I have a customer that have trouble with the update of the position of a client. Even if the clients walks across the whole building, the client will stay at the same place for several minutes. Is there any way to tune the refresh rate? When I push the load button in the map, the clients position will refresh, or it did when I was on the site, now they just test with an application.
The setup:
WiSM 7.0.220
WCS 7.0.220
MSE 7.0.220
They use the API for MSE to get the location information to the external application, and that will show the information on a cisco 7925 IP phone.know a way to increasing the refresh rate?
I just got an EA3500 and I guess I don't understand what "Refresh" does when viewing the DHCP client table under the "Status", "Local Network" tab of the web interface, either that or it's not working. If I have active wired and wireless clients and I power off the EA3500, wait a few minutes, then power it back on, the table is blank. If I hit "Refresh" I would expect it to re-populate the table with the connected clients. For whatever reason, it doesn't. I have to physically disconnect and reconnect the E-net cable, or power cycle the wireless client to get them to reappear in the table. Is something wrong with the router or its s/w
i have configured some 1142n's, everything works in terms of .n but the reported client connection on the AP does match the published MCS definitions.eg so what does "Current Rate (Mb/sec) m6-4" actually mean in terms of MCS connection
I would like to be able to allow a specific client to only associate at 6mbit/s -is this possible using the wlc controller 5508? Another option would be to limit a whole w lan ssid to 6mbit/s but i can't find a way to do that either.
Other w lan ssid's on the same access points/controller need full data rates, so i guess i can't use the RF-profiling for this.
I'm running PI 1.2.1.012 and I'm having issues populating client information. Most of my switches are 2960 series. Specifically I get a lot of MAC Address "Unknown" and nothing in the IP address field. I probably get about 25% of the correct MAC address and 10% of the IP addresses. I also run CiscoWorks Prime LMS 4.3.2. and the user tracking information is about 98% correct pertaining to MAC address and IP address. My other network management tools also are very accurate.
Which Intel network cards runs well with E4200 (latest FW)? I mean good connection and transfers rate. I have two clients with the same cards (Intel 4965agn, latest driver) and I got transfer rates at 144 Mbps with both radios working (2.4 and 5GHZ on the E4200). When I try to use 5Ghz only it drops to 54 Mbps and for 2.4Ghz it drops for 130 Mbps. Could I reach better transfers rate with a Intel 4965agn card (300 or 450 Mbps)?
have configured Cisco IPPhone 7925G with EAP-TLS setting. (With manufacture installed and Userinstalled certificate). My issue is while roaming from 1 AccessPoint to another AccessPoint the call getting droped. I need to restart the IPPhone to reauthentiate again. In ACS am agging the authentication time-out error. (I had changed the time out value for EAP-TLS to 20 in WLC as per recommendation.)
If am using static web key there is no issue in roaming.
What is the reommended setting inorder for the EAP-TLS to work properly.
I am working on a wlc 5508 in a lab environment doing snmp reporting & i was wondering if there is anyway to after the timing on how quick the snmp traps appear on the trap log page? I have looked through the gui but cant seem to find anything, so not too sure if there is a cli command, the traps come in very quickly on the nms way before they appear on the trap log page.
We have a problem when I call bettween two 7925 in same SSID, VLAN voice. They cannot hear each other. The SSID and LAPs are in Flexconnet. From desk phones there are no problem and betwen one deskphone and one wireless phone there no problem too.
I've been having a problem with my wireless network connection. Whenever I try and hit the Repair function,it will get stuck on Renewing your IP address for a moment, then change to: Windows could not finishing repairing the problem because the following action cannot be completed: Connecting to the wireless network. I have internet connection on this same computer.Another point to make is that when I click Repair and navigate to the Network Connections window, then hit F5 ( refresh the window ), the wireless connection will quickly refresh and connect normally without error.I won't have to open the Network Connections page and hit F5 anytime I need to repair the connection? Also, as of right now, it's still "Acquiring network address" even though I'm connecting and typing this message.
recently we have deployed a Two APs in branch office warehouse and I have one wifi phone 7925 used over there. the problem is every time when phone roaming from one AP to another, 2 or 3 packets dropped, following is result of the 'debug client ':
--More or (q)uit current module or <ctrl-z> to abort*apfMsConnTask_7: Jun 27 09:52:25.496: 88:43:e1:4f:ab:39 Association received from mobile on AP a0:cf:5b:c3:a8:90*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 10.107.38.121 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying site-specific IPv6 override for station 88:43:e1:4f:ab:39 - vapId 14, site 'AKL-AP-GP', interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying IPv6 Interface Policy for station 88:43:e1:4f:ab:39 - vlan 38, interface id 0, interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39
How to get the FCC ID from a 7925 phone. We have one on order for an upcoming VoFi site survey but I wanted to take a look at the maximum output power by channel so I can begin cell/channel planning.
I have 802.1x configured on a 3550 switch with ACS 5.1 acting as the AAA policy server.
My problem is this. When my computer boots up, ACS authenticates the machine to AD slapping me in a guest VLAN with limited access to the network. Once I login though, I reauthenticate to AD via ACS which then puts me into an employee VLAN but my IP address doesn't refresh automatically. I have to run ipconfig /renew to get my IP in the correct VLAN or write a logon script that does the same thing everytime I log in.
Is there anyway for this to be done automatically outside of writing a logon script?
I have an issue with the 7925 phones. We have a Cisco Call Manager with a couple of access points and a wireless lan controller. But we have at some points some sort of hole in the sound. He doesn't loose it's connection because i don't hear the beep when he's out of range. And according to the phone he still has a connection with the access point. But there is no sound anymore. And if i walk a couple of meters further i got sound again. If i walk back i somehow get in the same hole and loose the sound. Further back in i got sound back.
I know when it comes to WiFi that there can be some sort of blind spot but there isn't. He still has it's connection with the AP. Is there a value regarding de RSSI value that he needs to have to get a normal speech?
I'm currently in the process of the setting up a new wireless network and I want to test out our 7925 phones on it. When I try uploading the certificate to the phone it fails and I find the following error in the trace logs
[code]...
I created this certificate using using Windows Server 2003 and it is 2048 bits. This certificate works fine with my laptop but I'm unable to upload it to the phone. The app load currently on the phone is CP7925-MFG-D.8.LOADS. Are there any specific guidelines out there when creating a certificate for a Cisco 7925 phone?
After some time LMS stops to refresh network topology (not changing colors for devices which lost/found). However, if I restart topology services devices are refreshed.
Checked the processes. Everything is fine but there is a process named "1018". But I did not found any job with this number.
Using Sha1 for Cisco 7925g and sha256 for data. Two separate CA's, one EnTrust (SHA1) the other Local Wondows CA (SHA256); ISE can only use one at a time to process a particular protocol (ie..EAP-TLS, HTTP, etc...) As a result we have to have a separate PSN just for Wireless and Wired VoIP (which can only hold SHA1 RSA1024).
The various setup pages of the RV220W router have an auto-refresh interval. I can change the interval from the default 10 seconds to 60 seconds maximum.I cannot change the Dashboard to different than 10 seconds.Every time I try to work with these pages, they black out and refresh, stopping my work.How do I change the Dashboard auto refresh interval to 60 seconds?Can I change all the auto refresh intervals to 10 minutes?
when using SNMP on our cisco 3845 the traffic logs are set to refresh every 1 second but the data seems to come in 5 sec burst.so does not some a real time status of the interface throughput.
I have a problem with MSE tracking client in my network.What we have:PI 1.3 with evaluation license (temporary)MSE 7.4.100 with 3k device licenses (hardware appliance 3355)WLC 5508 7.4.100.For now MSE is reacheble from PI and WLC, all setings are synchronized, NMSP status is active, mse assigned for maps and synchronized, on map we have 3 APs, but in Contex Aware tab we didnt see any tracking devices, all counts 0.
I have 2 Cisco WLC 4400's connected to a WCS. I want to use this Location Tracking feature within the WLC 4400s so that i can track movement of particular network devices throughout my facility. I cannot find anything on how to set this up on the internet. I found a PDF explaining the 4 different ways you can track objects but nothing more.
Is this service still supported in the newest versions?
