Cisco Wireless :: WLC 5508 7.4.100 - Getting MSE Tracking Devices Through Network?
Apr 5, 2013
I have a problem with MSE tracking client in my network.What we have:PI 1.3 with evaluation license (temporary)MSE 7.4.100 with 3k device licenses (hardware appliance 3355)WLC 5508 7.4.100.For now MSE is reacheble from PI and WLC, all setings are synchronized, NMSP status is active, mse assigned for maps and synchronized, on map we have 3 APs, but in Contex Aware tab we didnt see any tracking devices, all counts 0.
View 11 Replies
ADVERTISEMENT
Jan 29, 2013
I am setting up a new Guest network with a captive portal and it seems to all work fine except when Apple devices go to sleep. When they come back on it isn't just a case of logging in again as it just indicates to the client that it is still connected and won't present the login page again. The Controller will show the client as auth required. So far the quickest way has been for me to delete the network on iPads and re-enter my settings or create a new profile on a Macbook and join again. I have also had some success when doing a manual DHCP refresh on my Macbook which sometimes seems to kick the Controller into action so it presents the login page to the client again. Whether it is related to the timers on the Controller (5508 running code 7.0.235.3) or - as I just read in another post by Leo - the 20 minute timeout that all Apple devices have built in to conserve battery life
View 3 Replies
View Related
Jun 14, 2012
I'm seeing a problem with Apple IOS devices connecting from one SSID and then connecting immediately to another. I've tried to replicate this fault with non Apple IOS devices, but I'm unable.
Environment:
Single 5508 WLC running 7.2.110.0 AIR-LAP1142N-A-K9 AP's
WLC is in clients head office, MPLS to their branch sites. AP's are in Flex Connect mode, with AP and Flex Connect groups for the AP's at the branch. 3 x SSIDs; Corporate (802.1X), Guest (Web-Auth) & Non-Corp (PSK).
Scenario:
Client is connected to the Corporate SSID with his iPad (new model, running iOS 5.1.1). No problem with access, he is able to roam throughout the building with good SNR/RSSI. He wants to test the other SSID's, he attempts to connect directly to the Guest or Non-Corp and gets an error message on the client saying 'Unable to Connect' or 'Unable to Join'. Debugs on the WLC for the client shows no connection attempt, no errors. I can see the client disconnect from the Corporate SSID, but nothing for the Guest or Non-Corp SSID.
If the client then disconnects and forgets the Corporate SSID from the wireless profiles on their i Pad, waits 20-30 seconds (I can see the client disconnect cleanly from the WLC) and then attempts to connect to the Guest or Non-Corp SSID's - he doesn't have a problem. He immediately associates, and is able to connect. If he then tries to connect directly to another SSID, while still associated to another from the same WLC/AP – he gets the error again. Forget/wait 20-30 seconds, attempt to connect – no problem. We've tested with several i Phones (4 & 4S), i Pads (2 & new model) - all running the same Apple IOS (5.1.1).
I unfortunately can't do much troubleshooting with TAC on this as the client is no longer onsite, and I don't have a 5508 in our lab that I can currently test with. I've tried playing with beacon intervals, etc to no avail.
View 3 Replies
View Related
Jul 26, 2012
setup a WEP SSID on my 5508 controllers. THat being said, I have multiple sites with extremely old scan guns that only do 104bit wep. I plan on locally switching this SSID and using static WEP 104bit key with MAC authentication, and then ACLing to limit my inherent security issues/exposure once someone compromises my WEP key. [code]
View 4 Replies
View Related
Aug 25, 2012
We have integrated WLC 5508 to cisco ise 3315 with ios 1.1.1 and using Guest Sponsor portal for wireless guest users.Where we have created open ssid in wlc and redirect web login portal in wlc for guest users. We have enable all respective node in policy service for profiling and also configure snmp in wlc as well as in ise.
When guest user is connected to open ssid its get redirected to web login page of ise portal and when it gets login we are only able to see the username which guest user login but not the end device in monitoring log.
Wireless End devices are not able to get profiled can any one tell me what configuration I need to do on ise or wlc side to profiled end guest wireless device like android,iphone and laptops
View 7 Replies
View Related
Jun 12, 2013
I have 2 x 5508 WLCs in place with around 50 APs split between the 2.
As there is currently a low uptake of using wireless devices all of which we own I have up until now been using WPA2 and MAC filtering to control access to the network.
This all needs to change as we are about to embark on the B.Y.O.x revolution. This means being able to support a wide range of OSes from Windows to Android. This in itself presents a whole series of issues but right now I'm trying to explore how much of the burden the WLCs can take.
For instance I was thinking about setting up web auth on the controllers that would authenticate against an external RADIUS server - this seems fairly straight forward.
