We have a problem when I call bettween two 7925 in same SSID, VLAN voice. They cannot hear each other. The SSID and LAPs are in Flexconnet. From desk phones there are no problem and betwen one deskphone and one wireless phone there no problem too.
View 2 Repliesprovide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
I have a CUCM BE environment with a number of remote users with 8961 phones connecting to an ASA 5501 via AnyConnect. The phones register fine and can make inbound/outbound calls as well as four digit dialing to other users at the corporate site.
The problem is when a remote user tries to four digit dial another remote phone. The called phone will ring but there is dead air once answered and then the line goes dead.
This sounds like a routing issue to me. How to get AnyConnect clients to be able to reach each other?
have configured Cisco IPPhone 7925G with EAP-TLS setting. (With manufacture installed and Userinstalled certificate). My issue is while roaming from 1 AccessPoint to another AccessPoint the call getting droped. I need to restart the IPPhone to reauthentiate again. In ACS am agging the authentication time-out error. (I had changed the time out value for EAP-TLS to 20 in WLC as per recommendation.)
If am using static web key there is no issue in roaming.
What is the reommended setting inorder for the EAP-TLS to work properly.
I have a customer that have trouble with the update of the position of a client. Even if the clients walks across the whole building, the client will stay at the same place for several minutes. Is there any way to tune the refresh rate? When I push the load button in the map, the clients position will refresh, or it did when I was on the site, now they just test with an application.
The setup:
WiSM 7.0.220
WCS 7.0.220
MSE 7.0.220
They use the API for MSE to get the location information to the external application, and that will show the information on a cisco 7925 IP phone.know a way to increasing the refresh rate?
recently we have deployed a Two APs in branch office warehouse and I have one wifi phone 7925 used over there. the problem is every time when phone roaming from one AP to another, 2 or 3 packets dropped, following is result of the 'debug client ':
--More or (q)uit current module or <ctrl-z> to abort*apfMsConnTask_7: Jun 27 09:52:25.496: 88:43:e1:4f:ab:39 Association received from mobile on AP a0:cf:5b:c3:a8:90*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 10.107.38.121 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying site-specific IPv6 override for station 88:43:e1:4f:ab:39 - vapId 14, site 'AKL-AP-GP', interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying IPv6 Interface Policy for station 88:43:e1:4f:ab:39 - vlan 38, interface id 0, interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39
[code]....
How to get the FCC ID from a 7925 phone. We have one on order for an upcoming VoFi site survey but I wanted to take a look at the maximum output power by channel so I can begin cell/channel planning.
View 2 Replies View RelatedI have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows "Hardware beamforming stats not supported (radioid 0x3B00)" message instead of show the client information. I am using a 2504 Wireless LAN Controller running 7.3.101.0 software version, why is not working properly?
View 7 Replies View RelatedA customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
I have an issue with the 7925 phones. We have a Cisco Call Manager with a couple of access points and a wireless lan controller. But we have at some points some sort of hole in the sound. He doesn't loose it's connection because i don't hear the beep when he's out of range. And according to the phone he still has a connection with the access point. But there is no sound anymore. And if i walk a couple of meters further i got sound again. If i walk back i somehow get in the same hole and loose the sound. Further back in i got sound back.
I know when it comes to WiFi that there can be some sort of blind spot but there isn't. He still has it's connection with the AP. Is there a value regarding de RSSI value that he needs to have to get a normal speech?
Does the access point 1600 and 2600 support flexconnect mode?
View 5 Replies View RelatedA customer of mine has a centralized 2504 WLC with 7.2 code running. They have 1142N APs deployed locally as well as in remote sites (3) in FlexConnect mode. For no apparent reason last Thursday all the remote APs disassociated with the controller and could not rejoin. All the local APs remained up and unaffected.No changes to the WLAN, LAN, Firewall or MPLS WAN occured to cause this.The customer opened a TAC case and their determination was that ports 5246-5247 were not getting thru. When the customer engaged me this morning I had him run a packet capture on the Sonicwall firewall to prove out if the CAPWAP signals were leaving and returning across the WAN. Sure enough we can see this bi-directional traffic (pic attached). Also, I had the MPLS provider run a trace at the far end and they see the same traffic leave the remote site. And then an odd thing happened; one of the APs at one of the remote sites all of a sudden Joined the controller. So I tried rebooting the AP that is located in the same office, and it fails to Join. When I look on the controller under AP Join statistics, the last activity shows the controller receiving a Discovery Request and response is sent, but no further Config Request and response or Join Request and response.
