Cisco Wireless :: FlexConnect Support For AP 1600 And 2600?
May 22, 2013Does the access point 1600 and 2600 support flexconnect mode?
View 5 Replies
ADVERTISEMENT
Cisco Wireless :: 1600 / 2600 With Single External Antenna?
Jun 5, 2013I have an unusual request to support an access point with a single external antenna to cover a small physical area (elevator car!!). All Cisco's currently shipping APs have dual band antennas using MIMO for throughput in "normal" deployments. Will a deployment with a single antenna work?
View 2 Replies View RelatedCisco Wireless :: 5508 / 3600 / 2600 - Configuring HP Switches For FlexConnect?
Apr 27, 2013Configuring HP switches for Flexconnect. I am not sure if or not its doable? Access Points are 2600 and 3600 with 5508 as a controller. Idea is to keep the branch traffic local but the switches are HP.
View 3 Replies View RelatedCisco Wireless :: Does Aironet Autonomous 2600 Support WDS
Mar 20, 2013Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
Cisco Switching/Routing :: Does 2600 Series Switch Support 802.1x And DHCP Snooping
Feb 14, 2012does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies View RelatedCisco WAN :: Will 2600 Series Router Support 10Mb 10 / 1000 Traffic From New Modem
Jun 26, 2012We are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies View RelatedCisco Wireless :: Setting Up Aironet 1600 Series
Jun 13, 2013how to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.
View 4 Replies View RelatedCisco Wireless :: Aironet 1600 - Standalone Or Autonomous
Mar 18, 2013It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies View RelatedCisco Wireless :: 1600 Series AP Cannot Enable CleanAir In Global
Feb 6, 2013I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 15 Replies View RelatedCisco Wireless :: Adding 1600 To Existing 1200 AP Network?
Apr 1, 2013I have a Airnet 1600 Series that I want to add as another repeater to our 1200 series 802.11g network. We already have 2 AP's running fine as Repeater and BR, I just need to a this 1600 AP to the existing wirelss. Everytime I try to change the 1600ap as a repeater, I get the below error.
cannot set role in radio network to when another radio is set to one of the above roles
Cisco Wireless :: Universal Workgroup Bridge On CleanAir 1600?
Apr 21, 2013Does Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge? I read the release notes 15.2 but I couldn't find it.
View 7 Replies View RelatedCisco Wireless :: 1600 Series AP To Reset Before Joining To Controller
Mar 3, 2013I have new 1600 series Access Points. I am trying to join those APs on controller but unable to join.
After doing config reset using mode button, I was able to join only. Please find the logs or error messages below:
*Mar 4 18:53:13.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.2.241.50:5246
*Mar 4 18:53:14.063: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 4 18:53:14.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 4 18:53:14.123: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
[Code] ....
Cisco Wireless :: Aironet 1600 Standalone WAP / How To Get Clients Connected
May 15, 2013I just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
No one can connect to the 5 Ghz radio.
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
I am on the latest version of the firmware.
Cisco Wireless :: 1600 AP Series Cannot Enable Clean Air In Global Parameters
Jan 8, 2013I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 9 Replies View RelatedCisco Wireless :: Convert Standalone 1600 Access Point To CAPWAP Based AP
Mar 20, 2013Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 Replies View RelatedCisco Wireless :: 3602i / ClientLink On A FlexConnect AP?
Feb 18, 2013I have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows "Hardware beamforming stats not supported (radioid 0x3B00)" message instead of show the client information. I am using a 2504 Wireless LAN Controller running 7.3.101.0 software version, why is not working properly?
View 7 Replies View RelatedCisco Wireless :: Mesh And Flexconnect With WLC5508?
Apr 4, 2013A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
Cisco Wireless :: 2504 WLC / Flexconnect APs Stopped Joining?
