Slow Internet Access Keep Getting Waiting For HTTP
Aug 6, 2011
Situation: Slow internet access, after access keep getting waiting for HTTP, always see n items remaining.What can be done to speed up access?OS is windows 2003 R2, latest updates. [code]
View 15 Replies
ADVERTISEMENT
Oct 16, 2012
I have a PIX 515E V7.0.4 and I'm having trouble with http access between the inside interface and a DMZ zone I have. I have a web server setup in the DMZ with an web interface to upload/download files. I can connect to this interface from a workstation in the inside network but when I try to download a file it is incredibly slow. If I upload a file there are no speed issues. If I connect using an https connection then both upload and downloads are at speeds I would expect.
I have disabled http inspect but this didn't improve the speed connection.
Other http communications from inside to outside do not have any speed issues in either direction.
View 34 Replies
View Related
Nov 5, 2012
I am connected to the LAN via ethernet cable, but internet access is terribly slow - cant even browse internet properly (work network uses a proxy to connect to internet - not sure if that is relevant). I would like to remain connected to the LAN via ethernet (to provide easy connection to intranet and mail exchange server, but for outside internet connections, I would like to use a mobile 3g connection.
View 1 Replies
View Related
May 9, 2012
I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
[Code].....
View 2 Replies
View Related
Nov 4, 2011
We are having several issues with the new batch of RV016 (rebranded as cisco and with cisco firmware. The Cisco RV016’s are configured to load balance aDSL internet access from 4 Cisco 877 modems/routers. Ports used are WAN1, WAN2, WAN3, WAN4.
Issues are: WAN 1 port resets to 0.0.0.0 regularly and traffic on WAN 1 fails DNS fails regularly behind the RV016 onlyIntermittent internet connection behind the RV016Slow internet connection behind the RV016Extremely slow DNS query and reply behind the RV016 (DNS resolve takes 1min -1m30)
The issues above are reported from different deployment sites and with different scenarios.
We also test above with Code...
View 1 Replies
View Related
Aug 7, 2011
We have ASA 5540. We setup Site-to-Site VPN and Remote Access VPN (Cisco VPN client). If are running full tunnel on the Cisco VPN client, the internet access is slow. For example, when we are running full-tunnel, the internet speed is 16 Mbps based on Speedtest.net. When we go to Speedtest.net, some of the graphics do not load. If we are running Split-tunnel, the internet access speed is 78 Mbps based on Speedtest.net and the Speedtest.net web site loads all the graphics.
View 6 Replies
View Related
Oct 4, 2012
We have an ethernet port on Cisco router 1800 connected to the ADSL modem. The router does ip nat translation, but users complained it is slow when they access to internet. [code]
View 1 Replies
View Related
Mar 1, 2012
I cannot access http sites unless I manually write the prefix https. The issue is mainly on Wordpress blog pages and I have to keep writing https if I want to access other blogger's page.For the time being I am using Chrome's extension "Https Enforcer" which slows down my browsing speed but eventually the sites open. I have to disable it if I have to use google images. I use windows 7, Chrome browser, Pocket Modem.
View 2 Replies
View Related
Jun 26, 2011
I'm trying to connect to a wireless network provided by a Sprint mobile hotspot. My computer is running XP SP3 and using a wireless USB adapter to do it. (802.1n)I can detect the network but when I try to connect using Windows I get the message "Windows waiting for the network to be ready." And apparently the network is never ready.I can also use the software that come with the adapter. That doesn't work because when I put in the password for WPA 2, the program saves a password that is far longer then the one I entered. Then I get the message "Authentication failed!" Well, duh.Then the computer tries to connect over and over with no results. "Trying to connect ... disconnected ... etc."
View 13 Replies
View Related
Jun 13, 2011
About 1-5 times per week I will find the jrm process showing as "Administrator has shut down this server". I have written a script that 2/day checks the status of the jrm process and if it is down, restarts it (pdexec jrm). About 25% of the time the jrm process will then show a status of "waiting to initialize". The only way I have found to recover it to shut down CiscoWorks and restart it (takes about 25 minutes). Why it would shutdown or how to get it restarted after the initializing state?
View 7 Replies
View Related
Nov 10, 2011
I'm running Win7 and have recently had problems at startup. Initially I thought this was a Skype issue as removing it seemed to work, but alas the problem remains with it uninstalled. The PC boots ok and I can open programs quickly enough, but if they need internet access they hang for 5mins or so before the block clears and all is well. I have recently changed ISP provider to BT Broadband (UK) and have a new router which sets itself up and had been working fine.
