I have a sup 32 (WS-SUP32-GE-3B) i dont find any msfc card ? is there any command to check if msfc is present or offline/online ? Also will i be able to upgrade IOS for this sup with out MSFC ?
View 2 RepliesI have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies View RelatedI used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
I have been tasked to replace a failed sup on a 6500 Sup32 running IOS. Now, the primary sup doesnt have a compact flash. I don't have any CF on me. The replacement sup i received also doesnt have a CF.From the cisco website it says that the moment I insert the secondary sup into the chassis. it will automatically download the IOS and boot details from the primary to the secondary sup.
[code]....
I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.
View 5 Replies View RelatedI need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
let me know if the upgrade would be safe or not as far as the bandwidth?
I have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
I understand that my questions seems to be rather strange cos supervisors is rather old (Sup1A especially). But i am interested in understanding what puprpose were in production SUP32. I cant find out enough differencies between Sup1A with MSFC2 and Sup32 to understand what reasons lead to deploying new sup in none fabric supervisor series.
Both supervisors have same perfomance - 15Mpps and have limitation on backplane bandwith of 32 Gbps (cos both use swithing bus), both supervisors equipped with MSFC2 and etc. Differencies i found:
SUP 32 have 10Gbe ports support (but this seems to be doubtful enhancement - with it perfomance GE ports seems to be more appropriate technology isnt it?) SUP1A equipped with PFC, SUP32 with PFC3BSUP32 deploys CEF (what is benefit of CEF if perfomance same?)
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
is there any specific way to create the SVI Interface on MSFC , actually I need to create the two SVI Int on MSFC to enable routing in between two VLANs on 7613 chassis.
View 2 Replies View RelatedWhich IOS version for me3600 supports 4-byte BGP?
View 1 Replies View RelatedDoes Cisco Nexus 7010 supports NAT64; the image that I am using is :-
Software
BIOS: version 3.22.0
kickstart: version 5.2(4)
system: version 5.2(4)
BIOS compile time: 02/20/10
kickstart image file is: bootflash:///n7000-s1-kickstart.5.2.4.bin
kickstart compile time: 12/25/2020 12:00:00 [03/08/2012 03:58:13]
system image file is: bootflash:///n7000-s1-dk9.5.2.4.bin
I have cisco 881 and configured with http access, but when i try to open in browser it's shows blank page. Is the Cisco 881 supports GUI ?
View 3 Replies View Relateddoes cisco switch 3560 or 3750 supports MC-LAg ? if yes, then on what IOS? if no, then what are the devices which supports MC-lag?
View 1 Replies View RelatedTrying to configure 1811w for wi fi . Need to use authentication shared keys but current IOS seems does not support ir
Router(config)#int dot11Radio 0
Router(config-if)#ssid manvee1
Router(config-if-ssid)#a?
% Unrecognized command
Router(config-if-ssid)#
(C181X-ADVIPSERVICESK9-M), Version 12.4(24)T8.
Need to know which IOS will support wi fi and authentication command under dot11 radio 0?
My 2691 Router has already 2 serial cards WIC-1DSU-T1 installed, When i install the 3rd serial card and reboot the router, it detects the 3rd card installed but 3rd card has no light.
When i do sh ver it shows 3 cards installed.
When i install this 3rd serial card to other Router then light shows on card and it works fine
So i am thinking if 2691 Router only supports 2 serial cards?
I like to know what is throughput of the Cisco 2911, cisco 2921 & cisco 2951 routers. I can see ISRG2 can supports the throughput of 150Mbps.
View 1 Replies View RelatedDoes the Cisco WS-C3560X-24P-S switch supports ip flow export?
View 1 Replies View RelatedWhat is the maximum group of HSRP Group that supports the WS-C3750G-24T-S running the IOS c3750-advipservicesk9-mz.122-44.SE2.bin?I have this message:Mensaje ERROR: %Platform already has maximum FHRP groups configured
View 6 Replies View RelatedI would like to ask for a cisco wireless router that supports captive portal. I notice that WAP321 supports this but what other additional units should be added in order to accomplish this. Client wants the user to authenticate first and also to see who logs in.
View 0 Replies View RelatedNeed to confirm if WS-C3750-48TS-S supports Private vlans and IPV6?
Also need to know which stack cable like part number i can use for stacking them .
Any switch that supports 4096 multicast groups?I am working on a system that includes over a dozen catalyst 2960 switches. The customer has pointed out the 2960 switch does not satisfy the requirement to support 4096 multicast groups (even though it is more than adequate for the number of active multicast groups). It looks like the 3560 supports more multicast groups than the 2960, but is still far less than the requirement.
View 1 Replies View Relatedwe are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
I am planning to deploye the fwsm with all this complexity, will this type of senario work or not means traffic will move from msfc to the core.. Is this right to create another svi int2 on msfc to move traffic from msfc to core-switch.
G0/1(cisco7613) Vlan10----Vlan10(inside)FWSM-(outside)vlan20---Vlan20(inside)(svi-int1)MSFC(outside)(svi-int2)Vlan30---Vlan 30G0/2(Core-Switch)-----internet--->
If we have catos 6509 and MSFC and we need to connect new building with L3 I want to Do static route between two network i need to but ip in interface of switch should I but this ip on catos or MSFC,
Switch(config)# interface fastethernet 2/1
Switch(config-if)# ip address x.x.x.x x.x.x.x
In catos if want want do like above command what is the command .
I need to create a policy to provide only 4 Mbps bandwidth for mail out of 16 mbps pipe terminated on 7606 router (at Datacenter) having WS-SUP32-GE-3B.But I can't create policy with bandwidth percent,even exact value with priority command does not work. When I am going to enter service policy output command at interface it is showing as"priority command is not supported in output direction for this interface Configuration failed!" All I want to restrict bandwidth at backbone link for mail traffic. From all remote locations use to access mail server over the same link.
View 1 Replies View RelatedI have to do a migration of sup32 to RSP720 for which I need to know if you can operate the equipment connected with the 2 supervisors at the same time??? and it still working ?
View 1 Replies View RelatedI have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking abouth the procedure?shall i switch off the router ? or just removeSUP32 and insert RSP720 ?are there any steps should i do before the upgrade ?i am planning to take the router out of service during the operation, how much down time it will be ?
View 9 Replies View RelatedSince a couple of months, I have some CPU problem.
There is no high process :
l#sh processes cpu | exclude 0.00CPU utilization for five seconds: 39%/30%; one minute: 32%; five minutes: 32% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 130 52713208 240359987 219 0.95% 0.91% 1.00% 0 IP Input 202 1811824 1218190 1487 0.07% 0.06% 0.05% 0 HIDDEN VLAN Proc 338 20873364 219225 95214 7.11% 0.94% 0.71% 0 BGP Scanner
total amount of traffic on the router around 700Mb-1Gb out / 300Mb In
cisco CISCO7603 (R7000) processor (revision 1.1) with 458752K/65536K bytes of memory.Processor board ID FOX090308DTR7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 CacheLast reset from power-on5 Virtual Ethernet interfaces9 Gigabit Ethernet interfaces1915K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K)
I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
Is Ciscoworks LMS 3.2 supports WISM 2?
View 3 Replies View RelatedWhich version of IOS for the 2621 supports NAT?
View 1 Replies View Relatedthe max amount of AP's one 5508 WLC can support ?
View 4 Replies View Related