How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 RepliesEvery time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading." This happens with FIrefox 11, and started when I upgraded to 8 or 9. A machine running FF 3.6 does not exhibit this problem; I get right in. What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
I ran Wireshark to see if I could learn anything, but all I could figure out was this: https handshake was OK. First TLS packet is received by router, which then immediately issues a reset and ends the connection. I don't know why.
have I got a screwed up configuration (or router)?
for the past couple of hours i've been trying to setup my router (Linksys WRT160N).When i set up all the cables, like it is in this picture:
[URL]....
I have" a WRT160N but I guess we had a power outage while I was on vacation and now I can't connect to my old network I set up.I see the Linksys internet connection and I can connect but its not the password protected one I set up. When I go to "manage connection" I can see the old "house" connection but can't connect
View 4 Replies View RelatedThis was for a WRT160n v3.0.02 I looked up several suggestions online and decided to update the firmware to v3.0.03 This seemed to only make it worse as I could no longer connect, and when I turned the router off and back on it would allow me in for about a minute and drop me right away.I started tweaking with the settings, and came across some posts here such as this one, started tweaking with the channel settings and everything. Nothing. If anything I somehow made it worse since now instead of dropping repeatedly it wouldn't connect at all except for about a minute after restarting router, then it would drop completely (I would either get the limited access notification or I simply couldn't connect and windows said to unplug the access point. I recalled I had another Linksys router that I wasn't using in storage, a WRT54G2v 1.0.01 so I set that up, no problems... at first. All other devices picked it up right away, but once again, my new laptop decides it's too good for the freaking network and drops it repeatedly telling me there's a problem with the access point.
So at this point I'm thinking it might NOT be my network, but my wireless card or something, I uninstalled and reinstalled, updated drivers, (I use a Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC) I even came across this article and disabled browser service and NETBios (including all other devices on my network). It brought back the network on my laptop for a bit, only to smugly come crashing down again.
I am unable to connect my Ipad3 to my home network (WRT160N router). It has been working for the last 8 months, and stopped working after I installed Direct TV App on Ipad..It detects the network, but not accepts the PW.... I have multiple wireless devicess connected to my network without any problems..The funny thing is that my neighbor brings his ipad to my house and he is able to connect..My ipad connects to any other network...just not my home network.. I contacted Apple who spend hours with me on the phone and suggested doing a full reset on the ipad, but still did not solve the problem..I called and already paid for linksys support ($62.95) who spend hours with me on the phone, but suggesting: "maybe you need to buy another router"...REALLY!!!! Again, I have 3 Smart TVs, Xbox360, and Wii, that are connected to the network just fine .even my neibor comes with his Ipad3 and connects to my network just fine......and I can connect with my ipad to any other network without any problems... BTW, I have already removed the DirectTV app from the ipad....but I still cannot connect to my network..
View 2 Replies View RelatedI have a desktop running XP. I am using comcast as my ISP. I have my printer attached to my Linksys wrt160N router via Ethernet. My desktop is also attached via ethernet. I also have a laptop attached to the router via wireless. How do I access the printer via the router from either the desktop or laptop? I had it configured properly in the past then lost my motherboard. Once the PC was rebuilt, I lost access.
View 6 Replies View Relatedsetup cd won't get past 25% and says not connected to the int! but yes i am .Also tryin to bridge with ATT PACE 4100n crapp!
View 2 Replies View RelatedI have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.
View 5 Replies View RelatedI have a new Linksys E1000, and I would like to connect my HP 2035 Laserjet to the router, avoiding connecting it directly to my desktop (wired to the router) or my laptop (wireless). When I connect the Ethernet cable to the printer and the router?Both PCs are running XP, and the printer was connected to the laptop before I got the wireless router.
View 2 Replies View RelatedI have downloaded the installation data "R147095 Dell Wireless Printer Adaptor 3300 Installation Set-UP.exe". Saved that to a new CD and loaded it to my PC. I get through most of the setup wizard but always fail at the same point - The adapter will not connect to the network. All the usual checks are positive and the network key is correct and in the appropriate case. I have run Driver Detective and that confirms that the drivers for the adapter are up to date. The printer is not yet installed on the PC and the software for it has not been loaded.
I have tried this procedure again on a second PC where the printer had been used as a wired slave printer but have uninstalled the printer first. Same result - Adapter fails to connect to the network.
Router is a Billion Bipac 7800 n. I can get other "newer" devices to connect without problems but this "old" adaptor is proving stubborn.
how to connect a network printer (HP OfficeJet Pro K8500DN) to the Cisco AE4500. Cisco's installation CD only believes there are USB or Wireless printers?
View 4 Replies View RelatedI was having problems with the speed being between 30-58 kpbs when going through the WRT160N router, whether its hooked up wired or wireless, the speed with both was extremely slow and wouldnt fully open pager or would take dsl day slow. I hooked up straight to modem and I got 100+ kpbs so I figured its not my ISP, so I read that upgrading my firmware might make it faster, so I upgraded and hit and held the reset button for 30 secs like it recommended but now the 192.168.1.1 wont open, I get a message saying it cant open this page
View 4 Replies View RelatedWill a realtek wireless network adapter connect to a Linksys WRT 110 router from a wood frame house to a concrete building approx. 100 ft. away
View 1 Replies View Relatedcan the linksys ae1000 adapter be use to hook a printer to the network?
View 1 Replies View RelatedSo, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200? How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
View 2 Replies View RelatedI'm having an issue getting my tv to start connecting again to the wireless router.Have tried pin setup (timed out & didn't connect...attempted at least 10 times in this fashion)Have tried entering the password (router seems to refuse the connection to the tv)About a month ago, I was in the Network Magic Map & it looked like one of the laptops had been cloned, so I removed it from the network.
