I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
View 5 RepliesI reinstalled windows xp (reformatted c). Installed the drivers in this order: Controller, Video, Audio, Network, modem. I selected the drivers that had the check beside them on the driver disk. Now, in the device manager, there is a yellow question mark beside the ethernet card and I can't connect to my broadband connection. Wire is attached... checked that twice. I have connectivity through other computers, so internet is working in the house.
View 3 Replies View RelatedMy hard drive crashed. I have finished installing everything on a new drive that I have from my Dell installation CDs. However, in the Device manager, the Ethernet Contoller shows the the drivers are not installed. I can't seem to find them anywhere on the Dell web site.
when I pull the cover off of the computer - the outside of the Ethernet connection says "418D-J51 10/100 BT"
I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.
View 1 Replies View RelatedI have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies View RelatedWe have one Cisco ACE in our data center which is working fine but has Amber light on front & Rear.
I read the document & it shows that either it is a system fault or internal fan failure.
I am sure it is a fan failure because if there was any system fault then ACE dont work properly. should we replace the hardware?
unfortunatley we dont have support contract & i am working to get it one.
I have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 Replies View RelatedWe just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies View RelatedWhat do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies View RelatedI have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies View RelatedI have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies View RelatedI have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
View 3 Replies View RelatedI have a Dimension 4600i that doesn't want to Wake on LAN. I am running the latest BIOS (A10), Intel Chipset Drivers, and latest Intel Pro/100 VE Drivers. I set the Network Settings to Network w. PXE and the startup sequence is CD-ROM, PXE, Hard disk. I am actually using the PXE, that is exactly what I want. My only problem is I need to do Wake on Lan for the system to wake up and PXE against my backup server. So far, no luck. I have tried numerous utilities and when I send magic packet the thing just sits there, everything else works great, the darn thing just won't come alive unless I hit the power button.
View 2 Replies View RelatedMy ethernet was working fine when I shut down my computer then all of a sudden it rebooted and gave me a blue screen. I rebooted it and it started but then it was not able to connect to the internet. The pci adapter driver was not there. I reinstalled it and it still would not connect. I uninstalled it and reinstalled it, changed the ethernet cord for a new one and tested the new cord on a different device with no problem but stil cannot connect. It says network cable is unplugged. This happened before and the dsl technician was able to get it to work again unfortunately I have no idea how but it had something to do with the configuration.
View 1 Replies View RelatedAfter clean reinstall of windows XP Pro on Dell dimension 4600, computer not connecting to internet. I have it plug into port on my wireless router, I am posting this from different PC pluged into a port on the same router, so I do have internet to the PC.
View 13 Replies View RelatedI'm trying to fix my brother's computer (an old Dimension 4600). At first ISP modem wouldn't even detect his computer on the network. I downloaded the Ethernet drivers and installed them and now it detects his computer, but it still won't connect to the internet
View 4 Replies View RelatedI cant find a network driver that will work. I have a dell dimension 4600 that i am trying to run windows server 2008 on. its original opersting system was xp/sp3 . i simply want to know if there is any working Ethernet driver for windows server.
View 1 Replies View RelatedI tried to connect inet with a DSL "Speed Modem 200" (no WLAN!, no router), RAS failure 651.
OS WIN7 Enterprise, SP 1, 64-Bit
It seems to be a driver problem of the LAN adapter, because under XP SP3 on the old PC ervery thing is fine.The driver test told me "newest version" what's to do?
ive tried turning my modem/router off and on but to no avail, the lights keep blinking. so whats up with that?
View 2 Replies View RelatedThe green light on my Ethernet port is always on. Even when I unplug the Ethernet cable and shut down my computer. The only way it turns off is when I unplug my computer from the outlet. Also, my computer doesn't receive any internet when an Ethernet cable is plugged in and the yellow flashing light doesn't show either. I know the Ethernet cable is fine and the internet works fine on other computers
View 2 Replies View RelatedThe modem is sure working and so as the Ethernet cable since I am using it with another computer. I already had the driver updated but still it's not working. I actually suddenly heard noise in my computer before this happened. OS Windows 7.
View 7 Replies View RelatedHandPunch 3000 Time & Access Device, no Communication over the Ethernet, on the Ethernet Card the red light flashes for 1sec then red & Green for 1sec.
View 1 Replies View RelatedI had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
View 5 Replies View RelatedI find that one of the ethernet interface of ASA5510 always display RED light
View 3 Replies View RelatedI have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
View 1 Replies View RelatedWRT400N worked great for 18 months.
Last week the Verizon-supplied DSL modem went bad (wasn't receiving data) and was replaced.
Now I can get Internet direct out of modem, and when I connect it to router the router's Internet light is on, but it seems to stop there. Devices connected to router via Ethernet or wifi don't get Internet.
I'm able to get to the router's admin console via Ethernet and wifi, but no Internet.
I recently had a HD failure on my dell e1505. I replaced the HD and installed XP; everything seems fine except the modem doesn't work. It did before the HD crash. The diagnostic program does not indicate any modem at all, as if it were not installed. The Wi-fi light does not come on and it does not work with an ethernet cable plugged into the modem.
View 1 Replies View RelatedI switch to a new internet provider. which is wireless[Frontier]. my printer is dell V715w the orange light is flashing. provide detailed info to correct
View 1 Replies View RelatedI switched my Dell Latitude D630 on yesterday morning and the WiFi light wasn't lit, and I am unable to connect to any network. I'm completely baffled why this has happened. I was using it the previous night, streaming some music on Spotify, then I turned it off as normal, and when I tried using the internet the next day...nothing. The bluetooth light is lit as normal but the WiFi light stays off, and I've tried turning the external switch on/off to no avail.
View 8 Replies View RelatedI previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View Relatedis it possible to connect toshiba satellite pro 4600 into internet without the use of cable? how to convert it to wifi?
View 1 Replies View RelatedI am trying to light up every port light on a 3750g. There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?
View 3 Replies View Related