Cisco Wireless :: AP 1131 Won't Join WLC

Jan 31, 2013

I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.

View 19 Replies


Cisco Wireless :: No Join Request Going Out With 1131

Aug 10, 2011

Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
LWAPP Static IP Configuration
IP Address
IP netmask
Default Gateway

View 8 Replies View Related

Cisco Wireless :: Configure 1131 AP With 2 Ssids

Jun 15, 2012

I have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:

gibbs#show run
Building configuration...
Current configuration : 3272 bytes
version 12.4


View 4 Replies View Related

Cisco Wireless :: AP 1131 Upgrading To LWAP

May 20, 2012

We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example, but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.

View 9 Replies View Related

Cisco Wireless :: AIR-LAP 1131 Reboot In Loop?

Mar 4, 2013

I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990


View 15 Replies View Related

Cisco Wireless :: AIR LAP 1131 AG-E-K Supported WLC Software IOS?

Jul 31, 2012

I have WLC 4402 with software IOS and i am planing to upgrade the sofware to the latest one (
now my question are :
1 - is that software version will support APs [AIR LAP 1131 AG-E-K] ?
2- on down load page there 2 files :
a) Cisco Unified Wireless Network Controller Boot Software 7.0 for Cisco 4400 Series Wireless LAN Controllers. 

b) Cisco Unified Wireless Network Software Release 7.0 for Cisco 4400 Series Wireless LAN Controllers.  which file i need to upload on my WLC 4402

View 13 Replies View Related

Cisco Wireless :: 1131 - AP Keeps Disassociating From The Controller?

Mar 3, 2010

I have an AP(1131) that keeps disassociating from the controller. It stays alive for about 10 mins then it doens't work anymore. I tired changing the AP but that didn't make a difference. I also tried changing the port on your 500 POE switch. My last effort to fix it was to put the AP on a 3550 switch with a power injector. Still no luck.
I don't understand why its doing this. I am able to connected to it and surf the internet for about 10 mins. After that It leaves the controller and just cycles through different colors.

View 18 Replies View Related

Cisco Wireless :: 1131 AP12.4 JA And 5508 V7.2

Jun 4, 2013

I have some questions about this AP and it's IOS. I have some AP's 1131 and they have IOS 12.34(3g) JA I'm working with a 4402 WLC I'm going to change this WLC for one 5508 but this WLC has a different version software it has 7.2.103. My questions is I need to do any upgrade to my AP's IOS for join to the new WLC ?
I found a compatibility Matrix, in this document I guess i nedd to do some upgrade: URLs

The WGB can be any autonomous access point that supports the workgroup bridge mode and is running Cisco IOS Release 12.4(3g)JA or later releases (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later releases (on 16-MB access points). These access points include the AP1120, AP1121, AP1130, AP1231, AP1240, and AP1310. Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.

View 21 Replies View Related

Cisco Wireless :: 1131 - No SSID Connecting

Oct 28, 2012

I have setup a 1131 with multiple ssid's, they show up, but neither one will connect. i need 2 ssid's, one open and one protected. this is the config i have so far:

View 8 Replies View Related

Cisco :: 1131 - Shut Off Wireless Admin Access On AP

Apr 21, 2011

How to shut off wireless admin access on a 1131 AP? I only want to be able to administer the device via the wired LAN. I need to shut of http, ssh, and telnet.
I haven't been able to find anything in the GUI.
How to know the CLI commands?

View 6 Replies View Related

Cisco Wireless :: DHCP On 1131 Access Point

Jul 21, 2012

I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.

View 12 Replies View Related

Cisco Wireless :: Air-lap-1131-ag-e-k9 - How To Convert To Autonomous Mode

May 7, 2013

i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to set subnet mask to, default gateway to
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.

View 20 Replies View Related

Cisco Wireless :: 1131 - Upgrade Tool Error

Mar 22, 2012

I want to install lightweight IOS  into Aironet 1131AG by using Upgrade Tool. However, some error messages appear saying:

1. ACL / Firewall might be blocking the TFTP.
2. Disable the ACL/Firewall setting for TFTP.
I don't set up any ACL because I am trying to install to the Aironet which was just initialized by using mode button. Configuration is just like followings.

