Cisco Wireless :: Aironet 1600 Standalone WAP / How To Get Clients Connected
May 15, 2013
I just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
No one can connect to the 5 Ghz radio.
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
I am on the latest version of the firmware.
View 1 Replies
ADVERTISEMENT
Mar 18, 2013
It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies
View Related
Mar 20, 2013
Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 Replies
View Related
Jan 1, 2013
i have ~ 25 employees which are connected to the AP . I have a 2mb dl and 2mb ul microwave lease line.The AP disconnects ever couple of hours for a minute?
View 3 Replies
View Related
Jun 13, 2013
how to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.
View 4 Replies
View Related
Dec 19, 2010
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
View 9 Replies
View Related
Jun 11, 2013
I have a AIR-SAP-1602i-k9 Aironet. I cannot find any information on the Cisco site on how to configure the Aironet without a controller. I assumed a standalone meant I could just login.
I tried seeing if it would pull a DHCP address on my network but it didnt.
View 1 Replies
View Related
Feb 18, 2013
I have to set up the AP in a standalone mode to support voice and data traffic through the wireless network. for this, i was trying to look for the config guide so i know how to go about it, but all the doc was refering to controller based setup. i followed this link URL
I have never worked on wireless in a standalone mode, so this is the first time i will be doing it.
View 22 Replies
View Related
Dec 28, 2011
For some time now I have been looking for a good business class wireless AP. I've narrowed it down to the Cisco Aironet 1140 standalone (no controller). I'm no stranger to Cisco products. I've worked with their routers, switches and Pix/ASA firewalls. However, I've not had the opportunity to work with their wireless AP's. Anyone using these AP's (more specifically the 1140 standalone), can provide information on the reliability and security of these devices. Some of the features I would like to have like Radio Mgmt. and Rogue AP Detection I see are only available on the controller based units. Does not having these features on the standalone unit reduce its reliability and security? This is for a small business and the budget does not allow to drop for a controller at this time.
View 7 Replies
View Related
Sep 13, 2011
I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies
View Related
Aug 7, 2012
I am using an Aironet 1142 standalone AP and want to use Apples Bonjour Service between iOS devices e.g. iPad and Apple TV.I have found here some posts that suggest to disable igmp snopping but this didn't worked for me.All devices are in the same vlan/subnet. Do I need to configure something special?
View 3 Replies
View Related
Mar 19, 2013
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies
View Related
Jul 19, 2012
I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
View 9 Replies
View Related
Oct 12, 2012
We have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.
Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.
View 3 Replies
View Related
Sep 28, 2012
For 2 year now we have been running aironet 1240ag access points throught our warehouse. We use a telnet session on our handheld scanners to connect to our database on the main server.This last week our scanners started getting dropped from the access points serveral times throught the day and often would continue to get dropped at 1 minute intervals for several minutes at a time. This appears to be happening on all of our access points and is affecting all of our scanners but not at the same time.Each time a clinet is dropped we get the following event log on the AP.
Sep 29 11:57:14.807 -0500 Warning Packet to client 0c77.1a3a.6ff7 reached max retries, removing the client
Sep 29 11:57:14.800 -0500 Information Interface Dot11Radio0, Deauthenticating Station 0c77.1a3a.6ff7 Reason: Previous authentication no longer valid
All the AP's are setup the same with the below config
!! Last configuration change at 14:24:18 -0500 Sat Sep 29 2012 by Cisco! NVRAM config last updated at 14:24:18 -0500 Sat Sep 29 2012 by Cisco!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname AP_10!enable secret 5 $1$lcac$OO/IqOlgR2.TPP/BFg7nX1!no aaa new-modelclock timezone -0500 -5!!dot11 syslogdot11 activity-timeout unknown default 128dot11 activity-timeout client default 128dot11 activity-timeout repeater default 128dot11 activity-timeout workgroup-bridge default 128dot11 activity-timeout bridge default 128!dot11 ssid jefferson377 authentication open guest-mode infrastructure-ssid optional!power inline negotiation injector 9caf.ca01.d818power inline negotiation prestandard source!!username Cisco privilege 15
[code]....
View 9 Replies
View Related
Jan 9, 2013
How many maximum clients are supported by cisco aironet 1262 AP and also by a 5500 Wireless Controller?
View 4 Replies
View Related
Aug 17, 2011
I'm setting up a Cisco Aironet 1141 (standalone mode, AP) to handle wireless traffic in the office. It gives out 2 mbssids, one of which authenticates domain users through a RADIUS server and places them in an appropriate VLAN (RADIUS options 64, 65, and 81). The other is a guest ssid that uses WPA-PSK and places users in the restricted guest VLAN. Physically, the AP is connected to a 3750 PoE Catalyst, to which RADIUS and DHCP servers are also connected. AP, SSIDs, RADIUS and EAP authentication all work. The configuration given below is a working configuration. People do get authenticated and do get placed in the appropriate vlan. The problem is that, once authenticated, the "Obtaining IP Address" phase on the client hangs and most clients timeout without getting an IP address. Given that the DHCP server is on the same switch and a test simple ASUS Wi-Fi IP gives out the same scenario (except the multiple VLAN) at the speed of light, I don't think that it's a problem with the network connections between clients and the DHCP server. After reading some topics here, I realized that probably other communication will be extremely slow, as well, but haven't tested that for sure. Clients are all non-Cisco - smartphones, notebooks, etc. Most of them are 802.11G, not N.
