Cisco Wireless :: AP 1260 Configuration / 0 Clients Connected And Light Always Green
Feb 5, 2013
Recently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
View 1 Replies
ADVERTISEMENT
May 20, 2013
3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
View 7 Replies
View Related
May 27, 2013
i have 2 1260 Access points one is in root mode , one is wgb mode. Authentication is EAPFAST. There are 5 devices connected via WGB bridge to the rest of the network.
- If clients are sending some data , then WGB AP announces this client mac via IAPP to root AP and rest of the network sees them correctly
- If clients are "passive" , then after WBG AP announces them to root AP , they timeout after 6 minutes on root AP and obviously they are not pingable from the rest of the network. The only way to restore connectivity is to ping that device from WGB AP, then WGB AP announces via IAPP to root AP , then and only then they become visible from the rest of the network.
My question is related to this 6 minute timeout on root AP . Is it normal behaviour ?
View 5 Replies
View Related
Nov 20, 2011
I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies
View Related
Jun 22, 2011
The green light on my Ethernet port is always on. Even when I unplug the Ethernet cable and shut down my computer. The only way it turns off is when I unplug my computer from the outlet. Also, my computer doesn't receive any internet when an Ethernet cable is plugged in and the yellow flashing light doesn't show either. I know the Ethernet cable is fine and the internet works fine on other computers
View 2 Replies
View Related
Dec 23, 2012
I have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
View 1 Replies
View Related
Apr 30, 2011
the router is functional, however the green light has never blinked like it is now.
View 1 Replies
View Related
Aug 14, 2012
My computer's NIC shows green light but it does not connect with other computer over the network.
View 1 Replies
View Related
Jun 22, 2011
after several years of proper functioning my WAP started to make trouble and recently stopped working. I've tried a lot of options to get it back online but I failed doing so.The green ACT LED won't light up anymore so my laptop cannot find the WAP anymore. When connecting the WAP directly to the laptop the Network Center shows that Windows is trying to identify the WAP but this messages disappears and re-appears on and on but there is no succes in identification (ofcourse this is caused the the green ACT LED which won't light-up).
View 1 Replies
View Related
Nov 17, 2012
i have standalone 3750 switch. RPS light is green and system light is off.
3750TS#sh env all
FAN is OK
TEMPERATURE is OK
[Code].....
i have another switch with same model and ios its RPS light is off and system light is green
View 5 Replies
View Related
Jul 24, 2012
my family kept having a problem with our Billion 6800n router. (or something like that).Basically we pinned the problem down to it not having the strength to keep several connections running through it. So we upgraded to a Billion 7800n and found it is much more stable and much faster.However it has been having a similar problem to our previous router.
Occasionally the internet light drops from green to orange, and we can't load any more pages until it has gone back to green.Here is a picture of what it looks like when in that status.But the weird thing is the connection bars on the windows toolbar at the bottom of the screen still show full strength.As shown here.Now I thought it might be because it was sharing a power board with other connections going through it,so I transferred it to a smaller two-plug one instead.
View 2 Replies
View Related
May 31, 2012
For the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
View 1 Replies
View Related
Oct 28, 2012
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
View 3 Replies
View Related
May 29, 2012
Recently, our company wireless AP 1262 connected more than 40+ clients, and sometimes the wireless access speed is too slow. those clients are only for MES data transfer, the date no more than 10K of each stations. So I'd like to know if the one AP can support the network traffic if whole testers transfer the data to Database via this wireless AP1262? and the WLC no clients roaming option for which clients can connect to another AP around. I have checked the WLC and AP configuration. no option for clients roaming to another APs, do you know how to configure this AP's Clients move to another APs?If we setup the new APs in the location, does the clients will be auto connect to this new AP?
View 7 Replies
View Related
Feb 12, 2013
I can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems
attempted to fix problems via belkin software
changed channels on modem
updated firmware
etc, etc
View 1 Replies
View Related
Mar 24, 2011
I've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies
View Related
Jun 5, 2012
I have installed an SR520 with wireless for a client. They have asked if there is an easy way for them to monitor who is connected to the wireless at any given point in time. They are not capable of using the IOS command line.
View 1 Replies
View Related
Jan 1, 2013
i have ~ 25 employees which are connected to the AP . I have a 2mb dl and 2mb ul microwave lease line.The AP disconnects ever couple of hours for a minute?
View 3 Replies
View Related
Feb 14, 2013
IP addresses of the clients connected to Wireless end points are not getting resolved in LMS 4.2 user tracking ? Whether LMS will resolve IP addresses of the clients connected through Wireless end points ?
