   Venezuelan IP's.
 
We  can not use the PPTP option since the  equipment which will use the  streaming services (like hulu, crackle,  etc.) in Venezuela is a Google  TV device which doesn't allow the  configuration of proxy navegation or  PPTP VPN connections itself. That's  the reason why we need to do that  through the routers.

View 1 Replies View Related

Cisco Switching/Routing :: 3560 Redirect Internet Traffic

Nov 24, 2011

At one of my field offices I want to redirect internet traffic down a separate DSL connection instead of having it ride the T1 back to the main office then going out.  At this office I have a 2600 router, 3560 switch, with a Fortigate firewall in between DSL connection and LAN, Fa0/0 on router and firewall are both plugged in to switch.  I have seen posts that mention PBR or static routes which is the reccomended method for dealing with this? 

View 6 Replies View Related

Linksys Wired Router :: How To Redirect Internet Traffic From RV082 To RV042

Feb 24, 2013

In our USA office we have a RV042 router and in Venezuela we have a RV082 router. We have connected a VPN tunnel (gateway-to-gateway) between both offices.
 
The point is: How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
 
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
 
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.

View 1 Replies View Related

Cisco :: 2504 / Rename AP Name In Overview (at Monitor > APs > Radios)?

May 29, 2013

I've got a Cisco 2504 wireless controller, and I'd like to rename the AP name in the overview (at Monitor > AP's > Radios) so that I know which unit is placed where and hence be able to troubleshoot more easily.I haven't found any info about this, and usually that means it's not an option, right? I realise the AP name field comes from the device itself, but it seems impossible to rename the device too since I'm running on lightweight, correct?

View 9 Replies View Related

D-Link DIR-655 :: Cannot Connect Network Radios After Upgrading To Latest Firmware

Mar 21, 2011

Cannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios.  They connect ok using Belkin and Linksys routers.

View 4 Replies View Related

Slow Internet Access Keep Getting Waiting For HTTP

Aug 6, 2011

Situation: Slow internet access, after access keep getting waiting for HTTP, always see n items remaining.What can be done to speed up access?OS is windows 2003 R2, latest updates. [code]

View 15 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved