Linksys Wireless Router :: WRT300N Power Light Dim And All Other Ports Solid Green

Nov 20, 2011

I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.

ADVERTISEMENT

D-Link DIR-615 :: Power Light Is Off But WAN-L1-L2-L3-L4 Are Solid Green

Dec 23, 2012

I have a DIR-615 v e3 router

Did a bad dd-wrt flash and now all it does:

-no power light
-solid green lights: WAN-L1-L2-L3-L4

tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once

View 1 Replies View Related

Linksys Wireless Router :: WRT300n Version 1.1 - Power Light Blinking

Aug 15, 2011

If I conact from the modem to the pc I have internet so it must be the router.  The power light is blinking along with all the port lights.  Power light is blinking one time slow 2 fast.  Have tried holding the reset button for 30 seconds and unpluging for 30 seconds.   Can not go to the ip address it times out.  New firmware is not avalible.

View 9 Replies View Related

D-Link DCS-930L :: Firmware Upgrade Crash Solid Green Light

Oct 28, 2012

I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!!  I also can't find any posts relaled to my problem all over the internet.

View 3 Replies View Related

Cisco Wireless :: Can't Console Into 1252 AP And All 3 Lights Solid Green

Jan 18, 2011

Recently we had a situation where our users were unplugging one of our un-mounted 1252 LAPs. They would do this so they could borrow the wire to direct connect any one of their devices not realizing they were disconnecting a wireless access point. After discovering that the AP was unplugged once again, our admin plugged the AP back to the network but noticed that it no longer would connect to the controller. We can no longer console into the AP but can console into all other APs we have. All 3 lights are now green. Radio and Ethernet are solid and Status is blinking. I found the Cisco doc explaining the meaning of the front panel lights but have not found this particular configuration. What these lights mean and why not being able to use the console port?

View 11 Replies View Related

DCM425 Don't Turn Off Also Has 4 Solid Green Lights?

Mar 7, 2013

dcm425 dont turn off also has 4 solid green lights...it happen after a power outage my router works fine but my dmc425 cable modem just has the 4 green solid lights when it's plugged in when i push the power button nothing happens at all

View 3 Replies View Related

Linksys Wireless Router :: WRT54G V8 Power And LAN Light Won't Come On

Jan 24, 2009

Ive recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.

View 8 Replies View Related

Linksys Wireless Router :: Power Light On Wrt54g V2.2 Keeps Blinking

Oct 29, 2011

the power light on my  wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected

View 3 Replies View Related

Linksys Wireless Router :: X2000 Still Working But Only Red Power Light On

Jun 19, 2012

My Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).

View 3 Replies View Related

Linksys Wireless Router :: WRT54G Blinking Power Light

Jul 4, 2006

My Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?

View 9 Replies View Related

Linksys Wireless Router :: WRT160N Power Light Blinking?

May 11, 2009

So I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue.  Since doing that the power light has been blinking non stop.  I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on.  That little blue light just keeps flashing.  I can't even access the router setting page using 192.168.1.1.  My OS is  Windows xp x64 sp2, and I have DSL. 

View 9 Replies View Related

Linksys Wireless Router :: WRT54G 2.4 GHz Power Light Not Illuminated?

May 17, 2008

My router was working fine until today.    I figured it out when I tried to get on the internet and it wouldn't let me.  I hooked up the ethernet directly from my modem to my computer and then my internet worked fine. 

View 4 Replies View Related

Linksys Wireless Router :: WRT54G V5 Blinking Power Light

Oct 29, 2011

I need fixing my router. I updated the firmware and it said the upload has failed ever since then:

-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
 
My router is a WRT54G v5

View 9 Replies View Related

Linksys Access Point :: WAP54G Green ACT LED Does Not Light Up

Jun 22, 2011

after several years of proper functioning my WAP started to make trouble and recently stopped working. I've tried a lot of options to get it back online but I failed doing so.The green ACT LED won't light up anymore so my laptop cannot find the WAP anymore. When connecting the WAP directly to the laptop the Network Center shows that Windows is trying to identify the WAP but this messages disappears and re-appears on and on but there is no succes in identification (ofcourse this is caused the the green ACT LED which won't light-up).

View 1 Replies View Related

Linksys Wireless Router :: WRT54GS V1.0 Firmware - Blinking Power Light

Feb 20, 2012

No download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
 
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?