Is there any possibility that the configuration block the TFTP communication ? now, ping is reachable and directly, I am connecting AP and PC with upgrade tool . and windows firewall is disable on the PC. But the upgrade tool is error. Why the TFTP communication is failed. 

Building configuration...
Current configuration : 1361 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log date time msec service password-encryption!host name ap!no aaa new-mode[ code]...

View 4 Replies View Related

Cisco Wireless :: 5508 WLC Associates With 1131 / 1242 But Not 3602i?

Apr 25, 2012

We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.

View 6 Replies View Related

Cisco Wireless :: AP 1131 AG Do Not Associate To Controller 5508 Or 4402

Apr 18, 2013

I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.

View 4 Replies View Related

Cisco Wireless :: IPADs Iphones And Macs Do Not Connect 1131

Sep 8, 2011

Cisco Air 1131 AP.  Having problems with Apple products.  Even tried no security.

View 2 Replies View Related

Cisco Wireless :: AP 1131 DHCP Server Connectivity Between IPad And AP

Jul 17, 2012

I configured DHCP pool on Cisco AP 1131, Laptop users are working fine and obtain IP address from AP 1131 DHCP Server, but IPad user is getting IP problem when he try to connect Cisco AP 1131.when i reboot the AP, IPad user getting IP address from 1131 AP dhcp server and access the network resource for the 2-3 hr after that IPad show "obtaining ip address from .....".
AP Detail-

View 1 Replies View Related

Cisco Wireless :: 1131 Ap Working With 5108 Controller But Not With 2125

Dec 23, 2012

I have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for  Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.

View 3 Replies View Related

Cisco Wireless :: AP 1131 As Office Extend With Local Ssid?

Feb 15, 2012

I have an 1131ag AP attached to our 5508 as an OEAP over the Internet.  Everything with the corporate SSIDs is working correctly, so no issue there.  I was wondering if a local ssid can be configured on the AP, similar to what can be done with the OEAP600, in order to provide wireless access to the Internet only?  On the WLC, on the H_REAP tab, there is a button labeled "Reset Personal SSID"

View 3 Replies View Related

Cisco Wireless :: 1131 Light Weight AP To Autonomous Conversion Without Controller

Jan 15, 2013

I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. can i convert without connecting to WLC .

View 1 Replies View Related

Cisco WAN :: 1131 - LED Blinking Red And Off

Sep 28, 2011

I have the 1131 hardware manual and it is stating that this is caused by a boot loader issue or the AP did not get the IOS file from the controller. We have a Cisco 4404 controller that this AP reports to. It was one out of 30 and after a reboot it is working fine. What can i do in the future to catch this and prevent this from happening.

View 1 Replies View Related

Cisco :: Does WLC 520 Support AP-1131 Or Not

May 1, 2012

I have WLC 520 with software version 5.2.178. Currently we purchased Cisco   AIR-LAP1131G access points and tried to join to WLC 520 but it is not joining. My question is WLC 520 will support 1131G access pont or not.?

View 1 Replies View Related

Cisco :: Configure WPA2 On 1131 AP?

Mar 6, 2013

I, at work, have recently deployed a very small stub network in Papua New Guinea, an office that has no more than 7/8 users.  This simple network consists of:
1 x 2611xm Router
1 x 2960 24port Catalyst Switch
1 x 1131ag AP


View 2 Replies View Related

Cisco :: 1131 AP And Controller Not Showing CDP?

Feb 29, 2012

I have several APs directly connected to a Cisco 3560 and each port is configured this way....
interface FastEthernet0/1
description Uplink To  Access Point
switchport trunk encapsulation dot1q

The switch shows the AP under sho cdp niegh but when I go to the controller and look at AP neigh nothing shows up. I am currently running a WLC 4404 with 4.2.209 ( yes the upgrade happens tomorrow ).
why the switch shows the neigh. but not the AP when looking from the controller?