View 8 Replies View RelatedHowever, I now have a number of devices... certain smartphones so far... that will NOT connect to a FlexConnect AP if it's a 1262AGN AP, but my older 1242G AP will accept the devices without issue. Same SSID, same encryption standards.
If I connect the devices to my guest network (no security), they will connect just fine to both APs, and Non-FlexConnect 1242 and 1262 APs will both accept the devices without issue using my private network.
In other words, it seems to be an issue specific to 1262AGN with my encryption security. My security is WPA2/AES with PSK. No additional security on the SSID.
I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
I have one WLC 2504 with 7.3.101.0 code and 4 APs 1142 in Flexconnect mode all of them are in one group with 2 SSIDs in two differents VLAN:
-Admin VLAN 151
-Corporate VLAN 158
-Guest VLAN 159
-The auth is 802.1x using an ACS ver 4.2
I connect my Laptop to the corporate SSID and start to have access to web services, intranet services, etc but arround 15 25 min after i connect i lost connectivity to my GW and all the services but i still have my IP info. I do some tests on MAC books, Laptop with Windows XP, 7 and 8 and its the same for all. I config one switch port in the corporate VLAN and i never loose connectivity.
If i reset the WLAN connection all start to works.The ports in the SW are in trunk mode and almost always the APs are in connect mode.
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies View RelatedI'm currently in the process of the setting up a new wireless network and I want to test out our 7925 phones on it. When I try uploading the certificate to the phone it fails and I find the following error in the trace logs
[code]...
I created this certificate using using Windows Server 2003 and it is 2048 bits. This certificate works fine with my laptop but I'm unable to upload it to the phone. The app load currently on the phone is CP7925-MFG-D.8.LOADS. Are there any specific guidelines out there when creating a certificate for a Cisco 7925 phone?
I have about 200 APs (Cisco 1042n and 1142n), 4 controllers (5508 and 2504).. Switches are 2960s and some other stuff.. I Use NCS for management.We have a couple of vlans and SSIDs, when users connect to a SSID i use Flexconnect to associate the users to the correct VLAN.
View 5 Replies View RelatedI have quick question about wlc software version upgrade : currect version of 5500 WLC : 7.0.220.0,However i am planning to upgrade to version 7.2.110.0,currectly all remote site AP's are connected to this WLC , nearly 150 AP's all are in H-reap mode however once i upgrade to 7.2.110.0 version , all default should come into Flexconnect mode.Do i need to make any configuration or any changes in AP's to get Flexconnect mode or will it be default mode as Flexconnect mode in new version of WLC ?
View 1 Replies View Related1) Virtual controller 7.3.112 is OK
2) N° 2 LAP 1130 e 1240 is Joined to controller OK
3) flexconnect in localswitch is OK
4) flexconnect in central switch IS NOT work.
Subject: FlexConnect compatibility with Access Point? We have today one Cisco 5508 and those access point on remote sites
o CISCO AIR-LAP-1131AG-E-K9
o CISCO AIR-LAP-1231G-E-K9
o CISCO AIR-LAP-1142N-E-K9
We plan to use redundancy on the controller and implement Flexconnect on the remote site. What we need to know is if I can implement Flexconnect on all actual access point - I think it is possible on 1142N + 1131G but do not know on 1231AG - is it correct or I'm wrong ? We plan to install the latest SW version for 5508 controller.
I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP.
At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same controller for connecting one of the remote sites with 2 APs in FlexConnect mode. Current the 5508 to switch port is configured as 802.1Q port. All CAPWAP AP ports are configured as "switchport access vlan X" where X=capwap VLAN. Need to know how the switch port should be set for the remote site where flexconnect APs connect.
Using Sha1 for Cisco 7925g and sha256 for data. Two separate CA's, one EnTrust (SHA1) the other Local Wondows CA (SHA256); ISE can only use one at a time to process a particular protocol (ie..EAP-TLS, HTTP, etc...) As a result we have to have a separate PSN just for Wireless and Wired VoIP (which can only hold SHA1 RSA1024).