I downloaded and upgraded my router to the 3.0.03 firmware. Downloaded the bin file, saved the config, upgraded firmware, reset router and restored configuration. Everything went ok but router still shows 3.0.02 firmware. ?I have a camera system on the network routed through two opened ports on the router. Everything works fine.The camera system does not store any logs relative to remote access. I would like to log any incoming traffic on the camera open ports. Is there a way to do this on this router?
I have setup an FTP site using the USB attached storage on my router. I would like to track when the site is accessed from the Internet. The logs don't show anything because the site is on the other side of the router. Is there a way to track activity to / from the site?
I have 4 - WAP 321's in an office all connected to a POE gigabit switch. Each WAP shows connected at 1GB but when I am sitting within a couple feet of the WAP and attempt to transfer a 972MB file it takes around 9 minutes to complete. speeding this up? All 4 AP's are setup as a cluster as well.
We have a client that has a large number of AIR-AP1252AG-N-K9 installed in the network with power injectors. We have seen a about 48% failure rate of AP's failing with all 3 red lights on the unit. Once I get the AP in the lab I'm unable to get any response from the console, therefore unable to troubleshoot.
I've spent parts of the past five days buying and exchanging several WAP4410N units because I was not able to achieve anything close to a 300Mbps data rate. I also tried various wireless-n network cards which were known to be configured correctly for 300Mbps speeds with no luck.
The highest speed I was able to achieve was 130Mbps, which is an indication that channel bonding is not in effect.
Then I came across another post in the forums:
WAP4410N does not exceed 130Mbps in N mode at close range.
where the OP mentions recently upgrading to firmware 2.0.4.2, though not treating that as the cause of his problems.
On a lark, I tried downgrading to both firmware 2.0.2.1 and firmware 2.0.3.3, and to my surprise, I was able to achieve the full 300Mbps data rate with both firmware versions.
When I reverted back to 2.0.4.2, I was not able to achieve the full 300Mbps data rate.
So, right now, I downgraded to firmware 2.0.3.3 so I can get the higher data rate, though there are other quirks to deal with.
Furthermore, when I do a web search of reviews, I can see that the inability to achieve the 300Mbps data rate is a huge source of complaints.
I have a client devices constantly sending data (~ 13 kb per second) to a server through a Cisco AP1241AG (802.11g).I use Iperf to test throughput, but I am having a difficult time determining what an acceptable throughput rate would be.I know in "theory" the best throughput rate I could get is 54 Mbps, but since my client devices only send 13 kbps is 1 Mbps more than enough? or is 13 kbps the low limit for my throughput test?
I have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
I have had a DIR-655 for years, and this is a treat - channeling everything from IPTV, to a fast fiber connection, transfers - no sweats.
Then I had to setup a router for a friend, and recommended the DIR-615.
Setup the router, and max it would connect with was 150mb - I changed the settings accordingly: auto channel scan channel width: auto 20/40mhz
So this "opened" up the 300mb speed - however only for 5 mins, then it falls down to 150mb.
My laptop (lenovo) connects to the dir-655 just fine at full speed, and this is also the machine I used for testing the dir-615.
It's ax Hx firmware, FW: 8.04
What I can conclude by using inssider, and xirrus wifi inspector is that it generates 2 channels - and then after 5mins of connectivity looses a channel, and then the speed drops.
I got a new router from the dealer, same issue. Then a friend of mine lent me an ancient dir-615, and interestingly enough this had the same configuration option of "Transmission rate" in the wireless settings page! Just like the dir-655. and also connects at 300mb...
I have a home network running on a Linksys WAG320n and i have attached to it a WD MyBookLive (w Gigabit Ethernet). I am connected on the network via my Dell with a Intel(R) WiFi Link 5300 AGN. I am not able though to connect on N range. I have installed the latest drivers from Intel but nothing changed. When i try to copy a file from my computer to the WD Network drive the transfer rates are very slow. I get Max 2MB/s - 3MB/s while if i connect my computer with a wire the speed goes up by 3-4 times more.
How can I see network rate of other computers connected to my WRT54GL wireless router?I have admin password and I want to see how much bytes/sec received and sent from all the computers connected to the router.