View 9 Replies
View Related
Apr 25, 2012
i havent been able to print anything wirless or even with the usb cord in about a wk. i can try to print out anything it will say printing or nothing and nothing happens. just when i search to see whats going on, its says that certain amount of documents are waiting/pending. ive canceled them several times. i also know about the printer spooler i fixed that and i thought that was it, cuz i was able to print a color page for my kids right after, but after that i wasent unless i did the spooler thing again. and i try to print something from any sight and pop up thing comes out ive just moved it today to allow only for secure sights only. also i i went into printer setup and software did what it asked and nothing still. im on this page now told me to check ip address printed out for wirless network and it shows but and i viewed the summary for wired and there nothing shows. oh it wont print anything i need to print but it does print automatically epicurious receipe everyday. i have a windows 7 hp computer and and hp officejet pro 8600 all in one printer. i have set up to wireless.
View 1 Replies
View Related
Jun 20, 2011
At the beginning we had 2 issues:
1. net start crmdmgtd did start correctly, so we use resetcasuser.exe and it works some minutes then this issue came back again. I ask the customer to put the casuser in the local administrator group, then customer was able to execute net start crmdmgtd.
2. but some process doesn't start see pdshow.txt.When trying to launch ciscoview, we have this error :Error in communicating with DCRServer. DCR Server may be down. Please start the DCRServer and then refresh the page.At RME home page, I have a error message about jrm, but I don't remerber it.
In the pdshow, we can see that DCRServer is in Waiting to initialize state.We have installed the fix for CSCte49301 bug, but the issue still exist you will find dcrserver.log and dcrclient.log.
View 5 Replies
View Related
Aug 5, 2012
I have problem i want to access to my http server in my local network from outside
192.168.2.42 : it my server http
195.X.X.X its my internet IP but it was connected in eth 0/4
static (DMZ,Orange) 195.X.X.X 192.168.2.42 netmask 255.255.255.255
access-list outside-acl permit tcp any host 195.X.X.X eq 80
access-group outside-acl in int orange
but its not good why
View 15 Replies
View Related
Jun 20, 2011
I just upgraded my ASA 5585 cluster from 8.2 to 8.4. I also upgraded the asdm .bin from 6.35 to 6.43. after rebooter the cluster, I try to access it with ASDM installed on my computer but it blocked at 17%.I tried to access [URL] but I just an error (with IE & FF) [code] What did I miss in the ocnfiguration ? I precise that I never used the http page, I already had the ASDM installed from another ASA.
View 4 Replies
View Related
Jun 16, 2011
I try to access to WS-SVC-NAM-2 module in the Switch 6509. But is not work although the HTTP port is enabled (I tested with the command telnet @ip 80).
I try telnet access to the module to check the config , but I always the message that the lo gin / password is wrong even though they are valid.
View 4 Replies
View Related
Mar 15, 2012
I installed the LMS as ova template on ESXi and be able to connect via SSH, but when I try to connect via http or https I got the following error.
ForbiddenYou don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
View 11 Replies
View Related
Feb 23, 2011
configure my ASA 5505. It is setup using PPPoE. What I want to do is this:
I have one of my IP addresses (99.23.119.78) setup for ftp using the ftp protocol to our internal IP address 192.168.1.3. What I need is to also allow for HTTP access but not just that, I need it to forward the http port to port 9000 because the web interface requires port 9000 for customer access. Previously on our old firewall customers were able to access the web interface by browsing to [URL]. I would like to not have to not require the port in the URL.
In addition, I would like to be able to setup a different IP address in our range (99.23.119.73) to be setup for http access using the standard port 80 for the same internal IP address (192.168.1.3). This URL will allow us to access the administration web interface for the FTP server.
Here is my current config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU
[Code].....
View 4 Replies
View Related
Jan 29, 2012
I have a web cache server, and I redirect all the HTTP request to it using WCCP.
Everything works without a problem, however I have a monitoring system that every minute tests the access to some customer sites that are hosted inside our infra-strutcture.
As soon as I configured the WCCP the monitoring system complains of timeouts accessing those sites, about 20% of the requests start to fail (timeout).
I don't think it is the fault of the cache because in the WCCP ACL I exclude all traffic that comes from my monitoring system. However as soon as I turn of WCCP the monitoring system never ever gives timeouts accessing those sites.
Is there anything I should do in WCCP to tweak it? I have WCCP configured in my core gateway that is a CISCO 3750.
View 2 Replies
View Related
Mar 18, 2011
I recently got wireless internet in my apartment but am having trouble connecting to it. The other computers in the apartment are having no trouble. The network appears in the wireless networks list, but after I enter the network key it just loads with the "waiting for network" message until it times out. I can connect to other wireless networks. It takes a long time to connect to these other networks but eventually does, My computer is super old, but since I can connect to wireless I feel like the computer is not the issue.
View 2 Replies
View Related
Feb 22, 2013
I am trying to limit HTTP access to my server on the local network to a specific IP address. I create an Access Rule in the firewall section, however that doesn't work. The only way it works is if I add the internal IP address of the server to the Forwarding section where I create a new HTTP forwarding rule.However, that is not good because that allows ALL HTTP traffic to that server instead of just by the single IP address.