#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
 
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?

View 7 Replies View Related

Linksys Wireless Router :: WRT120n Not Working / Only Power Light Is Turning On

Sep 9, 2011

I have WRT 120 N which has apparently stopped working. When I turn it on, only the power led turns on without blinking, no other light flashes. My computer can't detect the router signals since the signal light is off. Neither does my modem show that the router is connected to it through the ethernet cable. My ethernet cable is working fine, since it is working directly with the computer.

View 6 Replies View Related

Linksys Wireless Router :: WRT54GS / Power Light Blinking - Internet Is Down

Feb 21, 2012

I have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard.  The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message:  "Firefox can't find the server".  I was no longer able to access the internet, and the router's green power light was left flashing.  It flashed for over 24 hours.  I tried unplugging the router and shutting down the computer,  then plugging in the router and turning on the computer.  (I don't have a modem.)  The light was still flashing.  I tried pressing the logo button for 5 seconds. Still flashing.  Tried pressing the reset button in the back.  Still flashing. 'I can't get on the internet or into the router.  Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.

View 8 Replies View Related

Linksys Wireless Router :: WRT54G V5 With Blinking Power Light Connected

Mar 24, 2011

I've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?

View 4 Replies View Related

Linksys Wireless Router :: WRT610N Power Light Flashing / Not Stable

Oct 2, 2011

i have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem

View 1 Replies View Related

Cabling / Cards :: Belkin Connect N150 Router Has Solid Amber Light?

Oct 16, 2011

I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.

View 3 Replies View Related

Linksys Wireless Router :: WRT54GC Ver2.0 LED Light Blinking Including Power

Apr 22, 2009

My wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.

View 9 Replies View Related

Linksys Wireless Router :: E1000 - Hardware Failure / Power Light On Continuously

Aug 7, 2011

I have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.

View 5 Replies View Related

Linksys Wireless Router :: E2500 Power Led Light On Back Started Blinking

Nov 8, 2012

I have a Linksys E2500 and recently the power led light on the back of the router started blinking.  The router itself seems to be working fine.  I can access the router and the router seems to be assigning the IP addresses fine.  I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking.  Not sure what to do anymore.

View 5 Replies View Related

Linksys Wireless Router :: WRT160Nv2 Power Light Not Stop Flashing With No Internet

Apr 25, 2009

So I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.

View 9 Replies View Related

Cisco Switching/Routing :: 2960 No Post / Solid Green Syst / Dead Switch?

Feb 16, 2013

I have 2 - WS-C2960-24TT-L switches. Both are experiencing the same issue. Upon booting them up, all lights flash on the mode indicator panel, then it goes directly to a solid green "SYST" light. Nothing registers across the console cable. I have tried different baud rates, cables and computers. None of the ports come up regardless of how long either switch is powered on. Holding the Mode button during boot up produces the same result, nothing. Sounds like they are dead, however, I thought this would be the place to go for ideas. Can I revive these switches?

View 3 Replies View Related

Cisco Wireless :: 1524SB - Have Root AP Whose Status Light Showing Solid Red

Jun 30, 2011

We have a root AP whose status light is showing solid red.  We power cycled it and it still shows solid red.  According to the Cisco documentation, this indicates a firmware failure.  Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
 
My question is: is there any way to fix the firmware via console?  Whether it be through xmodem or what not.  I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
 
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs.  Shouldn't the status LED be flashing green-amber-red?

View 1 Replies View Related

Linksys Wireless Router :: WRT610N V1 Flashing Power Light / No Wireless / Can't Access Settings

Apr 28, 2012

Everything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
 
Currently I am wired through it with my desktop and its working, but not much else.

View 3 Replies View Related

TP-Link 300Mbps Wireless :: WR1042ND System Light Turns Solid Overnight While There Is No Activity

Feb 18, 2013

Region : Canada
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3.14.4

Recently in the morning the router will have lost ability to connect to internet <internet light is on> and I cannot access the router page <sys light solid> from either wired or wireless connections. Why is this and will it be solved if I upgrade firmware?

View 2 Replies View Related

D-Link DIR-615 :: 5-6 Times A Day Router's Green Internet Light Turn Red

May 31, 2012

For the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.

