Cisco Switching/Routing :: 881 Configured With HTTP Access Supports GUI
Aug 21, 2011I have cisco 881 and configured with http access, but when i try to open in browser it's shows blank page. Is the Cisco 881 supports GUI ?
View 3 RepliesI have cisco 881 and configured with http access, but when i try to open in browser it's shows blank page. Is the Cisco 881 supports GUI ?
View 3 RepliesI am facing issue with http login after IOS upgrade on 3750 switches. I upgrade IOS from c3750-ipbase-mz.122-35.SE5.bin to c3750-ipbase-mz.122-53.SE2. bin Any other command I have to run.
View 1 Replies View RelatedI configured 2960S switch as http server. I'm unable to access the switch GUI with non privilege 15 user, with privilege 15 user it's working.
View 7 Replies View RelatedI am configuring a GSS to check an Web server that responds to https requests.I put 443 as the port but I don´t see replies from the server and the Answer Status is always offline.Other servers using http on port 80 are showing OK.The appliance is a GSS-4492-k9 Version 3.1(0).
View 2 Replies View RelatedI have a sup 32 (WS-SUP32-GE-3B) i dont find any msfc card ? is there any command to check if msfc is present or offline/online ? Also will i be able to upgrade IOS for this sup with out MSFC ?
View 2 Replies View RelatedWhich IOS version for me3600 supports 4-byte BGP?
View 1 Replies View RelatedDoes Cisco Nexus 7010 supports NAT64; the image that I am using is :-
Software
BIOS: version 3.22.0
kickstart: version 5.2(4)
system: version 5.2(4)
BIOS compile time: 02/20/10
kickstart image file is: bootflash:///n7000-s1-kickstart.5.2.4.bin
kickstart compile time: 12/25/2020 12:00:00 [03/08/2012 03:58:13]
system image file is: bootflash:///n7000-s1-dk9.5.2.4.bin
does cisco switch 3560 or 3750 supports MC-LAg ? if yes, then on what IOS? if no, then what are the devices which supports MC-lag?
View 1 Replies View RelatedTrying to configure 1811w for wi fi . Need to use authentication shared keys but current IOS seems does not support ir
Router(config)#int dot11Radio 0
Router(config-if)#ssid manvee1
Router(config-if-ssid)#a?
% Unrecognized command
Router(config-if-ssid)#
(C181X-ADVIPSERVICESK9-M), Version 12.4(24)T8.
Need to know which IOS will support wi fi and authentication command under dot11 radio 0?
My 2691 Router has already 2 serial cards WIC-1DSU-T1 installed, When i install the 3rd serial card and reboot the router, it detects the 3rd card installed but 3rd card has no light.
When i do sh ver it shows 3 cards installed.
When i install this 3rd serial card to other Router then light shows on card and it works fine
So i am thinking if 2691 Router only supports 2 serial cards?
I like to know what is throughput of the Cisco 2911, cisco 2921 & cisco 2951 routers. I can see ISRG2 can supports the throughput of 150Mbps.
View 1 Replies View RelatedDoes the Cisco WS-C3560X-24P-S switch supports ip flow export?
View 1 Replies View RelatedWhat is the maximum group of HSRP Group that supports the WS-C3750G-24T-S running the IOS c3750-advipservicesk9-mz.122-44.SE2.bin?I have this message:Mensaje ERROR: %Platform already has maximum FHRP groups configured
View 6 Replies View RelatedI would like to ask for a cisco wireless router that supports captive portal. I notice that WAP321 supports this but what other additional units should be added in order to accomplish this. Client wants the user to authenticate first and also to see who logs in.
View 0 Replies View RelatedNeed to confirm if WS-C3750-48TS-S supports Private vlans and IPV6?
Also need to know which stack cable like part number i can use for stacking them .
Any switch that supports 4096 multicast groups?I am working on a system that includes over a dozen catalyst 2960 switches. The customer has pointed out the 2960 switch does not satisfy the requirement to support 4096 multicast groups (even though it is more than adequate for the number of active multicast groups). It looks like the 3560 supports more multicast groups than the 2960, but is still far less than the requirement.
View 1 Replies View RelatedI have a few 3560E running Ver 12.2(50)se2. Can these boxes be configured to run VRF. I see a "sho IP VRF" option, but I do not see it available when under config t. Do I need to do a IOS upgrade to be able to configure VRF?
View 7 Replies View RelatedWe have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies View Relatedwe are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
We have a working PBR route map on a 6509 switch and a 3750 switch, each in different locations.On both devices, the route-map is configured to match on one of multiple ACLs, then set the next hop to a directly-connected IP address, like so: [code]
When copying in the ACL contents for "ACL20", they were accidentally copied in to the ACL1 list, and ACL20 was never created. Shortly after this was done, the next hop router went unreachable in both locations. Pings failed and the 6509 and 3750 each lost the EIGRP adjacency to the 1.1.1.5 router. After troubleshooting, I removed "match ip address ACL20" and connectivity returned.
My question is...if a PBR route-map tries to match on a non-existent ACL, what happens? Does it mark the next hop unreachable (even though it's directly connected) or does it match for ALL traffic and send *everything* there (thus, making it appear unreachable, as if a broadcast storm was happening)?
