Cisco Switching/Routing :: Upgrade SUP2 To SUP32 On 6509?
Sep 18, 2012I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 6509 / Sup2 To Sup32 Upgrade?
Oct 7, 2012I need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
let me know if the upgrade would be safe or not as far as the bandwidth?
Cisco Switching/Routing :: Sup32 Upgrade On 6509 - Priority Command Not Supported In Output Direction For This Interface
Nov 15, 2012I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
Cisco Switching/Routing :: 6509 Amber System Light On Both SUP32
Feb 20, 2012I have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco Switching/Routing :: Getting 6509 VSS IOS Upgrade?
May 15, 2012Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6. Both 6509's have dual Supervisor cards installed. Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly. After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS??? See output below...
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS? I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues.
My Switch Id = 1 Peer Switch Id = 2 Last switchover reason = none Configured Redundancy Mode = sso Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :----------------------------------------------- Current Software state = ACTIVE Uptime in current state = 3 hours, 38 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:
[code].....
Cisco Switching/Routing :: 6509 VSS IOS Upgrade
Jan 15, 2012Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
I only have a single supervisor in each chassis.
Should I be ok with just following the eFSU upgrade instructions in the below?
[URL]
Cisco Switching/Routing :: Upgrade 6509-E Ios Image?
Jan 9, 2013I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies View RelatedCisco Switching/Routing :: 6509 SSO Redundancy IOS Upgrade
Sep 9, 2012I have a 6509 switch with SSO Redundancy (STANDBY HOT) with IOS ver 12.2(17d)SXB11, RELEASE SOFTWARE (fc1) (c6k222-jk9sv-mz.122-17d.SXB11.bin). I need to upgrade the IOS on this switch.I have 512MB Memory on the switch and 40144896 bytes free on Disk0.which IOS is the latest version to upgrade and also give me some hints for IOS upgrade on this switch?
View 7 Replies View RelatedCisco Switching/Routing :: 6509 Sup Engine 32 IOS Upgrade Via USB
May 14, 2013I would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before
View 5 Replies View RelatedCisco Switching/Routing :: IOS Upgrade For VSS 6509 Switches
Nov 19, 2012I have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
upgrade the IOS with VSS configured switches.
Cisco Switching/Routing :: 6509 Supervisor IOS Upgrade
Oct 16, 2012We are trying to upgrade the IOS on one of our 6509 switches. We have two 720 10GE supervisors running in SSO. Our procedure is reload the standby supervisor with the new IOS. We understand that you can only use one console connection when in RPR mode so we rely on the active supervisor giving us information that the standby unit is up and running.
The problem we have is that when we do a "show Module" on the switch the online diagnostics for the standby supervisor comes back us unknown. [code] We believe the active supervisor can see the standby supervisor because when we save the configuration we get a message saying that the config is sync'd with the standby router. We have a TAC case raised to investigate. We are upgrading from 12.2(33) SXI1 to 12.2(33) SXJ3
Cisco WAN :: 6509 What GBIC Is Installed On Sup2 Right Now Where Fiber Cable Is Connected
Feb 7, 2011We have a 6509 Sup2 at our ISP edge with fiber connection to ISP. I am planning on replacing the 6509 either with 7206VXR-GE2 or ASR 1002.
How do I find out what GBIC is installed on my Sup2 right now where Fiber cable is connected?What GBIC/SFP will be compatible for this on 7206VXR or ASR1002?If I use SFP do I need to change the cable connector?
Cisco Switching/Routing :: 6509-E VSS Will Upgrade Rewrite The Configuration
Jan 22, 2013I am planning on upgrading my 6509s to use VSS within the next few weeks. I have checked all of the hardware and software prerequisites, and we are good to go from that perspective.I do have more of a procedural question- my switches are already configured and in production, VLANs, HSRP (3 IP addresses per VLAN- 1 per switch plus virtual IP), etc. Does the VSS upgrade take all of this into account and rewrite the configuration correctly, or should I plan on redoing the entire config for the switches after the upgrade?
View 6 Replies View RelatedCisco Switching/Routing :: 6509 Supervisor Upgrade With FWSM?
Oct 8, 2012We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
1. Is above correct? Will my line card reload?
2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?
Cisco Switching/Routing :: Upgrade 6509-Chassis In VSS-Environment?
May 1, 2013we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")
2. inserting the line-cards exactly in the same slots and connecting all cables
3. switch on the new chassis, witing to come up in VSS
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
I've looked up cisco for some hints, but don't found anything.
Cisco Switching/Routing :: 6509 Upgrade To 12.2(33)SXI10 And ROMmon?
Dec 12, 2012I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to with the upgrade to 12.2(33)SXI10. Is this correct?
View 1 Replies View RelatedCisco Switching/Routing :: Load Led Indicator On WS-X6k-SUP2-2GE
Oct 29, 2011I have cisco catalyst 6509 with 2 x WS-X6k-SUP2-2GE. on the supervisor module is a switchload led indicator . I switch has never load according to load indicator.
