I have an 1131ag AP attached to our 5508 as an OEAP over the Internet. Everything with the corporate SSIDs is working correctly, so no issue there. I was wondering if a local ssid can be configured on the AP, similar to what can be done with the OEAP600, in order to provide wireless access to the Internet only? On the WLC, on the H_REAP tab, there is a button labeled "Reset Personal SSID"
View 3 RepliesI have setup a 1131 with multiple ssid's, they show up, but neither one will connect. i need 2 ssid's, one open and one protected. this is the config i have so far:
[code]....
Just recently got a new 881W router. i have downloaded the 2.4 software upgrade. I go into the Office extend AP login and i get just a enter button. when i click on the enter button the AP page does not come up.
View 7 Replies View RelatedI have finally got my office extend AP to connect to my companies 5508 controller by enabling NAT on the management interface and can see all the cooperate SSID's. However when I try to connect to the SSID my client either gets a local IP address from my home router or then cannot get any IP address.
View 9 Replies View Relatedi'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies View RelatedI am having an issue with internal and external clients. When we have the nat ip configured on the controller we cannot connect internal ap's at all. When we take the nat ip out it works fine. We are on code 7.0.220. I have tried the following command <config network ap-discovery nat-ip-only disable> and it did nothing.
View 1 Replies View RelatedDoes cisco 3600 support office extend feature? If yes, is there a controller requirement? I know cisco AP 600 supports office extend
View 24 Replies View RelatedI am setting up office extend with 1142 APs on a 5508 controller. All seems ok and I see my SSIDs on the remote AP. However when I try to connect I don't get a dhcp address and the connection fails. When I look at logs and some debugs I see dtls keepalive failures and the AP is actually disconnecting and re-associating with the controller.
View 24 Replies View RelatedIf we have a mixed environment of 4400 and 5500 controllers will the office extend features still work or will we have to run a seperate wireless domain from the 5508 for the aps that we need office extend on?
View 2 Replies View RelatedI have a situation where a user needs more than one office extend AP in his home. My office extend controller is a 5508 running 7.0.220.0. Are there any issues NATing multiple OE APs to a single address? My initial lab results indicate that each of the AP's associate with the controller and establish a DTLS tunnel. I see the SSIDs get pushed to the AP and then it seems to restart the process never being fully operational. Is there a workaround that will allow me to run mutliple OE APs?
View 12 Replies View RelatedWe're looking at deploying both office extend and also a guest wlan. Both would require a WLC in the DMZ.My question is can one 5508 WLC be both a guest anchor and have office extend APs on it at the same time?
View 2 Replies View RelatedI have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies View RelatedHow the ACL Ports/Protocols which must be opened (in- and outbound) to enable a communication between a CISCO Office extend AP and a 5508 WCS.
View 3 Replies View RelatedI have attached a diagram of the current topology. At present, we have two 5508 connected to our core. We also have a 4402 behind the firewall (DMZ) just purely for guest access. So the staff users connect to the access point which in turns connects to the Staff WLC 1 (if this fails then to Staff WLC2). any guest user connect to the access point which in turn connects to Staff WLC which anchors to Guest WLC which then provides access. Since the guest is behind the DMZ they can only access the internet and not out internal network.
Now we want to office extend our network - we want our users to use 1132 AP at home to access the Infrastructure. is there a way we can do this without disturbing the existing infrastructure. On reading Cisco website, i know the best practice is to use 2 5508 (one behind the firewall and the other anchored to this access the internet network ) i thought since we have a Cisco (dmz) switch (48 port) and only the 4402 (Guest WLC) is connected to it, maybe purchase another 5508 WLC and connect to the 48 port Cisco (dmz) switch. will this work?
I have two WRT54GS routers. I want to extend my WiFi from the router connected to my upstream in the office to a second router in the living room. I want devices configured for the SSID and passphrase of my current WiFi (which is find in the office) to work seamlessly in the living room. I understand I can do this by running a cable and configuring router 2 as a client of router 1 with router 2 exposing the same SSID and passthrase on a different channel.
