The green light on my Ethernet port is always on. Even when I unplug the Ethernet cable and shut down my computer. The only way it turns off is when I unplug my computer from the outlet. Also, my computer doesn't receive any internet when an Ethernet cable is plugged in and the yellow flashing light doesn't show either. I know the Ethernet cable is fine and the internet works fine on other computers
The modem is sure working and so as the Ethernet cable since I am using it with another computer. I already had the driver updated but still it's not working. I actually suddenly heard noise in my computer before this happened. OS Windows 7.
I had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
-no power light -solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
after several years of proper functioning my WAP started to make trouble and recently stopped working. I've tried a lot of options to get it back online but I failed doing so.The green ACT LED won't light up anymore so my laptop cannot find the WAP anymore. When connecting the WAP directly to the laptop the Network Center shows that Windows is trying to identify the WAP but this messages disappears and re-appears on and on but there is no succes in identification (ofcourse this is caused the the green ACT LED which won't light-up).
my family kept having a problem with our Billion 6800n router. (or something like that).Basically we pinned the problem down to it not having the strength to keep several connections running through it. So we upgraded to a Billion 7800n and found it is much more stable and much faster.However it has been having a similar problem to our previous router.
Occasionally the internet light drops from green to orange, and we can't load any more pages until it has gone back to green.Here is a picture of what it looks like when in that status.But the weird thing is the connection bars on the windows toolbar at the bottom of the screen still show full strength.As shown here.Now I thought it might be because it was sharing a power board with other connections going through it,so I transferred it to a smaller two-plug one instead.
For the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
Recently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
I am trying to light up every port light on a 3750g. There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?
I can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems attempted to fix problems via belkin software changed channels on modem updated firmware etc, etc
I recently upgraded my ADSL to a 1Mbps line and I got a new Fritz box(7390) with it and i bought a linksys ae3500 wireless router. I am using Bit comet to download my torrents and my listen port stays at a yellow light. I previously had only the Fritz box 7170 and my listen port was always green.
HandPunch 3000 Time & Access Device, no Communication over the Ethernet, on the Ethernet Card the red light flashes for 1sec then red & Green for 1sec.
I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
I have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
Last week the Verizon-supplied DSL modem went bad (wasn't receiving data) and was replaced.
Now I can get Internet direct out of modem, and when I connect it to router the router's Internet light is on, but it seems to stop there. Devices connected to router via Ethernet or wifi don't get Internet.
I'm able to get to the router's admin console via Ethernet and wifi, but no Internet.
I've had trouble connecting to my own internet and have no wireless. I'm using my neighbor's wireless and it's really slowing her's down. I've tried restarting my laptop (it usually works) and then reinstalled the device under "device manager". It's not the cord, I've checked with my neighbor's laptop and it works fine.I use a Sony Vaio VGN-NS140E with Windows Vista SP2.
------------------------------------------------------------------------ {ipconfig /all} This is while I only have an ethernet plugged in and no wifi connection. Windows IP Configuration Host Name . . . . . . . . . . . . : FairyHo
After a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
I plug the network cable and set an IP to GUI to the default IP (192.168.1.254)the problem is the port doesn't show light when connect to notebook. How am i supposed to enter GUI.
why the port is like in shutdown state and not enable? do i need to do anything via console??
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
There is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
if I can use the encrypted port as unencrypted ethernet ports? url.. Each individual port on the Cisco Nexus 5010 switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right.There are 20 to 28 ports on the Cisco Nexus 5010 switch, depending on which GEM is installed.
The 20 fixed ports form group 1 and are named 1/port_number. Ports 1 through 16 are unencrypted Ethernet ports. Of these, ports 1 through 8 are 10-Gigabit Ethernet and 1-Gigabit Ethernet-capable ports. Ports 17 through 20 are encryption-capable Ethernet ports.
I have just upgraded my Linksys router from an older one to the E-2500 about a week ago. Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers. I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan. Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.
I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.
I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.
I have a Cisco 857 router which i used for Internet connection with RJ11 connectior (ADSL0 POTS) but now the ISP has changed the internet link with PPOE type and the ONT connection is RJ45 , Is there a possibility to configure one os the Fast Ethernet ports as WAN port for internet.
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!