View 5 Replies View RelatedConfiguring HP switches for Flexconnect. I am not sure if or not its doable? Access Points are 2600 and 3600 with 5508 as a controller. Idea is to keep the branch traffic local but the switches are HP.
View 3 Replies View RelatedThe wlc config guide of Release 7.4 states that sticky key caching (usefull with apple devices) is supported at AP in local mode. [URL]I am testing the new WLC 8500 with 7.4.100.60.
AP mode = FlexConnect
The wlan i activated skc is centrally switched.I debugged the iPhone (4S) roaming.I think skc works at centrally switched vlan on flexconnect APs.
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Reassociation received from mobile on BSSID 00:16:9c:ba:a9:b6
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Global 200 Clients are allowed to AP radio
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Max Client Trap Threshold: 0 cur: 23
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Rf profile 600 Clients are allowed to AP wlan
[code]....
after upgrading to 7.4.100.0 im getting this error message when trying to apply changes on the wlan id."mDNS profiling cannot be enabled with flexconnect local switching"if unselect mDNS snooping under (wlan id/advanced) i can apply the changes, but only temporary.when im looking the next time, the tick box mDNS snooping is enabled again.is this a bug or what?
View 7 Replies View RelatedI have several 2602 AP's that I want to operate in FlexConnect mode. The WLC is at a central HQ and the Ap's are remote. There are central radius servers at the HQ for the wlans. At the remote lcoation, there is a local radius server we want to use for the primary radius server for these AP's. This radius server has been added to the WLC. I have setup a FlexConnect Group, designated the the primary and secondary servers, and then added the AP's to the group. It does not look like radius requests are being sent to the local controller.
For this to work, do we have to check the box under the wlan for FlexConnect Local Auth? Currently, we only have FlexConnect local switching selected.
I need to integrate Cisco ISE and WLC5508 with FlexConnect (local switching) using EAP-TLS security for wireless clients across multiple floors (dynamic VLAN assignments based on floor level). The AP model used is 3602.
- What RADIUS Attribute can be used for dynamic VLAN assignments based on floor level? Is there an option where I can group all LWAPs in same floor for getting certain VLAN from ISE?
- I intend to use WLC software version 7.2 since 7.3 is latest version. Has someone use WLC software version 7.3 without any major bugs/issues pertaining to FlexConnect and EAP-TLS?
- I read some documents saying L3 roaminig is where the associated WLC has changed. However if user move to different subnet but still associated to the same WLC, would this be consider as L3 roaming too?
We have a 5508WLC recently updated to 7.2.110.0 since we are using CAP3602I-N-K9, this AP is intended to work as a H-REAP device and eventhough it is registering to the controller I can't get to see the WLANS on the list to map it to the local VLANS
I have verified and the WLAN is configured for local switching also have followed the steps listed here:URL
Still Can't see the WLANs under the Flexconnect tab on the AP?
Phones will not link to my wireless modem?
View 1 Replies View RelatedI am working on a new install where the customer is using local RADIUS servers at each of their many campuses (for local dynamic VLAN assignment), while using a single set of controllers at the core of their network. For the record, we have set up a pair of 5508s (v 7.2.103.0) in their central data center with 3602i APs around the various campuses. We are using FlexConnect groups to locally authenticate and switch the users.
Right now, the config is working great as far as authentication and local switching goes. The problem we are experiencing is that none of the authenticated usernames are being passed back to the controller (and ultimately NCS). This makes the tracking and troubleshooting of users difficult. Is there something I am missing here? I can't seem to find any fixes relevant to this issue in the 7.2.110.0 release notes.
One of my 7921 phones disconnect ten time an hour and during conversations. Sometimes, people who call on this phone are redirected to the answer message.This phone is connected through WIFI network and Cisco Callmanager 4.2 manage all phones (we have about 80 phones on the network). I thought it was a problem with the phone but I exchange with another one and it's exactely the same problem. The problem is just for a line in particular. All the 7921g phones in my company are configured from mac address in the call manager. This problem occured after a storm but I'm not really sure that it's related to.
View 2 Replies View RelatedAndroid users can connect to our hospital guest wireless but will not have connectivity. Our wireless infrastructure is WISM based with 2 controllers on 6509 platform. We have a mixed environment of 1231, 1252 & 3502 series APs.
Had issue connecting just Android devices? All other devices connect fine.