Linksys Wireless Router :: Wrt160n - Original Network SSID Had Been Changed?
Oct 8, 2009
I have a wrt160n router set up at a friends house that i would connect my windows xp laptor to when i would go there. it always worked fine. i recently got a new laptop with vista 64 bit OS. i went to my friends today and connected via wireless for the first time. i expected to get prompted for the security key. instead it asked for the pin #. the pin number was something new i noticed when i replaced an older linksys with the new wrt160n so i had it in my notes. i entered the pin number and connected to the wireless router. but then my friend laptop could not connect and said it couldnt find the network. when i viewed the available networks, i noticed that the original network SSID had been changed to my vista laptop's computer name. i had to physically connect my laptop to the router and reconfigure the settings of the wireless network. then my friend was able to see the available network and automatically connect..
View 6 Replies
ADVERTISEMENT
Jun 16, 2008
I purchased a WRT160N router last Friday. After setting it up, everything seemed to work fine, but after a couple of hours, the router stopped responding to any requests. The LEDs stayed on as if nothing had happened, but the router was dropping everything coming from both the WAN and a wired LAN interface. Since than, I had to restart it 3 times during the last 3 days.The firmware is 1.53.0, which seems to be the latest firmware for the European market - even when I try to get a newer firmware, this site only offers the US version 1.02.2.Should I update the firmware to the US version 1.02.2 ? Is there any difference between the 1.53.0 and the 1.02.2 version ? Is there a way to restore the original firmware in case the update fails ? I haven't found any link to 1.53.0 version..Also, does this firmware updating affect my warranty ?
View 9 Replies
View Related
Jun 7, 2012
I recently upgraded the firmware on my wrt 160N v3 and changed the wireless security to WPA2 Personal from WEP (I needed to do this to get higher speeds from a recently purchased wireless adapter). Now the router stops transmitting a signal intermittently for about a minute before coming back on line. The time between droppages is also not the same. Before the firmware upgrade (and the change in security settings) the router was rock solid. Where I can get the older version of the firmware (which seems to be more stable than the current version)?
View 4 Replies
View Related
Jul 12, 2010
I have manually configured the E2000 and set the admin password. When I was trying to log back in, I could not. I reset and reconfigured and set the password again. I still could not log in using "admin" and the password I set up. I thought I was losing my mind. Just on a hunch, I used the SSID name instead of "admin", then entered the password that worked. I am able to login, but I need the username to be admin, not the SSID. Has anyine else had this issue? Any way to change the administrator name back to admin??
View 5 Replies
View Related
Jan 3, 2012
Recently, I bought the E3200, and tried to configure its ports for gaming. Yet, whenever I would hit save settings, it would say my settings were saved, then return me to the settings page. But the settings would be blank. I tried downloading firmware from the website (which should say September 28), yet it still says I am running the firmware from September 1st, even after I applied the upgrade and followed through with the 50 second reboot process.
So, I guess my final question for any tech savvy person out there is "What is wrong with my router/firmware?" I am running the browser config in the most recent Firefox on the same MacBook I used to install the router, and haven't changed any settings other than the SSID and password.
View 2 Replies
View Related
Nov 17, 2011
I have two router WRT160N & WRT120 N . They are working successfully with different SSID. Now I need one SSID. Need if found wi-fi signal week Another wi-fi take care automatically.
View 5 Replies
View Related
Oct 15, 2011
Been using the WRT160N for a while now and it works great except for one issue. Every few weeks the wireless can't be accessed by the other computers unless I change the SSID name. It was frustrating to figure out, but simply changing the name makes it accessible again.
View 1 Replies
View Related
Jul 8, 2011
i bought a WRT160N router
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
View 3 Replies
View Related
Feb 27, 2011
router is a d link dsr 2460r. got a student at my house with big uni exam on friday
View 6 Replies
View Related
Aug 11, 2011
I have" a WRT160N but I guess we had a power outage while I was on vacation and now I can't connect to my old network I set up.I see the Linksys internet connection and I can connect but its not the password protected one I set up. When I go to "manage connection" I can see the old "house" connection but can't connect
View 4 Replies
View Related
Dec 27, 2012
I have just purchased a PC Tablet, but cannot add it to my network on my WRT160N Router.All I get is "Authenticating" then "Authenticating problem".