View 2 Replies
View Related
Jul 30, 2012
I am facing issue with http login after IOS upgrade on 3750 switches. I upgrade IOS from c3750-ipbase-mz.122-35.SE5.bin to c3750-ipbase-mz.122-53.SE2. bin Any other command I have to run.
View 1 Replies
View Related
Dec 9, 2010
I was unable to access my ASA 5520 using HTTP/HTTPS even on the management interface. I had upgrade the ASA IOS to asa832-k8.bin and ASDM to asdm-634-53.bin. But, the issue still the same.
My browser show the error message as attach image.
PGA-Firewall-02# sh run: Saved:ASA Version 8.3(2)!hostname PGA-Firewall-02enable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface GigabitEthernet0/0 nameif public security-level 0 ip
[Code]....
View 7 Replies
View Related
Aug 21, 2011
I have cisco 881 and configured with http access, but when i try to open in browser it's shows blank page. Is the Cisco 881 supports GUI ?
View 3 Replies
View Related
Apr 23, 2013
I was login with my "router password" to my EA4500 yesterday without problem, after I brought another EA4500 today and try to find out my existing EA4500 configuration.I just can't login..I mean it just stay forever on the "Waiting..." screen after I enter the "router password"
-no luck with changing browser, I try ie, firefox, chrome, is still the same
-no luck with other pc, I try login with another notebook or pc, is same..
-no luck with switch off, I try refresh button once, same..and try to turn it off 5 minute and try again..same
View 9 Replies
View Related
Dec 14, 2012
I am not able to access https sites (like banking etc.). Once I plug my old router back I have no such problem. I guess it must be router settings that I cannot figure out.
View 7 Replies
View Related
Feb 19, 2012
I configured 2960S switch as http server. I'm unable to access the switch GUI with non privilege 15 user, with privilege 15 user it's working.
View 7 Replies
View Related
Apr 8, 2012
I've just purchased a new X3000 and have spent the last 2 days trying to set it up. I can connect to the router and see the settings via the default 192.168.1.1. However when I try to get an internet connection, I keep getting this message :"Timed out waiting for authentication server to respond. Please verify that you have a network connection or contact your network administrator for assistance (412)"I'm using my company-supplied VPN software to connect to my company network, and this is mandatory for me. Not sure if the issue is with this connection software.I bought the X3000 to replace my WAG160N, which was a breeze to set up compared to the X3000.
View 2 Replies
View Related
Feb 16, 2013
Its been half an hour now, what do i do?? I dont wanna screw up the router.
View 3 Replies
View Related
Oct 21, 2012
After replacing a Cisco CSS/SSL Accelorator and PIX firewall with an ACE 4710 to do load balancing and SSL encryption behind an ASA firewall we started seeing mangled HTTP requests in the Apache access logs for the servers in the server farm. This is occurring for several different URLs and not just the one above and for multiple web browsers.The ACE load balances to servers running Tomcat 7 with Apache HTTP server v. 2.2.14. A recent ACE software upgrade to A5(2.1) has not fixed the problem.
View 1 Replies
View Related
Oct 26, 2012
I have configured a portchannel with 3 ports - lacp active mode I want to pxe boot esx server with Hp Proliant DL 360 G7.
During Pxe Boot the physical Interfaces must be in (I) state - standalone.
The server receives via dhcp the ip but after getting the ip the link goes down for a short time and the switchport goes down and then in (w) state - waiting to be aggregated. Now the server tries to load via tftp the image but the server gets a timeout because the switchport is in state (w). It takes a long time til the switchport comes back in standalone mode (I).
Is it possible to modify the time how long the switchport is in the waiting to be aggregated state on 3750x ?
Would the right command be lacp rate-fast? But this command is not available on 3750x, only 6000 series.
View 0 Replies
View Related
Mar 12, 2013
I've got a HTTP Redirect to a dedicated html site with our internet usage policy set up on multiple WAP4410N access points.This is working like a charm with laptops, but not with internet radios. They can't connect to the internet probably freezing on the http redirected site.Is there any way to exclude these devices from the redirect?
View 3 Replies
View Related
Aug 27, 2012
I've got 3 computers. All running Windows 7 Home Premium. My desktop has an entire drive shared. I initially was having problems accessing the drive from both my HTPC and my laptop. I flushed the dns and reset winsock. reset IPv4 TCP/IP,and reset IPv6 TCP/IP.This fixed the problem from the laptop to the desktop, but the HTPC is still having problems accessing the desktop. The desktop however has no problems accessing the HTPC.Also have disabled auto tuning and the rdc.Forgot to add: Laptop is wireless the other two are wired.
View 4 Replies
View Related