I have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 RepliesIs it possible to change one's private network name as well as SSID?
View 1 Replies View RelatedI just purchased a E2500 wireless router to upgrade from the previous G- router which I was using. I'm not very experienced in tech issues and would like to know, what would be the easiest way to extend my wireless signal through out the house. The E2500 which I just purchased does not cover all the areas in my household.
View 1 Replies View RelatedI have two WRT54GS routers. I want to extend my WiFi from the router connected to my upstream in the office to a second router in the living room. I want devices configured for the SSID and passphrase of my current WiFi (which is find in the office) to work seamlessly in the living room. I understand I can do this by running a cable and configuring router 2 as a client of router 1 with router 2 exposing the same SSID and passthrase on a different channel.
But I really don't want to run a cable.There is a point where a client can see router 1 where an AP would cover the living room.
Can I put router 2 at that point, have it connect wirelessly as a client to router 1, and have it expose as an AP using the same SSID and passphrase? Can this be done without wiring the router?
I just bought a Linksys E2500, and I'm trying to configure multiple SSID's on it. The "guest mode" won't work for me because I want one SSID to use WPA and the other to use WEP, but the option to set different encryption based on the GHz frequency of the connection won't work for me because I only want the WEP one to be used by my Nintendo DS (which doesn't support WPA); I don't want to force ALL devices that don't support 5GHz to use the WEP one!
View 9 Replies View RelatedNone of my wireless devices (Windows, iphones) can see the SSID from the 5ghz channel on my E2500. I have updated the firmware and reset the router to factory defaults. Still not visible. The router is set up to broadcast the SSID under wireless settings. Also, selecting "other" under iphone>settings>wifi and entering the SSID name and password gets "could not find the network (ssid)". This was working until a couple of days ago Comcast power cycled the router to make sure my cable modem was working. Now nothing.
View 2 Replies View Relatedwhy my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
View 4 Replies View RelatedI've recently purchased the E2500, done the setup but am facing some issues.I'm unable to see the 5GHz channel SSID, I can only see the 2.4GHz channel SSID.Have tested all the laptops and devices at home and all can't see the 5GHz channel.The list of devices are:
a) iPhone 3GS
b) iPhone 4G
c) iPhone 4GS (some sites says it doesn't support, some says it does, I'm confused as a result)
d) Samsung laptop
e) Dell laptop
f) Momo11 Little Bird Edition tablet (Made in China [MIC])
g) No name MIC tablet
Secondly, is there any tips / tricks to tweak the modem to increase the internet speed?
I just got a new E2500 and out of the box the system uses the same SSID for 2.4 GHz and 5 GHz. Obviously you CAN configure them to use different SSID's, though. Should I make them different or keep them the same? I don't really want to mess around with having 2 different SSID's if I don't get a real benefit.Will most devices that support both (like a new laptop) find and use the 5 automatically?
View 7 Replies View RelatedJust got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies View RelatedHow do you have the WAP610N and WRT610N using the same SSID? I would prefer to have my WAP610N simply just extend my network instead of broadcasting another.
View 1 Replies View RelatedI currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View RelatedI have the WRT610N, and I was wondering if there is a way to repeat the 5GHz network to extend the range.I am trying to stream content from a Blu-Ray player, and while the 2.4GHz network reaches, the signal is very weak. The 5GHz network doesn't reach, but I would prefer to stream content through that network than the 2.4GHz.
View 7 Replies View RelatedI would like to know what to buy to extend the range of my wireless network , which will not reach throughout my house.
Also, I would like to know what the button is for on the front of of the router, since it is not a WPS button, according to ATT.
I have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2? Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?I can't stand the interface. The E4200v2 is brand new.
View 1 Replies View RelatedIs it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how?
View 2 Replies View RelatedI have an 1131ag AP attached to our 5508 as an OEAP over the Internet. Everything with the corporate SSIDs is working correctly, so no issue there. I was wondering if a local ssid can be configured on the AP, similar to what can be done with the OEAP600, in order to provide wireless access to the Internet only? On the WLC, on the H_REAP tab, there is a button labeled "Reset Personal SSID"
View 3 Replies View RelatedI am trying to extend my home network into my basement with both wired and wireless connections. I have a WRT120N upstairs, which is connected to my cable modem. I have an E1200 in the basement, which I have connected with a LAN port. DHCP is turned off, and all wired connections are getting an address from the upstairs router, and connecting to the internet successfully.I've configured the wireless with the same SSID on both routers, but the clients that connect to the downstairs wireless are not able to access the internet. They are getting an IP address from the upstairs router, but can't get past the gateway.
View 1 Replies View RelatedI have the following equipment
E2500 wireless N router (2 of these)
WRT54g router (B/G)
WAP54g access point (B/G)
I am planning to set up a Wi-Fi network for a single story motel. It is C-shaped; about 300 feet along the longest side with "legs" of 120 and 70 feet.Until now I have only used that single WRT54g in the office for the entire property and it covers about half the property (left side.) My plan starts in the office (bottom left) with a WRT54g connected to the DSL modem as it always was. That would be connected to one of the E2500s in the middle so it can cover the most area. From there two others would shoot out to each corner (the other E2500 and the WAP54g). They will all be wired together with Cat 5e "riser cable". The routers will be placed in a wide open attic.