May 12, 2013A customer of mine has a centralized 2504 WLC with 7.2 code running. They have 1142N APs deployed locally as well as in remote sites (3) in FlexConnect mode. For no apparent reason last Thursday all the remote APs disassociated with the controller and could not rejoin. All the local APs remained up and unaffected.No changes to the WLAN, LAN, Firewall or MPLS WAN occured to cause this.The customer opened a TAC case and their determination was that ports 5246-5247 were not getting thru. When the customer engaged me this morning I had him run a packet capture on the Sonicwall firewall to prove out if the CAPWAP signals were leaving and returning across the WAN. Sure enough we can see this bi-directional traffic (pic attached). Also, I had the MPLS provider run a trace at the far end and they see the same traffic leave the remote site. And then an odd thing happened; one of the APs at one of the remote sites all of a sudden Joined the controller. So I tried rebooting the AP that is located in the same office, and it fails to Join. When I look on the controller under AP Join statistics, the last activity shows the controller receiving a Discovery Request and response is sent, but no further Config Request and response or Join Request and response.
View 8 Replies View RelatedCisco Wireless :: 1242 - FlexConnect Client Connectivity
May 31, 2013However, I now have a number of devices... certain smartphones so far... that will NOT connect to a FlexConnect AP if it's a 1262AGN AP, but my older 1242G AP will accept the devices without issue. Same SSID, same encryption standards.
If I connect the devices to my guest network (no security), they will connect just fine to both APs, and Non-FlexConnect 1242 and 1262 APs will both accept the devices without issue using my private network.
In other words, it seems to be an issue specific to 1262AGN with my encryption security. My security is WPA2/AES with PSK. No additional security on the SSID.
Cisco :: Wireless Phones 7925 No Voice With Flexconnect
May 22, 2013We have a problem when I call bettween two 7925 in same SSID, VLAN voice. They cannot hear each other. The SSID and LAPs are in Flexconnet. From desk phones there are no problem and betwen one deskphone and one wireless phone there no problem too.
View 2 Replies View RelatedCisco Wireless :: 3600 - Use FlexConnect In Same Network Where WLC Located?
Feb 3, 2013I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
Cisco Wireless :: WLC 2504 FlexConnect Loose Connectivity With GW
Nov 29, 2012I have one WLC 2504 with 7.3.101.0 code and 4 APs 1142 in Flexconnect mode all of them are in one group with 2 SSIDs in two differents VLAN:
-Admin VLAN 151
-Corporate VLAN 158
-Guest VLAN 159
-The auth is 802.1x using an ACS ver 4.2
I connect my Laptop to the corporate SSID and start to have access to web services, intranet services, etc but arround 15 25 min after i connect i lost connectivity to my GW and all the services but i still have my IP info. I do some tests on MAC books, Laptop with Windows XP, 7 and 8 and its the same for all. I config one switch port in the corporate VLAN and i never loose connectivity.
If i reset the WLAN connection all start to works.The ports in the SW are in trunk mode and almost always the APs are in connect mode.
Cisco Wireless :: 1130AG APs / VWLC 7.4 LAP Flexconnect Configuration
Feb 17, 2013i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies View RelatedCisco Wireless :: 1042n And 1142n Macintosh Cannot Connect Using Flexconnect
Aug 22, 2012I have about 200 APs (Cisco 1042n and 1142n), 4 controllers (5508 and 2504).. Switches are 2960s and some other stuff.. I Use NCS for management.We have a couple of vlans and SSIDs, when users connect to a SSID i use Flexconnect to associate the users to the correct VLAN.
View 5 Replies View RelatedCisco Wireless :: Hreap And Flexconnect After WLC 5500 Software Upgrade
Apr 8, 2013I have quick question about wlc software version upgrade : currect version of 5500 WLC : 7.0.220.0,However i am planning to upgrade to version 7.2.110.0,currectly all remote site AP's are connected to this WLC , nearly 150 AP's all are in H-reap mode however once i upgrade to 7.2.110.0 version , all default should come into Flexconnect mode.Do i need to make any configuration or any changes in AP's to get Flexconnect mode or will it be default mode as Flexconnect mode in new version of WLC ?
View 1 Replies View RelatedCisco Wireless :: 1130 - Flexconnect In Central Switch Not Working
May 1, 20131) Virtual controller 7.3.112 is OK
2) N° 2 LAP 1130 e 1240 is Joined to controller OK
3) flexconnect in localswitch is OK
4) flexconnect in central switch IS NOT work.