View 1 Replies
View Related
Jun 28, 2012
If someone has the original firmware for the EA3500 to copy. I need to downgrade my router after Cisco sabotaged it with their Cloud Connect. This will be the firmware you have right out of the box. Be sure you go into the Admin. section and Save a Copy before you ever connect to the Internet. Also Uncheck the Auto Updates box or you will be fed the Cloud Connect (and its amazing Terms Of Service).
View 6 Replies
View Related
Jan 11, 2012
I have new PC with Window 7 and trying to set up E2000 on new computer with original set up CD. States I need go back to my old computer and set up new key and transfer to new computer. I do not have access to old computer. getting set up on new computer?
View 3 Replies
View Related
Feb 23, 2008
I am experiencing - loosing network connectivity entirely (between the router and the cable modem) or loosing connection to some clients: 2 wireless laptops - one N and one G, and 4 wired connections. This requires a reboot of the router 2-3 times a day. Never experienced any of these problems with a Linksys WRT54G, a unit that this one replaced. Unless I can resolve it, the WRT54G is going back in, and WRT160N is going back.
View 9 Replies
View Related
Aug 15, 2009
I'm trying to reset this router back to its original form (pass: admin (?)) but the ''hold the reset button for 45 seconds and unplug for 30 seconds'' just doesn't seem to work. When I try to install with the CD it just keeps saying that I have to reset it. how do you reset the WRT120N? Are the lights suppose to blink to indicate that you're done holding the reset bottom?
View 9 Replies
View Related
Mar 15, 2012
I updated my E3000 firmware to Ver. 10.0.4 and did not backup the original firmware. How I can get the original firmware file for this router.
View 3 Replies
View Related
May 30, 2007
It appears that there is no firmware I can download for my WRT54GL Version 1.1. While it may never have been updated from what the router came with from the factory, it would still be useful to have it available. In my case, I would like to revert the router from the DD-WRT firmware to factory specs.
View 3 Replies
View Related
Dec 31, 2012
The network is constantly disconnecting from my devices and wont let me reconnect...I reset the network completely back to factory settings and started from there. Some of my devices didnt want to connect at all after the complete reset.These are the settings that I have changed: SSID has been changed,wifi security(wpa2 personal,AES) ,channel(width=20, channel=auto) ,DNS server(changed to Norton DNS: 198.153.192.40 & 198.153.194.40) & router management logon password & firmware upgrade to 3.0.03...
Router:Linksys WRT160N V1
Firmware:3.0.03
View 9 Replies
View Related
Sep 27, 2011
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies
View Related
Jun 24, 2012
This was for a WRT160n v3.0.02 I looked up several suggestions online and decided to update the firmware to v3.0.03 This seemed to only make it worse as I could no longer connect, and when I turned the router off and back on it would allow me in for about a minute and drop me right away.I started tweaking with the settings, and came across some posts here such as this one, started tweaking with the channel settings and everything. Nothing. If anything I somehow made it worse since now instead of dropping repeatedly it wouldn't connect at all except for about a minute after restarting router, then it would drop completely (I would either get the limited access notification or I simply couldn't connect and windows said to unplug the access point. I recalled I had another Linksys router that I wasn't using in storage, a WRT54G2v 1.0.01 so I set that up, no problems... at first. All other devices picked it up right away, but once again, my new laptop decides it's too good for the freaking network and drops it repeatedly telling me there's a problem with the access point.
So at this point I'm thinking it might NOT be my network, but my wireless card or something, I uninstalled and reinstalled, updated drivers, (I use a Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC) I even came across this article and disabled browser service and NETBios (including all other devices on my network). It brought back the network on my laptop for a bit, only to smugly come crashing down again.
