Cisco Switching/Routing :: 6509 Amber System Light On Both SUP32
Feb 20, 2012
I have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
View 5 Replies
ADVERTISEMENT
Sep 18, 2012
I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.
View 5 Replies
View Related
Oct 7, 2012
I need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
let me know if the upgrade would be safe or not as far as the bandwidth?
View 2 Replies
View Related
Nov 15, 2012
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
View 3 Replies
View Related
Jul 15, 2012
What the little green/red light is on the back upper left corner of the switch is? It inside a little mesh and I belive it says vt_fail next to it.
Had water get on our switch over the weekend and this guy goes red when I fire off on demand diagnostic, but not relevant errors in any of the logs. Haven't gotten to the point where I am putting data back on the switch yet.
View 1 Replies
View Related
Mar 25, 2012
I am trying to configure BGP on 6509 IOS. I can not specify a long interger for autonomous system: ASN: 262829 (32 bits)
View 1 Replies
View Related
Sep 30, 2012
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies
View Related
Jan 31, 2011
I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.
View 1 Replies
View Related
Mar 24, 2013
I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies
View Related
Oct 30, 2011
We have one Cisco ACE in our data center which is working fine but has Amber light on front & Rear.
I read the document & it shows that either it is a system fault or internal fan failure.
I am sure it is a fan failure because if there was any system fault then ACE dont work properly. should we replace the hardware?
unfortunatley we dont have support contract & i am working to get it one.
View 1 Replies
View Related
Nov 24, 2012
I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
View 5 Replies
View Related
Apr 14, 2010
I have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies
View Related
May 4, 2013
I have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 Replies
View Related
Nov 25, 2012
We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies
View Related
Apr 25, 2013
What do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies
View Related
Oct 14, 2011
I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies
View Related
Oct 16, 2011
I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
View 3 Replies
View Related
Apr 17, 2013
Command to check system status of ACE 4710 appliace? For example if fan is OK or CPU temperature, or other HW things what could be faulty?
For example now I have system ID button blinking amber bot do not know what is wrong. I just know that there is some faulty.I just used show tech-support command and it does not seems that it include some HW statistics.
View 4 Replies
View Related
Nov 13, 2012
I have a sup 32 (WS-SUP32-GE-3B) i dont find any msfc card ? is there any command to check if msfc is present or offline/online ? Also will i be able to upgrade IOS for this sup with out MSFC ?
View 2 Replies
View Related
Oct 21, 2012
I have been tasked to replace a failed sup on a 6500 Sup32 running IOS. Now, the primary sup doesnt have a compact flash. I don't have any CF on me. The replacement sup i received also doesnt have a CF.From the cisco website it says that the moment I insert the secondary sup into the chassis. it will automatically download the IOS and boot details from the primary to the secondary sup.
[code]....
View 1 Replies
View Related
Feb 16, 2012
I understand that my questions seems to be rather strange cos supervisors is rather old (Sup1A especially). But i am interested in understanding what puprpose were in production SUP32. I cant find out enough differencies between Sup1A with MSFC2 and Sup32 to understand what reasons lead to deploying new sup in none fabric supervisor series.
Both supervisors have same perfomance - 15Mpps and have limitation on backplane bandwith of 32 Gbps (cos both use swithing bus), both supervisors equipped with MSFC2 and etc. Differencies i found:
SUP 32 have 10Gbe ports support (but this seems to be doubtful enhancement - with it perfomance GE ports seems to be more appropriate technology isnt it?) SUP1A equipped with PFC, SUP32 with PFC3BSUP32 deploys CEF (what is benefit of CEF if perfomance same?)
View 2 Replies
View Related
Mar 22, 2013
I have a PS3 connected to a Gig port on my 3560. When I boot-up the PS3 I have to wait around 30 seconds for it to get DHCP.
I noticed the orange LED would stay on and go green after 30 seconds. I assumed I would have an error-state but I do not, the port show connected with no errors even though it's orange. I have no connectivity from the ps3 until the light goes green and then all is well. The port is access and I have manually configured duplex and speed.
Switch>show version
Cisco IOS Software, C3560C Software (C3560c405ex-UNIVERSALK9-M), Version 12.2(55)EX3, RELEASE SOFTWARE (fc2)
[Code].....
View 5 Replies
View Related
May 8, 2012
I have a Cisco catalyst switch 3750G has all LED lights staying amber still without blinking, I cannot console into it and it can’t boot past the POST.
THE ISSUE HAPPENED ON THE NETWORK AND IT WAS ISOLATED FROM THE NETWORK, SO NOW I AM TRYING TO RESOLVE IT OUTSIDE THE NETWORK
View 3 Replies
View Related
May 10, 2013
In our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]
View 4 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Oct 27, 2012
I got 3 new TP-Link WA901ND PoE access points for a wireless network I manage. Right now I'm using the stock injectors that came with them because I need to get adapters still so I can use them with my PoE switch.
Hardware Version: v2
Firmware Build: 3.12.16 Build 120224 Rel.61005n
Wireless Mode: Access point
Channel: Auto
Mode: 11bgn mixed
Channel Width: 20/40MHz
Max TX: 300MBPs
About a week after getting these units installed and having them work great, I started running into problems. One of the unit's system light was not on, and I could not connect to the access point from my phone, or log into the web interface. I did a soft reboot (unplug for 30 seconds, plug back in) and it seemed to work fine, but then I had the same problem, and soon both units were doing it. I thought i might be pushing the distance limit the stock injectors have, but then I started having the same problem with a unit that is 10 feet from the injector.
View 11 Replies
View Related
Mar 14, 2013
I changed the setting from static to dynamic and the switch froze up. all lights on the panel flashed, when they stopped the system light on the left side continued to flash. I tryied unplugging unit as well as depressing the reset for longer than 30 seconds. Unit still the same.
View 8 Replies
View Related
Mar 23, 2013
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
View 2 Replies
View Related
Mar 25, 2013
Region : Others
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.11.3 Build 100408
ISP : Telekom
the SYS light, keeps blinking is that normal?
View 2 Replies
View Related
Feb 18, 2013
Region : Canada
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3.14.4
Recently in the morning the router will have lost ability to connect to internet <internet light is on> and I cannot access the router page <sys light solid> from either wired or wireless connections. Why is this and will it be solved if I upgrade firmware?
View 2 Replies
View Related
Sep 10, 2012
I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies
View Related
May 27, 2013
i recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
View 1 Replies
View Related