View 4 Replies View Related

Cisco :: Changing Management Vlan On 1131 AP

Jun 29, 2011

Can I change the untagged vlan on a 1131 to a new vlan.  I need to move my management vlan from on vlan 1 , to on vlan 200. I attempted several configuration options including removing the vlan1 ip,  changing my new vlan200 to untagged and mirroring it on the switch,  and adding my new ip to vlan 1 untagged and then untagging the switch with access vlan 200 on the connected port.  Nothing worked.  
Below is a sample of what I changed:
interface Dot11Radio1
no ip address
no ip route-cache


View 1 Replies View Related

Cisco :: WLC And 1131 AP's - Users Unable To Connect

Jan 21, 2011

I've ran into an issue that I haven't seen before.  A client of mine has a WLC that manages AP's at several different sites on the East Coast.  They are all connected via a multilinked T1x2 connection.  One site in particular contains 7 AP's, and users at this site are unable to connect.  The remaining sites have no issue at all connecting.  I noticed that when users began reporting this that all AP's had failed interference profiles.  Also, when I instruct a user to attempt a connection, I don't ever see their mac address come across a debug session on the controller, which I find odd.  Is it possible that a neighboring business is sending deauth packets and containing my AP's?
The client is running code version

View 2 Replies View Related

Cisco :: How To Configure 1131 AP To Use WPA2 Enterprise

May 2, 2012

I have a Win2008 server set up as a radius server ( and a stand alone AP ( [code]

View 3 Replies View Related

Cisco :: 1131 - AP Group Not Working Properly

Sep 27, 2012

I have one Flex WLC 7510 using software version 7.0.220, And all APs are 1131.
I have some sites with H-Reap, where H-Reap is configured properly.
The Access Points are set with AP Group. AP Group is configured properly too.
Each AP Group was configured for one site, and they was configured with 2 SSIDs. All sites has 2 differents SSIDs. During some basic tests, in one site with 9 APs, I saw:
1. When the Access Points are registred on WLC, all APs are working fine.     All APs has your 2 SSID added on slot 0 (radio 0)

2. If I disable the link between WLC and Access Points, 7 access points delete SSIDs on your AP Groups and replace it with 16 SSIDs (SSIDs on Default Group) configured on WLC.

View 5 Replies View Related

Cisco Wireless :: How To Join The AP To WLC2500

May 16, 2013

I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.

WLC: Cisco 2500
IP Address:

View 5 Replies View Related

Cisco Wireless :: AIR-LAP Does Not Join With WLC2100

Mar 24, 2013

Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below  the error message generate:

View 2 Replies View Related

Cisco Wireless :: LAP1131AG Won't Join WLC On SRE-ISM

Jul 10, 2012

I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server ( [OK]


But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC

View 2 Replies View Related

Cisco Wireless :: AP1252 Can't Join On WLC

Apr 8, 2012

WLC software
1. first problem: AP1252 can´t join on WLC. MAC was add on mac filter properly.
170Mon Apr 9 15:37:32 2012Mesh Node '2c:3f:38:be:53:ef' failed to join controller, MAC address not in MAC filter list.171Mon Apr 9 15:37:32 2012AAA Authentication Failure for UserName:2c3f38be53e0 User Type: WLAN USER172Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 40:a6:d9:ef:87:68 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 46 7 5 4 2 1 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0173Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 8c:7b:9d:05:a0:67 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 50 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0174Mon Apr 9 15:37:30


Several APs can´t join on WLC and all are added on MAC filter, but they are showing this messages.  
2 . Second problem.:  Operational Status = UNKNOWN

Some Access Point are in UNKNOWN status. I tried but I can´t do the reboot. I can access Web config the APs using WLC, but when I applied the reset, it wasn´t working properly.

View 2 Replies View Related

Cisco Wireless :: 2504 - AP Cannot Join WLC

Jun 10, 2013

I'm new in installing WIFI, I have WLC 2504 using I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable

View 15 Replies View Related

Copyrights 2005-15, All rights reserved