If this was to be a bog standard windows network I could set up a Microsoft NPS server that could control and define policies to mobile devices, but as this is going to be a mixed environment that's not a solution I can use.
What other features do the controllers provide that would be useful in my situation - can you for instance automatically direct data to a specific vlan based on authentication information?
View 1 Replies
View Related
Apr 25, 2012
Every other day and sometimes everyday I have an issue where my network slows down in one area at around the same time of day 12:00pm. I am using Solarwinds and I don't see anything significant showing up.
View 2 Replies
View Related
Oct 15, 2012
Is there any shut down proceedure for cisco devices in data center cisco router,switches,firewalls ASA-5580-20,ace-4710 and IPS-4260 devices.
View 4 Replies
View Related
Feb 12, 2011
I have been testing WiFi devices such as the iPhones and iPads connectivity with the following setup:
1. 3502i AP
2. WLC 5508 SW 7.0.98
3. NGS
The i-devices have iOS v4.2
My goal is to have the guest user i-devices maintain the credentials (username and password) when they login again to the wireless network. Like if the device sleep, I think definitely they would loose those IP address issued by the DHCP. Once the guest user uses them again and connect them to the wireless network the user would not need to type-in those credentials on the Web Authentication page directed by the WLC.
The credentials are issued by the sponsor who created them on the NGS. It seems that there are WiFi problems with these i-devices. But somehow, I'm looking for a solution that would automated the logins like a checkbox if you want to be kept signed in, on Yahoo or Stay signed in for GMail.
View 6 Replies
View Related
Jan 24, 2013
My company thus cuts off my subscription before the month ends.My family and I use a total of 8 devices on our home wireless network; 3 laptops, 4 iPads, and a Galaxy phone.My router/modem home page shows me the total amount used by all users.. I use a huawei LTE B593 router.
View 2 Replies
View Related
Aug 2, 2012
I'm facing a problem related to devices authenticating to our wireless network. Below are how it is setup:WLC 4404 pass authentication to ACS 5.3 (PEAP + MsChapV2) then to AD server.Client can get stock in this status and it keeps repeating from 1 to 20.
View 4 Replies
View Related
Jan 17, 2011
I recently added several devices to my wireless-g network: Xbox 360, an HTC Smart phone, and an old laptop my buddy gave me (in addition to the 2 desktops that were already on the network). Since doing this, I've had occasional buffering problems when streaming music or video, even when I'm only using 1 of the devices. I suspect that the Xbox (or maybe phone) is downloading updates in the background, even when it's turned off, and that is consuming bandwidth. Is there any way I can see a list of devices that are connected to the network and maybe even the amount of data being transmitted to/from each so I can find the culprit. when I play online, it says that my NAT settings are not open and that this makes it take longer to connect to other players. What are the risks involved in loosening the NAT restrictions?
View 1 Replies
View Related
Sep 11, 2012
I'm having constant lag spikes. I use DPC Latency checker [URL]On both my desktop (using PCI wifi card) and my laptop I have lag spikes. This is a screenshot of the spikes [URL]. Although it says its my hardware problems, I doubt its true, as it happens on both devices.
View 1 Replies
View Related
Sep 30, 2012
My laptop with Windows 7 64-bit is not being able to connect to the home wireless network. But other devises like iPad and iPhone and Mac laptop can connect to the same wireless network. However I can connect to the network if I connect my laptop directly to the wireless router using a network cable.I have tried upgrading the firmware in my wireless router but no luck. THis laptop had no problem before connecting to the same wireless network. But since I came back from the back home couple of days back I am seeing this problem. But my laptop can still connect to my my-fi devise wireless network. I have tried running the netsock commands listed in a similar thread in this forum but no luck.netsh winsock reset catalog netsh int ipv4 reset reset.log netsh int ipv6 reset reset.log
View 5 Replies
View Related
Sep 6, 2011
I have 2 Cisco WLC 4400's connected to a WCS. I want to use this Location Tracking feature within the WLC 4400s so that i can track movement of particular network devices throughout my facility. I cannot find anything on how to set this up on the internet. I found a PDF explaining the 4 different ways you can track objects but nothing more.
Is this service still supported in the newest versions?
View 8 Replies
View Related
May 25, 2013
Have a WAP321 connected to a Cisco SG200-08P then connected to a Cisco 2901. The main wireless on vLAN 1 works fine. However, the Guest on vLAN 4 (Choose vLAN 4 as per the included docs so guests will be unable to see the production network) will not give an IP to any wireless device. Looking for documentation on getting the Guest radio working. The included documention for these 3 devices do not address how to get the Guest radio to work.Does vLAN 4 need setup on the 2901? Have just 1 internal port on the 2901.