View 1 Replies View Related

Belkin Routers :: N600 Showing Solid Red Light

Dec 5, 2012

I was having problems connecting to one of my usb devices that was plugged into my router. I unplugged the router to reset it and whenever it starts up it flashes green and the green light goes solid for less then a minute before turning red. It's a solid red light. I've tried unplugging everything and restarting it and nothing. Ironically it still lets me connect to the internet but when I access the control panel on my computer it shows as disconnected. Is this means my router is busted. This is my second Belkin Router and the only reason I had to replace the last one is because it was a G+Mimi router and I upgraded to an N Router.

View 3 Replies View Related

Cisco Firewall :: Solid Amber Status Light On ASA 5505?

Apr 14, 2010

I have a Problem with a ASA 5505 when i power on the ASA  the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.

View 9 Replies View Related

Linksys Wired Router :: Unable To Stop Power Light From Blinking On BEFSR41?

Feb 19, 2011

Unable to stop the power light from blinking on a BEFSR41 tried updating the firmware.I have tried resetting the router using the rest button, for 3 seconds, 10 seconds, and 30 seconds, nothing works.Tried running the setup disk, but it does not see the router.  Is there a repair tool that I can download? 

View 4 Replies View Related

Cisco Wireless :: 3602I Constantly Shows A Fast Blinking Green Light

May 20, 2013

3602I constantly shows a fast blinking green light, watching the boot up I see the following:
 
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
 
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"

View 7 Replies View Related

Cisco Firewall :: Solid Amber Status Light On ASA 5505 Under SmartNet

Oct 14, 2011

I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?

View 2 Replies View Related

Green Ethernet Port Light Always On?

Jun 22, 2011

The green light on my Ethernet port is always on. Even when I unplug the Ethernet cable and shut down my computer. The only way it turns off is when I unplug my computer from the outlet. Also, my computer doesn't receive any internet when an Ethernet cable is plugged in and the yellow flashing light doesn't show either. I know the Ethernet cable is fine and the internet works fine on other computers

View 2 Replies View Related

Routers / Switches :: Green Light Blinking Continuously?

Apr 30, 2011

the router is functional, however the green light has never blinked like it is now.

View 1 Replies View Related

NIC Shows Green Light But Does Not Connect With Other Computer On Network?

Aug 14, 2012

My computer's NIC shows green light but it does not connect with other computer over the network.

View 1 Replies View Related

Linksys Wireless Router :: Internet Light On E3000 Doesn't Light Up?

Jul 22, 2011

 I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!

View 1 Replies View Related

Billion 7800n Internet - Light Drops From Green To Orange?

Jul 24, 2012

my family kept having a problem with our Billion 6800n router. (or something like that).Basically we pinned the problem down to it not having the strength to keep several connections running through it. So we upgraded to a Billion 7800n and found it is much more stable and much faster.However it has been having a similar problem to our previous router.

Occasionally the internet light drops from green to orange, and we can't load any more pages until it has gone back to green.Here is a picture of what it looks like when in that status.But the weird thing is the connection bars on the windows toolbar at the bottom of the screen still show full strength.As shown here.Now I thought it might be because it was sharing a power board with other connections going through it,so I transferred it to a smaller two-plug one instead.

View 2 Replies View Related

Cisco Switching/Routing :: RPS Light Green On 3750 Switch?

Nov 17, 2012

i have standalone 3750 switch. RPS light is green and system light is off.
 
 3750TS#sh env all
FAN is OK
TEMPERATURE is OK

[Code].....
 
i have another switch with same model and ios its RPS light is off and system light is green

View 5 Replies View Related

Linksys Cable / DSL :: WAG120N Red Power Light

Apr 4, 2012

My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !

View 3 Replies View Related

Linksys Wireless Router :: E1000 Solid Blue Lights

Aug 21, 2011

My e1000 router (v 2.1) has reset itself and after that all lights except the wireless adapter has gone solid blue, I have no ethernet conectivity and hard reset the router did not work.

View 9 Replies View Related

Linksys Wireless Router :: BEFW11S4 Reflash Firmware With Solid Red Diag

May 14, 2013

Is it possible to reflash the firmware on a BEFW11S4 (I believe v1, there is no v# after the model number) with a solid red Diag LED? I cannot access the HTML control panel since the router never fully boots. I git this used and didn't know it was **bleep**..

View 2 Replies View Related

ADVERTISEMENT