I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
I was having problems connecting to one of my usb devices that was plugged into my router. I unplugged the router to reset it and whenever it starts up it flashes green and the green light goes solid for less then a minute before turning red. It's a solid red light. I've tried unplugging everything and restarting it and nothing. Ironically it still lets me connect to the internet but when I access the control panel on my computer it shows as disconnected. Is this means my router is busted. This is my second Belkin Router and the only reason I had to replace the last one is because it was a G+Mimi router and I upgraded to an N Router.
What do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
Everytime i plug the cable into my PC it doesn't detect it and the helper says to insert an ethernet cable.When I go to network sharing centre and check my connections it says network adaptor unplugged.im using wireless at the moment.My pc is a packard bell ipower x9810. it was windows vista but i upgraded to windows 7, i checked the packard bell website and can't find any networking adaptors. I have also checked device manager and it says - Belkin N+ wireless USB adapter #4 NVIDIA nForce 10/100/1000 Mbps Ethernet. there is no yellow exclamation mark.
I've noticed that the light on my laptop's Ethernet jack can be one of three colors depending on where it's connected.It's normally green, however in my dorm room it's red-orange, and at a local library it's amber.
i have beetel adsl2+router connected to my main computer through ethernet cable but its wifi signal is very low. its signal hardly reach the other end of my house where my bedroom is, and i want to surf on my laptop or mobile from my bedroom only so basically i want to extend my wifi range or boost the signal the thing is i have a belkin f7d1301 basic n150 wireless router, i want to know whether i can use it as range extender or any other thing to boost my signal.
I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
I recently purchased a Belkin F5D8053 N Wireless USB Adapter after my 6 year old adapter was unable to see my home network in the network list.
I installed the software but the adapter wouldn't connect to my home network so I reinstalled and updated the driver, still wouldn't work. Finally about 2 hours later it just randomly connected. Now it has been frequently (1-2 times a day) losing connection to my home network for around 3 hours, it can see a dozen networks in the list with full signal strength but won't connect to any at all then connects to my home network again several hours later.
I have switched between the Windows connector and the Belkin one and tried all 6 USB slots with no luck. I contacted Belkin support and they told me to try the device on another computer and see if the problem still happens but I don't have another computer to test it with.
I suspect this is a problem with my Windows installation rather than the hardware or router as my old card would freeze once every couple of days and was only fixed by powering off my computer as Windows was unable to kill the process to restart it.
I recently bought a router so I could connect my Toshiba laptop to the internet. After I connected the ethernet cable to the router and plugged everything in, I installed the program from the CD that it came with. After the whole process, it says "You are now connected to the internet!". Yeah well when I try to get on the internet, it suddenly takes the connection off. On my wifi status, it says it's not connected anymore. When I try to connect again, it says I'm connected, although if I get on internet explorer, it takes off the connection again. Though when it is connected, it says no internet connection available although I am connected to the router. So basically, I'm connected to the router, but not the router to the internet.
I am unable to connect to the internet through my wireless router. However, I can connect using neighbor's wireless connection and other laptops in my home are able to connect to the internet using MY wireless connection. The problem started suddenly, I used to be able to connect, then I had the problem so I rebooted and that resolved the issue temporarily. I tried disabling the wireless adapter card then rebooting, this did not work. I also unchecked the TCP/IPv6.
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
I have a printer (epson cx6600) I wanted to connect to our router here so everyone can print to it. It only has a usb connector (which you would typically connect to your pc)... I did notice they have usb to lan cables out there and was going to buy one and connect it to the router that way.
I'm trying to set up my desktop using windows xp and a wireless belkin n150 f9k1001 router to connect to a wireless network that is being sent from a mac with some tp-link router so that I can connect to the internet the isp is bell aliant. I'm not entirely sure how to go about this or if it's possible I've tried the worthless tech support and setting it up as an access point but I don't really know what im doing.
My WinXP Home PC won't connect properly (limited connectivity/no internet) via ethernet cable to my router (Belkin N150). Ipconfig /all shows the IP address as 169.254.117.71 but this is determined by an entry in the registry at HLMSYSTEMCurre....'DhcpIPAddress' - REG_SZ - 169.254.117.71. Also listed at 'IPAutoconfigurationAddress'. My laptop connects fine plugged into the same port getting it's IP automatically (192.168.2.2) and getting internet fine. I've tried adding a DWORD entry 'IPAutoconfigurationEnabled' = 0, also tried deleting the 2 values.Tried setting the IP manually to 192.168.2.6 - limited connectivity goes away but I get no internet connection from the router nor file sharing.
-no power light -solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.
F7D1301 v1 is my router model. i installed it this morning; all was working fine; then i changed password; still working fine; then i attempted to change pw a second time; router turned to solid orange and no matter what i try, i can't get it working again. i reset it, unplugged it, etc.
I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
We have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?
I have a fee pcs at home...all are able to connect to the internet but theres only one thats not able to...the network and connection centre keeps and changing from identifying to not connected. The cable itself is fine.
I can open files, play videos, run programs, etc. Windows installed without a problem.However, I can't connect to the Internet. At all. I can't even register my version of Windows because I can't contact Microsoft for verification, because the connection won't get through. No Internet devices can be detected.That was with a long cable wired directly to our router, which is next to our modem.So, today, I bought a D-Link Xtreme N Desktop PCI adapter to connect. Still no connection... I don't think the PC even detects the adapter, because the drivers coming with the adapter can't detect it, and the light on the adapter doesn't turn on.That shouldn't happen. Both the cable and adapter go directly into the motherboard. My operating system is Windows 7 Ultimate 64-Bit, and my motherboard is an Asus P8Z68-V PRO.My ISP is Cogeco. All other computers and wireless devices in the house work perfectly fine.
I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
I just got a new laptop. Like, just yesterday, but for some odd reason it can't connect to the internet in the living roomMore Info:Laptop bought yesterday. Absolutely new. Samsung, A6 Vision, Windows 7. It can hold to 480GB I think or at least around and has 6GB Ram. I brought it home, made the default brower Google Chrome and connected it to the home internet and entered in the security key/password, so it's all connected. IN the living room, the connection is really good. All the other laptops there -even my really bad old one can connect fine to the internet. My new one says it's connected, but no internet. But since the other ones get internet, I don't think I need to restart the router -although I did so anyways and it didn't work
After pconfig /renew (I get this error) No operation can be performed on pth while it has its media disconnected. An error occurred while renewing interface local area connect an operation was attempted on something that was not a socket.
I am also trying to wipe it but no not have XP disc and no one I know does either so what is the safest way?
We have 3 units of computer in our house uses a router and a 8port switch hub. The unit i am using can connect directly to the internet but cannot be mapped in lan. I tried pinging and i already assigned IP addresses in all units but still nothing happen. I already done format and cloned from the other unit.