View 2 Replies
View Related
Nov 6, 2011
For a while now, my wireless network at home has been very unreliable. I posted on these forums before, asking for assistance to fix crashes that seemed to be random. I was largely unsuccessful, and the problem continued. However, as I continued to experiment with different methods to keep my network up and running, I noticed that as long as I had at least one device connected to the network around-the-clock it never crashed. This was easy enough, as I own an iPod touch and a dock (I would leave it sitting it the dock unlocked all the time). But it's annoying to never be able to leave the house with it, and I'm ready to finally get a solution to the problem once and for all. I would prefer not getting a new router, but if worse comes to worse I will.
To sum it up:
-Works perfectly (when up) at full speed, never crashes unless there are no devices connected to it.
-When it does crash, it is very difficult to 'coax' it back into working again; it's been down for weeks at a time before.
-For some strange reason (and maybe this is a clue), newer game systems such as a Nintendo DSi or PS3 can make it start working again. I, of course, own neither of these.
-I'm using a WRT160N V3, latest firmware as far as i know.
View 9 Replies
View Related
Aug 4, 2011
here is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
View 1 Replies
View Related
Apr 11, 2013
i have 7 AP's in a school...i have numbered them 1 to 7 and have a strong password on im being called out every few months to reset the AP as its not working when i get there i see the ssid has changed to hp-josh1a seems like a computer name (its different most times) how are they changing the ssid of the tp link?
View 14 Replies
View Related
Jan 13, 2012
Often my router drops connection to all my devices. Multiple times a day. It's only for a minute or so, but it's annoying. I'm using a Linksys Wireless-N router (WRT160N) with WEP encryption. I'm running two Windows 7 laptops, LG BluRay player, Apple TV, Xbox 360 (Wired) iPhone 4, and a iPad 2. It doesn't matter if I'm browsing the web, watching Netflix, or playing a game, the connection gets lost. As we speak it happened again. I have no clue on what to do. I've reconfigured it multiple times. Firmware has been updated months ago.
View 6 Replies
View Related
Jul 30, 2011
How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 Replies
View Related
Dec 12, 2012
I am unable to connect my Ipad3 to my home network (WRT160N router). It has been working for the last 8 months, and stopped working after I installed Direct TV App on Ipad..It detects the network, but not accepts the PW.... I have multiple wireless devicess connected to my network without any problems..The funny thing is that my neighbor brings his ipad to my house and he is able to connect..My ipad connects to any other network...just not my home network.. I contacted Apple who spend hours with me on the phone and suggested doing a full reset on the ipad, but still did not solve the problem..I called and already paid for linksys support ($62.95) who spend hours with me on the phone, but suggesting: "maybe you need to buy another router"...REALLY!!!! Again, I have 3 Smart TVs, Xbox360, and Wii, that are connected to the network just fine .even my neibor comes with his Ipad3 and connects to my network just fine......and I can connect with my ipad to any other network without any problems... BTW, I have already removed the DirectTV app from the ipad....but I still cannot connect to my network..
View 2 Replies
View Related
Jan 13, 2012
I had something odd happen to my Dlink router DIR-651 model. During the early evening hours someone changed the SSID name of my Router. Nothing else changed that I could see right off. So I reset the router to Factory Defaults.
View 1 Replies
View Related
Jan 25, 2012
I have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies
View Related
Jan 7, 2013
just bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies
View Related
May 28, 2012
i have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies
View Related
May 26, 2012
Is it possible to change one's private network name as well as SSID?
View 1 Replies
View Related
May 17, 2010
home router is a wrt160n v3 With my iPad I set up the built in IPSec VPN to my office's cisco gateway. I successfully get the VPN logo. With an RDP app, i can access my work network from multiple public locations from my iPad. At home, on my laptop, I start the cisco client then use the windows rdp, presto i'm in my work network. At home on my iPad I can activate the VPN, but I can not connect with rdp. I spoke with linksys support tonight they had me add port 3389 to port range triggering and disable the firewall on the home router. This didn't solve the problem. To recap: 1) I can connect to my work network with rdp from multiple public locations, but not at home with the iPad 2) I can connect to my work network at home with my laptop with the cisco client ant the windows rdp
View 6 Replies
View Related
Sep 7, 2011
i have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
View 1 Replies
View Related