But I really don't want to run a cable.There is a point where a client can see router 1 where an AP would cover the living room.
Can I put router 2 at that point, have it connect wirelessly as a client to router 1, and have it expose as an AP using the same SSID and passphrase? Can this be done without wiring the router?
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies View RelatedI have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example 172.25.25.4), but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is 192.168.25.4 - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
[Code]......
I have WLC 4402 with software IOS 5.2.157.0 and i am planing to upgrade the sofware to the latest one (7.0.235.0)
now my question are :
1 - is that software version will support APs [AIR LAP 1131 AG-E-K] ?
2- on down load page there 2 files :
a) Cisco Unified Wireless Network Controller Boot Software 7.0 for Cisco 4400 Series Wireless LAN Controllers.
b) Cisco Unified Wireless Network Software Release 7.0 for Cisco 4400 Series Wireless LAN Controllers. which file i need to upload on my WLC 4402
I have an AP(1131) that keeps disassociating from the controller. It stays alive for about 10 mins then it doens't work anymore. I tired changing the AP but that didn't make a difference. I also tried changing the port on your 500 POE switch. My last effort to fix it was to put the AP on a 3550 switch with a power injector. Still no luck.
I don't understand why its doing this. I am able to connected to it and surf the internet for about 10 mins. After that It leaves the controller and just cycles through different colors.
I have some questions about this AP and it's IOS. I have some AP's 1131 and they have IOS 12.34(3g) JA I'm working with a 4402 WLC I'm going to change this WLC for one 5508 but this WLC has a different version software it has 7.2.103. My questions is I need to do any upgrade to my AP's IOS for join to the new WLC ?
I found a compatibility Matrix, in this document I guess i nedd to do some upgrade: URLs
The WGB can be any autonomous access point that supports the workgroup bridge mode and is running Cisco IOS Release 12.4(3g)JA or later releases (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later releases (on 16-MB access points). These access points include the AP1120, AP1121, AP1130, AP1231, AP1240, and AP1310. Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.
Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a 5.1.151.0 in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that 5.1.151.0 dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
AP
LWAPP Static IP Configuration
IP Address 172.18.240.244
IP netmask 255.255.255.192
Default Gateway 172.18.240.193
[Code]....
How to shut off wireless admin access on a 1131 AP? I only want to be able to administer the device via the wired LAN. I need to shut of http, ssh, and telnet.
I haven't been able to find anything in the GUI.
How to know the CLI commands?
I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.
View 12 Replies View Relatedi have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
I want to install lightweight IOS into Aironet 1131AG by using Upgrade Tool. However, some error messages appear saying:
1. ACL / Firewall might be blocking the TFTP.
2. Disable the ACL/Firewall setting for TFTP.
I don't set up any ACL because I am trying to install to the Aironet which was just initialized by using mode button. Configuration is just like followings.
Is there any possibility that the configuration block the TFTP communication ? now, ping is reachable and directly, I am connecting AP and PC with upgrade tool . and windows firewall is disable on the PC. But the upgrade tool is error. Why the TFTP communication is failed.
Building configuration...
Current configuration : 1361 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log date time msec service password-encryption!host name ap!no aaa new-mode[ code]...
We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.
I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
Cisco Air 1131 AP. Having problems with Apple products. Even tried no security.
View 2 Replies View RelatedI configured DHCP pool on Cisco AP 1131, Laptop users are working fine and obtain IP address from AP 1131 DHCP Server, but IPad user is getting IP problem when he try to connect Cisco AP 1131.when i reboot the AP, IPad user getting IP address from 1131 AP dhcp server and access the network resource for the 2-3 hr after that IPad show "obtaining ip address from .....".
AP Detail-
AIR-AP1131AG-N-K9
c1130-k9w7-tar.124-10b.JA2
12.3(8)JEA
I have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.
View 3 Replies View RelatedI do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. can i convert without connecting to WLC .
View 1 Replies View Related