View 3 Replies View RelatedHow do I connect IPAD to Linksys router WRT160n?
View 2 Replies View RelatedI have two computers on hard line and two laptops. All computers on the line work fine and flawlessly. But when I try to connect the laptops to the computer, they say there's a problem with the certificate. Both detect the connection, and with strong enough signal strength. I've tried WPA and WEP encryption methods, and disabling encryption methods. All had no change. I believe the problem lies with this Wi-Fi Protected Setup stuff, which I have no clue as to what the hell it's supposed to do. I've tried disabling it by turning it to manual, which all computers then lose internet connection entirely. Browsing the FAQ's, I havn't found a solution. I've been working on this thing for a solid 7 and a half hours straight, and phone support is trying to make me configure static IPs, which proved extremely inconvenient in the past.
View 9 Replies View RelatedI just bought a Linksys WRT160N router. I pop the installation disk in my mac book pro and walk thru the installation procedure successfully.But I can't connect wirelessly from my MacBook Pro (running mac os x 10.5).It sees the router and I did type in the password correctly (i copy from the text file generated by the installation procedure), but I keep getting 'coonnection timeout'.
View 9 Replies View RelatedI need to go two ways in my house to improve the wireless signal. Do I just run ethernet cable from the router to the access points? Do i then setup each AP?
View 1 Replies View RelatedI've been using a WRT160N for a couple of years now with no problems with any of my devices. I have a couple of certain devices (a DS and a PSP mainly) that utilize 802.11b and have been working perfectly up until now.
All of a sudden it seems like the router has decided all by itself to no longer allow 802.11b devices to connect to it, despite it being configured in mixed mode. (b/g/N) I've tried tinkering around with it, switching between Mixed and BG-Mixed, changing the channel to something more common and restarting the router, but I can't connect at all on these devices.Model: Cisco Linksys WRT160N v3.Firmware version: 3.0.03.
I cant get my laptop to connect to my wrt160n v3 router when wireless N is enabled my laptop supports b/g/n wireless.
View 5 Replies View RelatedI have a hard wired connection thought my cable modem, but can not get it thought my WRT160N v2
View 2 Replies View RelatedWindows 7 laptop does not connect to Wiress router WRT160N. It used to connect automatically for years when laptop is booted.Now Windows troubleshooting gives message to reboot wireless router. It connects automatically when the wireless is rebooted. This issue occues when the router is ON for long time ~ 12 hours or more.
View 1 Replies View RelatedI've been searching and searching the internet and I have never found a CERTAIN answer for if the linksys wrt160n v3 router will work for the ps3 or not. I want to know for sure if it will work because I know that is it sbackwords compatible with g/b/a networks but I am a newby at this stuff.
View 2 Replies View RelatedPurchased today 26th March 2012, used CD first as warned, followed procedures, will not connect to WAG 160N modem router. WAG160N has MAC restrictions but MAC of WRT160N added, both in wireless and as a computer. Still won´t connect, gets to 85% in wireless connect mode then fails, gets to stage 4 of router recognition and fails, saying check cables. Cables changed to know working ones, still no success. Tried pinging 192.168.1.1 direct from computer with no success, no access to router log-in page at all. WAG 160N has no problems.
View 2 Replies View RelatedI have just purchased a PC Tablet, but cannot add it to my network on my WRT160N Router.All I get is "Authenticating" then "Authenticating problem".
View 1 Replies View RelatedJust finished the setup for Canon MP780 USB printer to work with EA4500. Printer goes online only while it prints the pages. When I try to scan the document with MP Navigator it cannot communicate with the scanner as printer is essentially offline. How to setup the printer in order to perform the scan of the documents?
View 2 Replies View RelatedI am experiencing - loosing network connectivity entirely (between the router and the cable modem) or loosing connection to some clients: 2 wireless laptops - one N and one G, and 4 wired connections. This requires a reboot of the router 2-3 times a day. Never experienced any of these problems with a Linksys WRT54G, a unit that this one replaced. Unless I can resolve it, the WRT54G is going back in, and WRT160N is going back.
View 9 Replies View RelatedThe network is constantly disconnecting from my devices and wont let me reconnect...I reset the network completely back to factory settings and started from there. Some of my devices didnt want to connect at all after the complete reset.These are the settings that I have changed: SSID has been changed,wifi security(wpa2 personal,AES) ,channel(width=20, channel=auto) ,DNS server(changed to Norton DNS: 198.153.192.40 & 198.153.194.40) & router management logon password & firmware upgrade to 3.0.03...
Router:Linksys WRT160N V1
Firmware:3.0.03
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies View RelatedFor a while now, my wireless network at home has been very unreliable. I posted on these forums before, asking for assistance to fix crashes that seemed to be random. I was largely unsuccessful, and the problem continued. However, as I continued to experiment with different methods to keep my network up and running, I noticed that as long as I had at least one device connected to the network around-the-clock it never crashed. This was easy enough, as I own an iPod touch and a dock (I would leave it sitting it the dock unlocked all the time). But it's annoying to never be able to leave the house with it, and I'm ready to finally get a solution to the problem once and for all. I would prefer not getting a new router, but if worse comes to worse I will.
To sum it up:
-Works perfectly (when up) at full speed, never crashes unless there are no devices connected to it.
-When it does crash, it is very difficult to 'coax' it back into working again; it's been down for weeks at a time before.
-For some strange reason (and maybe this is a clue), newer game systems such as a Nintendo DSi or PS3 can make it start working again. I, of course, own neither of these.
-I'm using a WRT160N V3, latest firmware as far as i know.