Cisco Wireless :: Universal Workgroup Bridge On CleanAir 1600?

Apr 21, 2013

Does Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge?  I read the release notes 15.2 but I couldn't find it. 

View 7 Replies


ADVERTISEMENT

Cisco Wireless :: 1600 Series AP Cannot Enable CleanAir In Global

Feb 6, 2013

I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined.  This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir?  If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?

View 15 Replies View Related

Cisco Wireless :: AP1121G Workgroup Bridge

Feb 12, 2012

Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
 
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction. Also attached is a result table of ping attempts through the ap1121wgb from each side. I don't have a problem with the wireless connections. The ap1121g's associate ok. Based on the ping results the problem appears to be in the ap1121g-wgb configuration. The following two cisco documents have been my main reference, besides the cisco command lookup site.URL

View 17 Replies View Related

Cisco Wireless :: Using 1262 AP In Workgroup Bridge Mode?

Nov 18, 2012

Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX.   They do not want to dig up the parking lot so we proposed using a wireless bridge.   I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge.   Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions?   I will put a Layer 3 switch on both ends to route traffic (3560C-8).   Should I use the Yagi antenna's for outdoor use? 

View 1 Replies View Related

Cisco Wireless :: WorkGroup Bridge / Which Mode To Use - WET610N

Feb 21, 2012

We have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.

View 1 Replies View Related

Cisco Wireless :: WAP121 Workgroup Bridge Mode

Feb 16, 2013

I have an old computer with dead wifi nc and I thought that bridging it with was121 should work, but can't find anywhere any comprehensive documentation on how to set it up.

View 1 Replies View Related

Cisco Wireless :: Workgroup Bridge Between WRVS440n And WAP321?

Dec 4, 2012

i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
 
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
 
Network Interface Status and Statistics VLAN ID Name (SSID)  
WLAN0UPSTRM  Disconnected  1  myssid   
WLAN0DWSTRM  Up  1  myssid
 
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected

View 6 Replies View Related

Cisco Wireless :: C1310 Workgroup Bridge Sample Configuration

Mar 18, 2013

Any sample configuration of c1310 as a work group bridge.

View 2 Replies View Related

Cisco Wireless :: Max Number Of Clients For 1242 Setup As Workgroup Bridge?

Nov 14, 2012

I have Cisco 1242 setup as a work group bridge. Is there a rule of thumb on the max number of wired clients that can be connected at one time?

View 1 Replies View Related

Cisco Switching/Routing :: 4900M Downgrade IOS From Universal 15.x To Non-Universal 12.x

Aug 14, 2012

Is it possible to downgrade the 4900M IOS image from Universal 15.x image to non-Universal (possibly IP BASE) 12.x image.

View 1 Replies View Related

Cisco Wireless :: 1262N AP Disables Radios When Switched To Workgroup Bridge Mode

Feb 21, 2013

I am trying to enable the workgroup bridge mode on the 5ghz 802.11N radio of a Aironet 1262N, but when I select the workgroup bridge mode from the GUI the radio becomes disabled.  If I select the Access Point role from the GUI then the radio instantly becomes enabled.  The same thing happens if I attempt the same procedure with the 2.4ghz radio as well.  I can get the radios from both bands enabled if I select the Access Point role.  I made sure to check that both radios were not set to workgroup bridge as well.  I am running 12.4(25d)JA1 code on the AP.  This is my first time working with this type of AP.

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Workgroup Bridge Authentication With ACS 5.x?

Nov 5, 2012

EAP-TLS authentication for workgoup brdige fails.
 
Folloing is the log on ACS
Authentication failed
12514 EAP-TLS failed  SSL/TLS handshake because of an unknown CA in the client certificates chain
 12811 Extracted TLS Certificate message containing client certificate.
12814 Prepared TLS Alert message.
12817 TLS handshake failed.

[code]....

View 1 Replies View Related

Cisco :: NCS And 3500 With CleanAir - Not Seeing Data?

Mar 6, 2012

we demo'd a 3500 with CleanAir before working with Cisco and purchasing a first batch.  The demo worked as expected, just plugged it in and it went to town serving clients and reporting on it's channel in local mode, no problem.  My first batch I have two AP's, 3502i's to be exact, plugged in and running on my 5508 with 7.0.98.0 code and and NCS Demo.  The AP is up and serving in local mode, however NCS says CleanAir Management Operation StateDown 
 
I took a look at the WLC and it says:

CleanAir
Oper
Status               DOWN
  
So, why.. and where do I put it UP.BTW, this AP is connected to a 3750x stack, shouldn't be an issue there...

View 3 Replies View Related

Cisco Wireless :: FlexConnect Support For AP 1600 And 2600?

May 22, 2013

Does the access point 1600 and 2600 support flexconnect mode?

View 5 Replies View Related

Cisco Wireless :: Setting Up Aironet 1600 Series

Jun 13, 2013

how to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.

View 4 Replies View Related

Cisco Wireless :: Aironet 1600 - Standalone Or Autonomous

Mar 18, 2013

It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?        

View 3 Replies View Related

Cisco Wireless :: Adding 1600 To Existing 1200 AP Network?