Do i need to enable this in the switch config. The switch is running catos
Cisco Switching/Routing :: L2 Tunneling 4503 SUP2+TS?
Sep 16, 2012I need to implement over an ethernet link L2 tunnel because I want to isolate another VLANs domain.On the first side I can use the command : sw mo dot1q-tunnel on a new C4503 on the other side I cannot configure the command : sw mo dot1q-tunnel.
the other side is an old C4503 we upgrade the flash with a compact flash to upgrade to a new IOS v15 but the command doesn't exist also.I red the cisco feature navigator feature and I am sure the dot1Q-tunnel is available on my image : cat4500-ipbasek9-mz.150-2.SG.binso I don't know why I can use it.
Cisco Switching/Routing :: 6509 - Upgrade Sup720 To Sup2T In VSS Cluster
Jun 21, 2012I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
Cisco Switching/Routing :: 6500 - WS-X6K-SUP2-2GE - TCAM Exhaustion?
Nov 11, 2012we have a WS-X6K-SUP2-2GE running CATOS software, we are facing a TCAM exhaustion.I would like to know the following:
1. during an exhaustion, based on what ACLs will be kept in hardware or moved to software? the name or number gives any precedence to an ACL over another ACL?
2. If the TCAM's utilisation was on the limit and we increased ACEs to a specific ACL, all the ACL will be moved to software or only the new entries?
Cisco Switching/Routing :: QOS 6513 SUP2 Ayaya VOIP
Nov 15, 2011I am unable to find a sample config that doesnt use autoqos.
I need to enable QOS on a 6513 that I am using as a access switch.( loaded with WS-X6148-45AF). I am running SUP2MFSC2 with IOS and autoqos is not supported.
Below is my IOS version and my requirements.
Requirements:
Trust CoS and DiffServ Value coming from Avaya equipments
DiffServ=46 for Audio and DiffServ=26 for Signaling
CoS=5 for Audio and CoS=3 for Signaling
I am running the following IOS:
IOS (tm) s222_rp Software (s222_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF17b, RELEASE SOFTWARE (fc1)
Sample Port config:( Vlan 709 = Data,Vlan 809=VOIP)
Cisco Switching/Routing :: 6509 (HA) And FWSM (active / Standby) System Upgrade?
Sep 30, 2012I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies View RelatedCisco Switching/Routing :: 10G Line Cards Supported With 4503 SUP2+TS?
Nov 30, 2011I need a 10G support on 4503 chassi with SUP II plus TS.Is any of the 10G line cards i.e. 4712 or 4606 supported on SUP II plus TS on 4503?
View 4 Replies View RelatedCisco Switching/Routing :: 3750 / 6509 - Upgrade Core Switch Without Disrupting Network?
Feb 2, 2013I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies View RelatedCisco Switching/Routing :: Will WS-SUP32-GE-3B Supports IOS Without MSFC
Nov 13, 2012I have a sup 32 (WS-SUP32-GE-3B) i dont find any msfc card ? is there any command to check if msfc is present or offline/online ? Also will i be able to upgrade IOS for this sup with out MSFC ?
View 2 Replies View RelatedCisco Switching/Routing :: Replace A Failed SUP On 6500 Sup32
Oct 21, 2012I have been tasked to replace a failed sup on a 6500 Sup32 running IOS. Now, the primary sup doesnt have a compact flash. I don't have any CF on me. The replacement sup i received also doesnt have a CF.From the cisco website it says that the moment I insert the secondary sup into the chassis. it will automatically download the IOS and boot details from the primary to the secondary sup.
[code]....
Cisco Switching/Routing :: Catalyst 6500 Supervisors Differences Sup1A Vs Sup32
Feb 16, 2012I understand that my questions seems to be rather strange cos supervisors is rather old (Sup1A especially). But i am interested in understanding what puprpose were in production SUP32. I cant find out enough differencies between Sup1A with MSFC2 and Sup32 to understand what reasons lead to deploying new sup in none fabric supervisor series.
Both supervisors have same perfomance - 15Mpps and have limitation on backplane bandwith of 32 Gbps (cos both use swithing bus), both supervisors equipped with MSFC2 and etc. Differencies i found:
SUP 32 have 10Gbe ports support (but this seems to be doubtful enhancement - with it perfomance GE ports seems to be more appropriate technology isnt it?) SUP1A equipped with PFC, SUP32 with PFC3BSUP32 deploys CEF (what is benefit of CEF if perfomance same?)
Cisco Switching/Routing :: 6509 / 4900 - Network Down Cause Switching Supervisor With Redundancy
Jan 11, 2012we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedCisco Switching/Routing :: 6509 - Upgrading Switching Infrastructure
Apr 11, 2012The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
Cisco Switching/Routing :: Policy Routing Based On Client Gateway (6509-E)
Feb 26, 2012If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
Some info about hardware and config:
6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.
All routes are static, IP for 192.168.64.9 is on SVI vlan.
Cisco Switching/Routing :: 6509 MSFC - LAN Default Gateway Routing
Mar 6, 2012I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies View Related