In the following scenario, how will the 2950/2960/2960S series behave:
- VTP server/domain configured on a 6509
- A access switch (2960) currently configured in transparent mode with all VLAN it requires
Will the switch drop any traffick if we change it from transparent to client mode if the VTP server has the exact same vlans defined as the access switch had when it was in transparent mode?
I have an 2960S all configured, with vlans, ports configurations and others.Now, I bought other 2960S and two stack modules to create a stack with these 2 switches.We call:
-Switch1 (I have configured and in production)
-Switch2 (New switch, no configured)
Can I connect these two switches in stack without lost the configuration of my Switch1 and no turn-off this switch? Does not stop the users access?
I've created the VLAN on the Database but it tells me that there are no VLANs configured when i issue the command. Both VLAN 110 and 111 status are down, down.. Below is my config:
Building configuration...
Current configuration : 15817 bytes!upgrade fpd autoversion 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice counters max age 10!hostname Router!!no aaa new-modelip subnet-zero!!!ipv6 mfib hardware-switching replication-mode ingressvtp domain Marinersvtp mode transparentmls ip multicast flow-stat-timer 9no mls flow ipno mls flow ipv6no mls acl tcam share-globalmls cef error action freezeno scripting tcl initno scripting tcl encdir!!! !!!!!!!redundancymode ssomain-cpu auto-sync running-configspanning-tree mode pvstno spanning-tree optimize bpdu transmissiondiagnostic cns publish cisco.cns.device.diag_resultsdiagnostic cns subscribe cisco.cns.device.diag_commands!vlan internal allocation policy ascendingvlan access-log ratelimit 2000!vlan 110name Data!vlan 111name Voice!vlan 112name Video!------------Output
[code]....
I'm working on my CCNA. I purchased an old router 2610 with two ethernet ports. I configured the IP addresses on the interfaces and added the default gateway. I configured NAT to go out my ATT DSL router to the internet. With the 2610, I'm able to ping the back end or internal DSL router, but I can't ping the front end, external router, or out to any internet site such as google.
View 10 Replies View RelatedI am trying to figure out what is heat dissipation of a C6509-E configured as follows:
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
1) The power calculator says 13630 BTU/h
2) Manual calculation says: [code]
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?
Trying to apply this config to a 2900 router and getting this error message. [code] This works ok in in a 2800 router using 12.4(25d) spservices IOS
Not working on 2911 using 15.2(3)T2 ipbase image.
We are trying to test multicast between VRFs configured on Nexus 7Ks. Two Nexus 7Ks are configured for VPC. Multicast Server is in one VRF where as Receiver is in another VRF. The two VRFs are connected to each other via Checkpoint Firewall (Active/Active cluster in unicast mode). All routes have been established and connectivity tested between multicast server and receiver using ICMP.Using, windows mcast.exe multicast stream is generated from server (in one VRF) intended to be received by receiver (in second VRF). Every time, only one multicast packet is received by the receiver and rest all packets are being dropped. Server and Receiver are VirtualMachines configured on VMWaresame chassis which is connected to two Nexus 5Ks (VPC configured).
View 1 Replies View RelatedI have a switch that I have configured for jumbo packets, but they don't seem to be functioning. I have set system mtu jumbo 9000. The hosts are connected via 2x EtherChannel links. The hosts are jumbo frame enabled, and can ping their own local address using jumbo packets & do-not-fragment flags on the pings. They cannot, however, ping each other or the switch that way - it always says that the packet requires fragmentation. I know the attached machines (they're all VMs) and virtual switches support jumbos because I can ping within the virtual interfaces of the VMs. It's just traffic that goes over the switch that fragments.The switch is a WS-2960G-48TC. Here are the various outputs, with a section of config at the end.
hrnacancwtdevs3#show system mtu
System MTU size is 1500 bytes
System Jumbo MTU size is 9000 bytes
System Alternate MTU size is 1500 bytes
Routing MTU size is 1500 bytes
[code]....
how my switches are configured, a cisco 3750 and a cisco 4506.[code] i can ping the gateway from the 3750 however cannot get anything past that or enything to it.
View 12 Replies View RelatedI have two Cisco 4506's running cat4500-ipbase-mz.122-50.SG3.bin. Periodically, when attaching a new workstation to these switches the Mac Address of the device disappears off the port when the device is connected or the port is configured. The only way to correct the issue is to do a hardware reset on the blade or reboot the switch. After resetting the blade or rebooting the switch the devices will start showing up on the port and connect. This does not effect devices that are already connected to the switch, just newly added devices
Both switches are populated with WS-X4148-RJ45, WS-X4148-RJ45V and WS-X4248-RJ45V blades. It doesn't matter which blade the new device is being connected to. I believe that this may be a "Bug" but have been unable to locate one.
I configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
I would like to know how many port channel can i configured in the switch 3750 X ? and if there is a limitation by IOS ?
View 4 Replies View RelatedI have configured Cisco 1841 router PAT buts its not worked, find the below configuration details,
In LAN interface
Interface gigabit Ethernet 0/0
no shutdown
[code]......
Similarly I have configured static and dynamic nat but its not works in my customer place.