Apr 1, 2013

I have a Airnet 1600 Series that I want to add as another repeater to our 1200 series 802.11g network. We already have 2 AP's running fine as Repeater and BR, I just need to a this 1600 AP to the existing wirelss. Everytime I try to change the 1600ap as a repeater, I get the below error.
 
cannot set role in radio network to when another radio is set to one of the above roles

View 1 Replies View Related

Cisco Wireless :: 1600 Series AP To Reset Before Joining To Controller

Mar 3, 2013

I have new 1600 series Access Points. I am trying to join those APs on controller but unable to join.
 
After doing config reset using mode button, I was able to join only. Please find the logs or error messages below:
 
*Mar  4 18:53:13.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.2.241.50:5246
*Mar  4 18:53:14.063: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar  4 18:53:14.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar  4 18:53:14.123: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
[Code] ....

View 6 Replies View Related

Cisco Wireless :: 1600 / 2600 With Single External Antenna?

Jun 5, 2013

I have an unusual request to support an access point with a single external antenna to cover a small physical area (elevator car!!). All Cisco's currently shipping APs have dual band antennas using MIMO for throughput in "normal" deployments. Will a deployment with a single antenna work?

View 2 Replies View Related

Cisco Wireless :: Aironet 1600 Standalone WAP / How To Get Clients Connected

May 15, 2013

I just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
 
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
 
No one can connect to the 5 Ghz radio.
 
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
 
I am on the latest version of the firmware.

View 1 Replies View Related

Cisco Wireless :: 871W In Universal Client Mode Bridging

Jul 21, 2008

I have a 1242 Access Point as root and a 871W Router as a non-root bridge (Diagram attached). I have a laptop connected to Fa 0 of the 871W router.
 
* I am able to ping from the AP to the Router and vice versa
* I am also able to ping from the router to the laptop and vice versa
* But I am not able to ping from the laptop to the AP
 
All bridging commands seem to be fine. Even tried adding route commands, but none seem to work.Please find the configuration below:
 
Configuration on Root AP:

hostname ap
!
enable secret 5 XX
!
[Code]....

View 4 Replies View Related

Cisco Wireless :: 1600 AP Series Cannot Enable Clean Air In Global Parameters

Jan 8, 2013

I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined.  This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir?  If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?

View 9 Replies View Related

Cisco Wireless :: WAP4410 Doesn't Just Make A Universal Power Injector

Oct 10, 2011

Contrary to the information contained in the link above, these two parts do not play well together. I purchased both and plugged them in and no go. It doesn't even light anything on the WAP. It worked fine when it was on its own 12V DC adapter but not plugged into this injector. What I don't understand is why Cisco doesn't just make a Universal power injector that is essentially a 1 port switch and is 802.3af or 802.3at compatible. Its maddening. It looks like I'm going to have to get an SD208P and waste 6 ports just to get one with the correct POE for the WAP4410.

View 2 Replies View Related

Cisco Wireless :: Convert Standalone 1600 Access Point To CAPWAP Based AP

Mar 20, 2013

Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs

View 1 Replies View Related

Belkin Routers :: How To Setup Universal Wireless HDTV Adapter F7D4555v1

Dec 11, 2012

Could not find on Belkin website, hyperlink came up with "oops' result. Basic instructions to hook this up to my TV.

View 1 Replies View Related

Cisco LAN :: How To Do Port Forwarding For 1600

Mar 26, 2012

We have a Cisco 1600 Router, would like to know how to do port forwarding to allow our security camera to be able to view online

View 1 Replies View Related

Cisco Wireless :: Maximum Code Level For Lightweight 1130 / Minimum WLC Code For 1600 Series APs?

Feb 19, 2013

I have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?

View 3 Replies View Related

Universal LAN Drivers For Windows 7?

Sep 30, 2012

I need universal lan driver for windows 7

View 3 Replies View Related

Getting TP-Link Universal Repeater Setup?

Mar 22, 2012

facing issues with TP-Link TL-WA801ND while setting it up as a Universal repeater.The AP is a Linksys E3200..and I got the TP-Link to broaden my WiFi at home, I was successful in setting it up, however, after a day or two I get prompted to enter a "WPA2 Enterprise" username/password.I DID NOT setup WPA2 Enterprise, mine is WPA2 Personal...it's peculiar that it works for a bit then reverts to Enterprise.

View -1 Replies View Related

Belkin 54g Universal Repeater Not Working?

Mar 19, 2011

I've been using a Belkin 54g Universal Repeater for around a year and a half to extend my wireless connection around the house but recently it's stopped working completely. The red "Searching" light is flashing constantly and it doesn't register with my computer anymore. I've tried connecting it to my main router and to my computer via ethernet to no avail.

View 1 Replies View Related

Wireless :: Can't See Other PCs On XP Workgroup?

May 9, 2011

My partner and I have 2 notebook PCs and we have a wireless moden/router. I used to see my partner's PC in the Workgroup and share the printer before I reloaded windows XP Home in partner's PC. I added his PC to the Workgroup but can't see him in Workgroup from my PC anymore?

View 2 Replies View Related

Wireless :: How To Set Up A Workgroup

Jul 21, 2011

I have an older Linksys 11g router, two pc's with Windows 7 and a bunch of PC's with Windows XP that I need to LAN.Is there a simple way to do it?

View 1 Replies View Related

Cisco WAN :: L2TPV3 Pseudo-wire 1921 Universal Image

Aug 8, 2011

come to a bit of a block in the road on a network im building ,all is going well except i need to build a pseudowire to backup our primary L2 circuit, I labbed this with some 3745's but the kit we are using is the 1921, with the universal image how do i go about upgrading functionality to allow this [code]

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved