Linksys Wireless Router :: WRT160N V3 - Network Crashes When No Devices Are Connected?
Nov 6, 2011
For a while now, my wireless network at home has been very unreliable. I posted on these forums before, asking for assistance to fix crashes that seemed to be random. I was largely unsuccessful, and the problem continued. However, as I continued to experiment with different methods to keep my network up and running, I noticed that as long as I had at least one device connected to the network around-the-clock it never crashed. This was easy enough, as I own an iPod touch and a dock (I would leave it sitting it the dock unlocked all the time). But it's annoying to never be able to leave the house with it, and I'm ready to finally get a solution to the problem once and for all. I would prefer not getting a new router, but if worse comes to worse I will.
To sum it up:
-Works perfectly (when up) at full speed, never crashes unless there are no devices connected to it.
-When it does crash, it is very difficult to 'coax' it back into working again; it's been down for weeks at a time before.
-For some strange reason (and maybe this is a clue), newer game systems such as a Nintendo DSi or PS3 can make it start working again. I, of course, own neither of these.
-I'm using a WRT160N V3, latest firmware as far as i know.
View 9 Replies
ADVERTISEMENT
Dec 31, 2012
The network is constantly disconnecting from my devices and wont let me reconnect...I reset the network completely back to factory settings and started from there. Some of my devices didnt want to connect at all after the complete reset.These are the settings that I have changed: SSID has been changed,wifi security(wpa2 personal,AES) ,channel(width=20, channel=auto) ,DNS server(changed to Norton DNS: 198.153.192.40 & 198.153.194.40) & router management logon password & firmware upgrade to 3.0.03...
Router:Linksys WRT160N V1
Firmware:3.0.03
View 9 Replies
View Related
Jul 3, 2011
I cant see in my network the devices connected to SE2500 just the SE2500 itself. The internet access of the devices connected to SE2500 is working correctly. Is this a problem?
View 3 Replies
View Related
Aug 14, 2011
I've been using a WRT160N for a couple of years now with no problems with any of my devices. I have a couple of certain devices (a DS and a PSP mainly) that utilize 802.11b and have been working perfectly up until now.
All of a sudden it seems like the router has decided all by itself to no longer allow 802.11b devices to connect to it, despite it being configured in mixed mode. (b/g/N) I've tried tinkering around with it, switching between Mixed and BG-Mixed, changing the channel to something more common and restarting the router, but I can't connect at all on these devices.Model: Cisco Linksys WRT160N v3.Firmware version: 3.0.03.
View 1 Replies
View Related
Oct 9, 2012
As of last night my router has been producing slow connectivity when multiple users are connected to it, but it's perfectly fine when only one user is connected. I am on a laptop myself, but we also have a second laptop and a desktop where the modem and router are set up. I have upgraded the firmware so that is up to date. We have Comcast Fiber Optics so my internet speed is normally quite fast even when all of my computers are connected.
I am using DHCP Configuration. My Channel Width is set to 20 MHz and I am using Channel 11. The Security Mode is set to WPA Personal. I had it on WPA2 Personal but I read that changing to WPA Personal might work and so far it doesn't seem to have done anything. I set the Beacon Interval to 50, Fragmentation Threshold to 2304, and RTS Threshold to 2304. Everything else is set to the default factory configuration.
Just today I received a notice that said "Windows has detected an IP Address Conflict", but ever since I reinstalled the Firmware it hasn't come back. I've rebooted both my laptop and the desktop to confirm it hasn't come back as well. I've tried everything that I could think of including reconfiguring my router and restarting my modem as well.
View 6 Replies
View Related
May 1, 2011
I was wondering if there was any way with a typical home router (for instance I have a Linksys WRT160N) to create a wireless network which is essentially sandboxed from the rest of my network. Basically I want devices on this network to be able to access the Internet only, but not any of the other computers on the network.
View 2 Replies
View Related
Jul 11, 2011
I've used Netgear & other routers for years; I was able to see the devices connected over ethernet & wifi through the router configuration utility. Cisco's interface looks poor; there is no way to see the connected devices.Many of the devices I have have a 5 Ghz radio and some don't so i need to see at what speeds they are connecting at.Or does Cisco not provide this utility? I am surprised that a high-end product from Cisco does not have this function.
View 9 Replies
View Related
May 13, 2012
How can I tell what devices are connected to my WRT54G?
View 4 Replies
View Related
Feb 13, 2012
So i just set up the Linksys E2500 and it shoes 8 devices connected to my router. How I can see what devices are connected?
View 1 Replies
View Related
Nov 16, 2011
I've got the E3000 set up and working. What I'd like to do now is monitor all the devices' connectivity to it. The bandwidth it consumes and stuff. Is there a way to do that on my router?