Cisco Wireless :: 5508 / FlexConnect Compatibility With Access Point
Apr 22, 2013Subject: FlexConnect compatibility with Access Point? We have today one Cisco 5508 and those access point on remote sites
o CISCO AIR-LAP-1131AG-E-K9
o CISCO AIR-LAP-1231G-E-K9
o CISCO AIR-LAP-1142N-E-K9
We plan to use redundancy on the controller and implement Flexconnect on the remote site. What we need to know is if I can implement Flexconnect on all actual access point - I think it is possible on 1142N + 1131G but do not know on 1231AG - is it correct or I'm wrong ? We plan to install the latest SW version for 5508 controller.
Cisco Wireless :: 5508 / AP Flexconnect - Switch Port Configuration?
Jul 23, 2012I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP.
At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same controller for connecting one of the remote sites with 2 APs in FlexConnect mode. Current the 5508 to switch port is configured as 802.1Q port. All CAPWAP AP ports are configured as "switchport access vlan X" where X=capwap VLAN. Need to know how the switch port should be set for the remote site where flexconnect APs connect.
Cisco Wireless :: WLC 8500 / Sticky Key Caching Flexconnect Access Points?
Jun 13, 2013The wlc config guide of Release 7.4 states that sticky key caching (usefull with apple devices) is supported at AP in local mode. [URL]I am testing the new WLC 8500 with 7.4.100.60.
AP mode = FlexConnect
The wlan i activated skc is centrally switched.I debugged the iPhone (4S) roaming.I think skc works at centrally switched vlan on flexconnect APs.
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Reassociation received from mobile on BSSID 00:16:9c:ba:a9:b6
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Global 200 Clients are allowed to AP radio
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Max Client Trap Threshold: 0 cur: 23
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Rf profile 600 Clients are allowed to AP wlan
[code]....
Cisco Wireless :: 7.4.100.0 / MDNS Profiling Cannot Be Enabled With Flexconnect Local Switching
Feb 20, 2013after upgrading to 7.4.100.0 im getting this error message when trying to apply changes on the wlan id."mDNS profiling cannot be enabled with flexconnect local switching"if unselect mDNS snooping under (wlan id/advanced) i can apply the changes, but only temporary.when im looking the next time, the tick box mDNS snooping is enabled again.is this a bug or what?
View 7 Replies View RelatedCisco Wireless :: 2602 Check Box Under Wlan For FlexConnect Local Authentication
Apr 4, 2013I have several 2602 AP's that I want to operate in FlexConnect mode. The WLC is at a central HQ and the Ap's are remote. There are central radius servers at the HQ for the wlans. At the remote lcoation, there is a local radius server we want to use for the primary radius server for these AP's. This radius server has been added to the WLC. I have setup a FlexConnect Group, designated the the primary and secondary servers, and then added the AP's to the group. It does not look like radius requests are being sent to the local controller.
For this to work, do we have to check the box under the wlan for FlexConnect Local Auth? Currently, we only have FlexConnect local switching selected.
Cisco Wireless :: Integrate ISE And WLC5508 With FlexConnect (local Switching) Using EAP-TLS Security?
Nov 29, 2012I need to integrate Cisco ISE and WLC5508 with FlexConnect (local switching) using EAP-TLS security for wireless clients across multiple floors (dynamic VLAN assignments based on floor level). The AP model used is 3602.
- What RADIUS Attribute can be used for dynamic VLAN assignments based on floor level? Is there an option where I can group all LWAPs in same floor for getting certain VLAN from ISE?
- I intend to use WLC software version 7.2 since 7.3 is latest version. Has someone use WLC software version 7.3 without any major bugs/issues pertaining to FlexConnect and EAP-TLS?
- I read some documents saying L3 roaminig is where the associated WLC has changed. However if user move to different subnet but still associated to the same WLC, would this be consider as L3 roaming too?
Cisco LAN :: How To Do Port Forwarding For 1600
Mar 26, 2012We have a Cisco 1600 Router, would like to know how to do port forwarding to allow our security camera to be able to view online
View 1 Replies View Related