View 14 Replies
View Related
Jul 25, 2012
I have recently deployed a wireless network using a WLC 2504 with 21 Light APs. All seems fine except that Apple Devices drop their connections every 15 minutes or so. A couple of minutes later they can reconnect but obviously something is wrong.
View 2 Replies
View Related
May 27, 2013
Recently, I have configured a small Wireless Network with Cisco 2500 WLC (25 AP License) running version 7.3.101.0 ,Total 15 APs were installed and associated with the Controller successfully.I have configured WLAN with WPA2-PSK.
I came across a strage issue, where all Android devices can't access Internet via Wireless.When I checked the Controller log, the Android devices (Phones, Tablets) are successfully authenticated and associated to the Wireless Network (They got the IP Address from the DHCP Server configured on the Switch) but they can't access internet.
There is no issue with Apple devices (IPhones, IPADs) and Wireless Laptops. Even the Apple devices and laptops getting IP Assigned from the Same DHCP pool configured on the Switch.
Any issue connecting just Android devices? All other devices connect fine.
Is there any limitation/configuration on the WLC which restricts the Internet Access only to the Android devices?
View 6 Replies
View Related
Aug 15, 2011
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies
View Related
Jun 16, 2012
I recently purchased a newer Netgear wireless router ($50 or so) to replace an old one because I was constantly having to reset it to successfully get an internet connection on my computer, my phone, and our wireless printer. Now, the computer and phone have no problems picking up the network, but I always have to reset the router to get the printer to pick it up.
View 9 Replies
View Related
Jul 15, 2012
Just upgraded my system. I am using D-Link 615 as access point hardwired LAN to LAN to ActiveTec MI424WR N capable Verizon Fios Wireless Modem/Router. The Fios Router is set up with WPA2 security. Intend on having three 615s as Access Points off of ActiveTec. Have a number of wireless devices accessing the network. Have followed instructions from manual to use 615 as Access Point, disabling UPnP and the DNCP Server function on the 615. My ActiveTec IP address is 192.168.1.1 and I changed the 615 to 192.168.1.50. I can type this IP address in my browser and get to the 615 set-up.
I have tried a couple different options in naming the SSID on the 615 set-up. If I name the SSID on the 615 the same as the ActiveTec router, when I go to Connect to a wireless signal where there is overlap, there are two signals that one can connect to, named the same SSID, the Fios is WPA2 secured and the 615 is not. Shouldn't these all be on one SSID? It seems that I have two different networks (different SSIDs) instead of one (rather than the 615 simply serving as an extension of the Fios router as a wired remote access point) with different security protocols (WPA2 and None). The SSID name almost seems meaningless. If I name the 615 SSID the same as the Fios router SSID or something different, I still have the option of selecting one SSID that is secure and one that isn't. If I try to connect to the SSID name associated with the 615 I can get on without providing a password.How do I make it so that one can walk around and go from one area to the next and seamlessly move to the best signal? I did read to select different sets of channels for each access point.
View 3 Replies
View Related
Mar 14, 2012
I have a customer that have trouble with the update of the position of a client. Even if the clients walks across the whole building, the client will stay at the same place for several minutes. Is there any way to tune the refresh rate? When I push the load button in the map, the clients position will refresh, or it did when I was on the site, now they just test with an application.
The setup:
WiSM 7.0.220
WCS 7.0.220
MSE 7.0.220
They use the API for MSE to get the location information to the external application, and that will show the information on a cisco 7925 IP phone.know a way to increasing the refresh rate?
View 3 Replies
View Related
Feb 18, 2012
We connected 4 wireless access points (AP541N-E-K9) to an SG300-10P switch.We want to be sure that no wireless clients can alter settings to the network by connecting to any of the networking devices. We also want that no wireless devices (except a few) can connect to computers that are on the wired network. I'm new to configuring networking devices so how to set up the switch for this.We already added all the MAC-adresses of all the wireless devices (that are allowed to use the wireless network) to the access points.
View 3 Replies
View Related
Jul 30, 2011
I downloaded and upgraded my router to the 3.0.03 firmware. Downloaded the bin file, saved the config, upgraded firmware, reset router and restored configuration. Everything went ok but router still shows 3.0.02 firmware. ?I have a camera system on the network routed through two opened ports on the router. Everything works fine.The camera system does not store any logs relative to remote access. I would like to log any incoming traffic on the camera open ports. Is there a way to do this on this router?
View 2 Replies
View Related
Feb 22, 2013
I have noticed from time to time I get many (15-20) "network devices" in the Device List with no MAC address. I notice this mainly when managing Parental Controls. I go and clean up the Device List and days later they reappear. Another interesting thing is that the computer I am writing this with (through the router) does not show up in the Device List and I have an IP address from the router. I have the latest firmware 1.1.28.146856. Does anyone else see this on their EA6500?