View 6 Replies
View Related
Oct 18, 2010
How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies
View Related
Mar 6, 2013
I have an EA 4500. Tonight I was trying to see what devices were connected. The window shows 0 devices connected, although about 20 devices are connected and working. When I click on "Devices Connected", I get the spinning wheel, and after multiple attempts by the application to list devices, I receive a message that the application does not work. I have the latest firmware installed. This is a recent issue. I have not made any changes to network configuration, nor to any of the devices that all have internet access. I will note that I did not set up a separate SSID for each band. But that did not seem to be an issue in previous months. I also cannot access the router ui from my windows 7 desktop. I can access the abbreviated ui through my Android phone. I tried connecting through smart wi-fi and by ip of the router. I just get the endless spinning circle of dots. I am running Windows 7 all up to date. All drivers are up to date.
View 7 Replies
View Related
Dec 8, 2012
My EA6500 are not displaying all the connected network devices on in the GUI. How do i force this? Is it a bug? How can I make sure all my devices are showing in the GUI?
View 5 Replies
View Related
Jun 17, 2012
I am trying to find out what devices are connected to my router. I have had some illegal downloading from my IP address but it has not been done from my computer. It is showing in Cisco Connect that I have 15 devices connected, I should have no more than 6 devices connected so trying to figure out who is connected on my computer.
View 9 Replies
View Related
Nov 6, 2012
My EA4500 with the latest firmware will only display nine connected devices at a time. It also seems to randomly shuffle which devices to show as connected, even though several more than nine are connected and online. Does anyone else's device list limit itself to displaying only nine devices? The Linksys phone apps also display a maximum of nine devices. I like the routers new user interface and understand that it has received a lot of praise, however this is the second bug I've experienced in as many months (the first being a failure of the device list to update once devices are upgraded to Windows 8, requiring a reset to default settings in order to fix).
View 5 Replies
View Related
Apr 21, 2013
My E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies
View Related
Oct 31, 2011
I'm thinking of upgrading from my Linksys WRT54G router to the E4200 and though I've goggled. Also, are there no LEDs on this unit to tell you the status of what's connected?
E3000WRT-54GWVC-80N
View 3 Replies
View Related
Jan 18, 2013
I have a E1200 router and it's pretty good however I've noticed that there are 12 devices connected to my router when infact there should only be 4 devices connected. I would like to see all the devices that are connected and disconnect the ones that don't belong
View 1 Replies
View Related
Aug 11, 2011
I have" a WRT160N but I guess we had a power outage while I was on vacation and now I can't connect to my old network I set up.I see the Linksys internet connection and I can connect but its not the password protected one I set up. When I go to "manage connection" I can see the old "house" connection but can't connect
View 4 Replies
View Related
Dec 27, 2012
I have just purchased a PC Tablet, but cannot add it to my network on my WRT160N Router.All I get is "Authenticating" then "Authenticating problem".
View 1 Replies
View Related
Feb 23, 2008
I am experiencing - loosing network connectivity entirely (between the router and the cable modem) or loosing connection to some clients: 2 wireless laptops - one N and one G, and 4 wired connections. This requires a reboot of the router 2-3 times a day. Never experienced any of these problems with a Linksys WRT54G, a unit that this one replaced. Unless I can resolve it, the WRT54G is going back in, and WRT160N is going back.
View 9 Replies
View Related
Sep 27, 2011
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies
View Related
Jun 24, 2012
This was for a WRT160n v3.0.02 I looked up several suggestions online and decided to update the firmware to v3.0.03 This seemed to only make it worse as I could no longer connect, and when I turned the router off and back on it would allow me in for about a minute and drop me right away.I started tweaking with the settings, and came across some posts here such as this one, started tweaking with the channel settings and everything. Nothing. If anything I somehow made it worse since now instead of dropping repeatedly it wouldn't connect at all except for about a minute after restarting router, then it would drop completely (I would either get the limited access notification or I simply couldn't connect and windows said to unplug the access point. I recalled I had another Linksys router that I wasn't using in storage, a WRT54G2v 1.0.01 so I set that up, no problems... at first. All other devices picked it up right away, but once again, my new laptop decides it's too good for the freaking network and drops it repeatedly telling me there's a problem with the access point.
So at this point I'm thinking it might NOT be my network, but my wireless card or something, I uninstalled and reinstalled, updated drivers, (I use a Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC) I even came across this article and disabled browser service and NETBios (including all other devices on my network). It brought back the network on my laptop for a bit, only to smugly come crashing down again.
View 2 Replies
View Related
Oct 8, 2009
I have a wrt160n router set up at a friends house that i would connect my windows xp laptor to when i would go there. it always worked fine. i recently got a new laptop with vista 64 bit OS. i went to my friends today and connected via wireless for the first time. i expected to get prompted for the security key. instead it asked for the pin #. the pin number was something new i noticed when i replaced an older linksys with the new wrt160n so i had it in my notes. i entered the pin number and connected to the wireless router. but then my friend laptop could not connect and said it couldnt find the network. when i viewed the available networks, i noticed that the original network SSID had been changed to my vista laptop's computer name. i had to physically connect my laptop to the router and reconfigure the settings of the wireless network. then my friend was able to see the available network and automatically connect..
View 6 Replies
View Related
Aug 4, 2011
here is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
View 1 Replies
View Related
Jan 13, 2012
Often my router drops connection to all my devices. Multiple times a day. It's only for a minute or so, but it's annoying. I'm using a Linksys Wireless-N router (WRT160N) with WEP encryption. I'm running two Windows 7 laptops, LG BluRay player, Apple TV, Xbox 360 (Wired) iPhone 4, and a iPad 2. It doesn't matter if I'm browsing the web, watching Netflix, or playing a game, the connection gets lost. As we speak it happened again. I have no clue on what to do. I've reconfigured it multiple times. Firmware has been updated months ago.
View 6 Replies
View Related
Jul 30, 2011
How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 Replies
View Related
Dec 12, 2012
I am unable to connect my Ipad3 to my home network (WRT160N router). It has been working for the last 8 months, and stopped working after I installed Direct TV App on Ipad..It detects the network, but not accepts the PW.... I have multiple wireless devicess connected to my network without any problems..The funny thing is that my neighbor brings his ipad to my house and he is able to connect..My ipad connects to any other network...just not my home network.. I contacted Apple who spend hours with me on the phone and suggested doing a full reset on the ipad, but still did not solve the problem..I called and already paid for linksys support ($62.95) who spend hours with me on the phone, but suggesting: "maybe you need to buy another router"...REALLY!!!! Again, I have 3 Smart TVs, Xbox360, and Wii, that are connected to the network just fine .even my neibor comes with his Ipad3 and connects to my network just fine......and I can connect with my ipad to any other network without any problems... BTW, I have already removed the DirectTV app from the ipad....but I still cannot connect to my network..
View 2 Replies
View Related
Feb 7, 2013
I wounder if there is any way to ping the local deviceses connected to a network hosted by a Cisco 1921 router? I wan't to be able to ping the device(computer name) but currently cant do that.
View 1 Replies
View Related
May 17, 2010
home router is a wrt160n v3 With my iPad I set up the built in IPSec VPN to my office's cisco gateway. I successfully get the VPN logo. With an RDP app, i can access my work network from multiple public locations from my iPad. At home, on my laptop, I start the cisco client then use the windows rdp, presto i'm in my work network. At home on my iPad I can activate the VPN, but I can not connect with rdp. I spoke with linksys support tonight they had me add port 3389 to port range triggering and disable the firewall on the home router. This didn't solve the problem. To recap: 1) I can connect to my work network with rdp from multiple public locations, but not at home with the iPad 2) I can connect to my work network at home with my laptop with the cisco client ant the windows rdp
View 6 Replies
View Related
Nov 5, 2012
After upgrading two laptops to windows 8, they will no longer appear as a connected device under the "device list." They both access the router via wifi and wired, but neither appear in the device list any longer. I've rebooted the router twice, as well as both computers, disabled/re-enabled their wifi connections, but no effect.Every other non-Windows 8 device still appears normally under the device list.
View 3 Replies
View Related
Jul 21, 2011
I have a big house so I have a e4200 on one end of the house upstairs and the WAP610n on the other end downstairs linked via CA6. I am having no issues with Laptops etc..just with Apple devices. I spent a lot of time with chat support (waste of time). WAP was flashed with latest firmware via hard wire no devices connected to wireless, has same ssid and security settings as router running on 2.4 ghz wpa2 personal AES. I am using 2.4 due to iphone4 does not support 5ghz and wap does not support dual band (another bummer). I am using AES instead of TKIP/AES mixed mode due to apple devices will not acquire dhcp with this setting and if they do they lose it right away. I have tried everything imaginable with the settings even changed beacon to 75, 50 RTS to 2304 etc...the current setting are the only ones that seem to work the best however when i run speedtest.net LA server or SD server the performance is horrible. On windows laptop i can achieve 27mbps down 2.5mbpsup, my apple devices use to achieve very close numbers to that on a simple configuration with two Dlink DGL-4300's one as router one as AP (G mode). So two major issues i have noticed is WAP610N has issues passing DHCP to apple devices and has extremely poor performance. So my question is will there be a firmware to correct this issue or a new hardware version that i can exchange this for if I RMA it or would it be best to call it a day and just get a E3200 and use it as a real simultaneous dual band AP???
View 9 Replies
View Related
Feb 22, 2013
I have noticed from time to time I get many (15-20) "network devices" in the Device List with no MAC address. I notice this mainly when managing Parental Controls. I go and clean up the Device List and days later they reappear. Another interesting thing is that the computer I am writing this with (through the router) does not show up in the Device List and I have an IP address from the router. I have the latest firmware 1.1.28.146856. Does anyone else see this on their EA6500?
View 2 Replies
View Related