Note : Those wireless end points are not monitored by LMS
View 1 Replies
View Related
May 8, 2013
My question relates to how many clients can be connected to a 2600 series AP. The documentation states 200 clients per radio and the AP has three radios. However when my AP gets to 200 it rejects further clients with the following log: [code] I see this exact message many times and each time the radio mac address is the same and the number of clients connected is 199. The same mac address is used for both 2.4ghz and 5ghz so does this AP have a single logical radio covering both 2.4 and 5ghz frequency ranges and is the limit for all connected clients 200?When viewing the AP details under the Wireless tab it only lists one mac address for each AP for both 2.4ghz and 5ghz frequencies.
View 11 Replies
View Related
Mar 11, 2012
I have 1242AG. how many clients can be connected to this AP??
View 4 Replies
View Related
Mar 16, 2013
is any way to get information about clients connected to an AP WAP200?
View 2 Replies
View Related
May 15, 2013
I just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
No one can connect to the 5 Ghz radio.
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
I am on the latest version of the firmware.
View 1 Replies
View Related
Oct 15, 2012
How many wireless clients can connect to a single WAP321 Access Point?
View 2 Replies
View Related
Feb 2, 2010
I use two wlc 4400 (4.2.x version) with a mobility domain and one ssid, both wlc are connected to a cisco l2 switch infrastructure. On the wlc I use the p2p blocking action 'drop' [URL] to isolate the clients from each other. Does only unicast traffic is blocked or also multicast and broadcast traffic like arp requests?Concerning blocking p2p traffic of clients connected to the same ssid but different controllers I found the following statement in the LAP FAQs [URL]
Q. In autonomous APs, Public Secure Packet Forwarding (PSPF) is used to avoid client devices associated to this AP from inadvertently sharing files with other client devices on the wireless network. Is there any equivalent feature in Lightweight APs?
A. The feature or the mode that performs the similar function of PSPF in lightweight architecture is called peer-to-peer blocking mode. Peer-to-peer blocking mode is actually available with the controllers that manage the LAP. If this mode is disabled on the controller (which is the default setting), it allows the wireless clients to communicate with each other through the controller. If the mode is enabled, it blocks the communication between clients through the controller. It only works among the APs that have joined to the same controller. When enabled, this mode does not block wireless clients terminated on one controller from the ability to get to wireless clients terminated on a different controller, even in the same mobility group.
what's the best practise to prevent this inter wlc client traffic? I already read about using acls on the wlc dynamic interfaces, or private vlans on the l2 switch vlans where the dynamic interfaces are connected to. Is it allowed to completely isolate the wlc from each other on these dynamic interfaces with acls or private vlans or do the wlc need to see each other on this interfaces (e.g. heart beat)?
View 19 Replies
View Related
Jan 27, 2009
I know this question was asked many times, but I'm still not able to finalize my configuration on 871w. LAN part works fine, but wireless clients do not get DHCP IP. here is the config:
Building configuration...
Current configuration : 2092 bytes
!
version 12.4
no service pad
service timestamps debug date time m sec
service timestamps log date time m sec
no service password-encryption
!
[ code ].....
I'd like to have LAN and WLAN clients in same 192.168.1.0 sub net.
View 3 Replies
View Related
Nov 13, 2012
I would like the know if there is a way to know which wireless clients are connected under N mode. There is any kind of command where can show me that ?. I don´t have a wireless controller. My AP is AP-1141N-A-K9
View 2 Replies
View Related
May 21, 2013
My controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows: The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90.
View 3 Replies
View Related
Jul 22, 2011
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies
View Related
May 8, 2013
I just completed installation of a stacked pair of 3850s in my datacenter. While I was installing them, I noticed that the lights on ports 1-8 on one of the switches were on solid even though there were no cables connected to that switch. I don't see anything in the logs or anywhere else in the CLI that indicate a problem, however the lights remain on. This only happens on switch 1, not switch 2. Once I plugged the cable into port 1, it flashes normally with activity, but 2-8 remain on solid even though nothing is connected to them.
Before I put the switches in place, I had configured them at my desk with the console connection, and those lights were not lit up.
The indicators on the front of both switches are set in STAT mode. I thought initially I had hit the button and flipped it to a different mode, but that is not the case.
View 5 Replies
View Related
Nov 17, 2011
Need implementation of an OID to view the number of connected clients per Access-Point? I am using a 5508 WLC.
View 4 Replies
View Related
Apr 17, 2013
I have a TP-Link TD-W8960N Wireless Router. I would like to know what the I.P. addresses of connected clients are (both those connected wirelessly & those connected by Ethernet cable). There are about 6 computers in my network, some have dynamic and others have static I.P. addresses.I am finding it difficult to navigate the router,on which menus get me to the information that I am interested in
View 1 Replies
View Related
Jun 12, 2012
What is the most current version oF IOS for the following Wireless AP(Aironet 1260)
Product/Model Number: AIR-AP1261N-E-K9
System Software Filename: ap3g1-k9w7-tar.124
View 2 Replies
View Related