1. I have heard that N routers have a range of 150ft in every direction so that's why I'm putting one in the middle. Keep in mind that while the attic is open and wood constructed, the walls between rooms are concrete firewall and they haven't been wi-fi friendly.
2. Does starting with a B/G router at the modem mean the N routers will revert to B/G?
I have a new Siemens router and have set up my old LinkSys router as a switch (set DNS outside the IP range of the primary router, disabled DHCP server, connect LAN to LAN port).The SSIDs are still different. As a result each device now sees 2 networks and although internet GW is available from either connection, not al resources are shared across the network. There is one driveshare (with wired connection to the secondary switch) which cannot be seen by some of the wireless resources on the same secondary network.Questions:1. How can I set up the NW config such that it is seen and behaves like one physical network, anbd roaming devices pick up the signal from the strongest access point?
View 3 Replies View RelatedI have a E2500 connected to a cable modem as the base of my home network. Hard wire connected to the E2500 is an linksys 8 port hub and a couple of computers. The 8 port hub is connected to a couple of computers and a xbox. I have the hub as a distro point to cut down on wiring. Wirelessly connected to the E2500 are a variety of laptops, netbooks, ipods, an ipad, a playbook, an iphone, a android phone, a wireless printer and a Ps3. Most of the devices are just using the wifi for internet access. Most devices have been setup with their own ip addresses to avoid ip conflicts. The computers and laptops/netbooks are running either Windows XP, Windows 7 or Mepis Linux. Up until now everything was going as good as can be expected, all the computers could see each other and most could transfer files between each other except when Windows gets picky.In the last few days no computers can see each other. Windows or Linux.Everything can accsess the internet and wirelessly print still just can't see each other. I reset the E2500. I updated the firmware on the E2500. I installed the Cisco Connect software (just in case I was too stupid too setup a router). Still nothing. I can ping other machines from a command prompt in windows or a terminal in Linux and get a good ping back. In the router setup via a browser I can go to the status page and see other devices on the local network but most are just ipods, ipad, playbook and the wireless printer, If I go to the administration page / diagnostics I can ping other computers and get a good answer. I just can see them from each other. I think I've rebooted every thing at least once. Yes the workgroup names are all the same (workgroup) and yes file sharing is turned on on all computers.
View 3 Replies View RelatedSwitched from a Netgear router to a Cisco E2500 and now my Samsung blue ray won't connect to internet.
It says physical connection established but can't connect to external network.
I set up a linksys e2500 router with name "mynetwork" and WPA2 password.
The network works fine, my laptop connects securely to it.
But when I View Available Wireless Networks , I see a second , unsecure network named "mynetwork-guest" to which my laptop will also connect with no credentials (not sure how that network got there).
How can I find and delete that unsecure network? When I go into my router setup, I only see mynetwork, not mynetwork-guest If it is of any use here is the IP information for both:
The settingd for mynetwork:
IP Address: 192.168.1.133
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
The setting for mynetwork-guest:
IP Address: 192.168.33.137
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.33.1
just bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies View RelatedIn the process of setting-up a E2500 Linksys router, I set-up my secured network which is working fine but also (I do not know how I did this??) set-up the same named network but it is unsecured. How do I delete this unsecured network.Do I need to set-up the router again?
View 4 Replies View RelatedI currently use a E2500 router for my home network. I have setup the Wireless guest Network for my downstairs Tenant while he is out of work so he can still have some internet. The problem however is that often the guest network will take up 90% of my 55mb/sec bandwidth, leaving none for the primary network. Is there a way for me to Throttle the amount of bandwidth the Guest network can use? Say alot 10mb/sec for Guest access only, and leave the rest for our main network?
View 6 Replies View RelatedI'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?
View 8 Replies View RelatedI have a Linksys E2500 router. Is it possible to have one network name for the secured network and a different network name for the Guest network? The thought is to not have the SSID of the secured network broadcast while allowing the SSID of the Guest network to be broadcast. With the convention of simply adding "Guest" to the end of the SSID for the secured network, it defeats the security option of not having the SSID of the secured network broadcast.
View 1 Replies View Relatedhere is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
I am trying to extend the wireless network at our church beyond a firewall to another area of the builing. We have a cat 5 cable run through the firewall to the other side. I have a brand new Linksys E2500 router. Can I assign an IP to this router and connect it's WAN "Internet" port to one of the ports on the main router that is connected to the cable modem and use it to extend our network?
View 1 Replies View Relatedi have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies View RelatedI have a wrt160n router set up at a friends house that i would connect my windows xp laptor to when i would go there. it always worked fine. i recently got a new laptop with vista 64 bit OS. i went to my friends today and connected via wireless for the first time. i expected to get prompted for the security key. instead it asked for the pin #. the pin number was something new i noticed when i replaced an older linksys with the new wrt160n so i had it in my notes. i entered the pin number and connected to the wireless router. but then my friend laptop could not connect and said it couldnt find the network. when i viewed the available networks, i noticed that the original network SSID had been changed to my vista laptop's computer name. i had to physically connect my laptop to the router and reconfigure the settings of the wireless network. then my friend was able to see the available network and automatically connect..
View 6 Replies View RelatedI would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0.0.0/24) How can I forward different ports to this 3 different private networks with an E2500.Under "Games&Applications" in the" Portforwarding" menu the first 3 octets of the "to IP-address" are fix and corresponds ever with the LAN ip address of th E2500.
View 4 Replies View Related