View 4 Replies
View Related
Sep 30, 2012
I work for a small college. We have several Cisco 1200 Aironet deployed our the campus, all of which are configures to run multiple SSID's. The problem I have is that when I connect, via AP, it successfully connects to the desired SSID but on pinging the default gateway of said SSID I get high latency (avg around 100 - 200ms).When pinging from the switch (Cisco 2950) to the default gateway the latency is good (1-2ms). It is just high when I connect via the C1200 AP and try to ping.
View 1 Replies
View Related
Jun 5, 2012
I have installed an SR520 with wireless for a client. They have asked if there is an easy way for them to monitor who is connected to the wireless at any given point in time. They are not capable of using the IOS command line.
View 1 Replies
View Related
Feb 14, 2013
IP addresses of the clients connected to Wireless end points are not getting resolved in LMS 4.2 user tracking ? Whether LMS will resolve IP addresses of the clients connected through Wireless end points ?
Note : Those wireless end points are not monitored by LMS
View 1 Replies
View Related
May 8, 2013
My question relates to how many clients can be connected to a 2600 series AP. The documentation states 200 clients per radio and the AP has three radios. However when my AP gets to 200 it rejects further clients with the following log: [code] I see this exact message many times and each time the radio mac address is the same and the number of clients connected is 199. The same mac address is used for both 2.4ghz and 5ghz so does this AP have a single logical radio covering both 2.4 and 5ghz frequency ranges and is the limit for all connected clients 200?When viewing the AP details under the Wireless tab it only lists one mac address for each AP for both 2.4ghz and 5ghz frequencies.
View 11 Replies
View Related
Mar 11, 2012
I have 1242AG. how many clients can be connected to this AP??
View 4 Replies
View Related
Mar 16, 2013
is any way to get information about clients connected to an AP WAP200?
View 2 Replies
View Related
Oct 15, 2012
How many wireless clients can connect to a single WAP321 Access Point?
View 2 Replies
View Related
Feb 2, 2010
I use two wlc 4400 (4.2.x version) with a mobility domain and one ssid, both wlc are connected to a cisco l2 switch infrastructure. On the wlc I use the p2p blocking action 'drop' [URL] to isolate the clients from each other. Does only unicast traffic is blocked or also multicast and broadcast traffic like arp requests?Concerning blocking p2p traffic of clients connected to the same ssid but different controllers I found the following statement in the LAP FAQs [URL]
Q. In autonomous APs, Public Secure Packet Forwarding (PSPF) is used to avoid client devices associated to this AP from inadvertently sharing files with other client devices on the wireless network. Is there any equivalent feature in Lightweight APs?
A. The feature or the mode that performs the similar function of PSPF in lightweight architecture is called peer-to-peer blocking mode. Peer-to-peer blocking mode is actually available with the controllers that manage the LAP. If this mode is disabled on the controller (which is the default setting), it allows the wireless clients to communicate with each other through the controller. If the mode is enabled, it blocks the communication between clients through the controller. It only works among the APs that have joined to the same controller. When enabled, this mode does not block wireless clients terminated on one controller from the ability to get to wireless clients terminated on a different controller, even in the same mobility group.
what's the best practise to prevent this inter wlc client traffic? I already read about using acls on the wlc dynamic interfaces, or private vlans on the l2 switch vlans where the dynamic interfaces are connected to. Is it allowed to completely isolate the wlc from each other on these dynamic interfaces with acls or private vlans or do the wlc need to see each other on this interfaces (e.g. heart beat)?
View 19 Replies
View Related
Feb 5, 2013
Recently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
View 1 Replies
View Related
Nov 13, 2012
I would like the know if there is a way to know which wireless clients are connected under N mode. There is any kind of command where can show me that ?. I don´t have a wireless controller. My AP is AP-1141N-A-K9
View 2 Replies
View Related
May 21, 2013
My controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows: The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90.
View 3 Replies
View Related
May 22, 2013
Does the access point 1600 and 2600 support flexconnect mode?
View 5 Replies
View Related
Nov 17, 2011
Need implementation of an OID to view the number of connected clients per Access-Point? I am using a 5508 WLC.
View 4 Replies
View Related
Feb 6, 2013
I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 15 Replies
View Related
Apr 1, 2013
I have a Airnet 1600 Series that I want to add as another repeater to our 1200 series 802.11g network. We already have 2 AP's running fine as Repeater and BR, I just need to a this 1600 AP to the existing wirelss. Everytime I try to change the 1600ap as a repeater, I get the below error.
cannot set role in radio network to when another radio is set to one of the above roles
View 1 Replies
View Related
Apr 21, 2013
Does Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge? I read the release notes 15.2 but I couldn't find it.
View 7 Replies
View Related