View 2 Replies
View Related
Nov 12, 2010
I have 3 computers in total: 2 desktops and 1 laptop.
1. My primary PC is connected physically to my router.
2. My (downstairs) laptop is connected to the wireless.
3. My other PC connects to the wireless network via USB wireless adapter.
I was having issues getting #3 connected to the wireless network. I used the Wi-Fi Protected Setup™ PIN number provided to me by the Linksys Wireless Manager to no avail. The E3000 router and #3 could never find each other.After calling support, it turns out that more often than not, "other" wirless management software (in my case Linksys Wireless Manager that came with the USB device) was interfering with my Windows XP Wireless Manager.Rule of thumb: Always let your native operating system manage the wirless networks that are available to it. It does a far better job and is 10x more reliable than software provided by 3rd party vendors.Specific to my case: Windows XP, I had to enable the Windows Wireless Manager and uninstall the Linksys Wireless Manager Software. Here it is...Enabling Windows Wireless Manager These directions are for Windows XP:
1) From the Windows Start menu, click Control Panel.
2) Click Network and Internet Connections.
3) Click Network Connections.
4) Right-click the icon for your "wireless network connection", then click Properties.
5) At the top of the window, click the Wireless Networks tab.
If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs, you are not on/in the wireless network connection settings:a) click cancelb) Right-click the icon for your wireless connection and choose "Enable". c) return to step 4 6) Check the checkbox next to "Use Windows to configure my wireless network settings".
These directions are for Windows Vista:
1) Go to the Windows start menu and then the control panel.
2) Open Network and Sharing Center.
3) Click Manage Network Connections (from the left side menu).
4) Right click on the network adapter 'Wireless Network Connection' and choose "Properties" and click "Continue".
5) At the top of the window, click the "Wireless Networks" tab.
If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs: a) click cancel b) Right-click the icon for your wireless connection and choose "Enable". c) Return to step 4
6) Check the checkbox next to "Use Windows to configure my wireless network settings".
View 7 Replies
View Related
Sep 15, 2011
I was requested to connect 2 WRT54G devices in our network with same ip range.
View 2 Replies
View Related
May 4, 2012
How do I view (from my desktop) what devices (iPods/iPhones) are connected to my wireless network? I have several questions re: control over my network, but I think this question is the first thing I need to know.
View 1 Replies
View Related
Aug 18, 2012
I need to connect a pc desktop and A linksys PAP-2T voip adapter to an existing wireless network(home network).
View 7 Replies
View Related
Dec 31, 2012
The network is constantly disconnecting from my devices and wont let me reconnect...I reset the network completely back to factory settings and started from there. Some of my devices didnt want to connect at all after the complete reset.These are the settings that I have changed: SSID has been changed,wifi security(wpa2 personal,AES) ,channel(width=20, channel=auto) ,DNS server(changed to Norton DNS: 198.153.192.40 & 198.153.194.40) & router management logon password & firmware upgrade to 3.0.03...
Router:Linksys WRT160N V1
Firmware:3.0.03
View 9 Replies
View Related
Jan 3, 2012
I have a WRT610N which does not allow me to connect any new devices to the wireless network. This is a recent problem as I have been able to connect new devices before. Devices on the wireless network, those that have been on the network, are able to disconnect and reconnect. Just new devices are excluded. Have gone through the admin screens to see if something is amiss but can not find anything.
View 5 Replies
View Related
Nov 6, 2011
For a while now, my wireless network at home has been very unreliable. I posted on these forums before, asking for assistance to fix crashes that seemed to be random. I was largely unsuccessful, and the problem continued. However, as I continued to experiment with different methods to keep my network up and running, I noticed that as long as I had at least one device connected to the network around-the-clock it never crashed. This was easy enough, as I own an iPod touch and a dock (I would leave it sitting it the dock unlocked all the time). But it's annoying to never be able to leave the house with it, and I'm ready to finally get a solution to the problem once and for all. I would prefer not getting a new router, but if worse comes to worse I will.
To sum it up:
-Works perfectly (when up) at full speed, never crashes unless there are no devices connected to it.
-When it does crash, it is very difficult to 'coax' it back into working again; it's been down for weeks at a time before.
-For some strange reason (and maybe this is a clue), newer game systems such as a Nintendo DSi or PS3 can make it start working again. I, of course, own neither of these.
-I'm using a WRT160N V3, latest firmware as far as i know.
View 9 Replies
View Related
Jul 3, 2011
I cant see in my network the devices connected to SE2500 just the SE2500 itself. The internet access of the devices connected to SE2500 is working correctly. Is this a problem?
View 3 Replies
View Related
