Cisco Wireless :: 1131 AP12.4 JA And 5508 V7.2
Jun 4, 2013
I have some questions about this AP and it's IOS. I have some AP's 1131 and they have IOS 12.34(3g) JA I'm working with a 4402 WLC I'm going to change this WLC for one 5508 but this WLC has a different version software it has 7.2.103. My questions is I need to do any upgrade to my AP's IOS for join to the new WLC ?
I found a compatibility Matrix, in this document I guess i nedd to do some upgrade: URLs
The WGB can be any autonomous access point that supports the workgroup bridge mode and is running Cisco IOS Release 12.4(3g)JA or later releases (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later releases (on 16-MB access points). These access points include the AP1120, AP1121, AP1130, AP1231, AP1240, and AP1310. Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.
View 21 Replies
ADVERTISEMENT
Apr 25, 2012
We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.
View 6 Replies
View Related
Apr 18, 2013
I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
View 4 Replies
View Related
Jan 31, 2013
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies
View Related
Jun 15, 2012
I have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
View 4 Replies
View Related
May 20, 2012
We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example 172.25.25.4), but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is 192.168.25.4 - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.
View 9 Replies
View Related
Mar 4, 2013
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
[Code]......
View 15 Replies
View Related
Jul 31, 2012
I have WLC 4402 with software IOS 5.2.157.0 and i am planing to upgrade the sofware to the latest one (7.0.235.0)
now my question are :
1 - is that software version will support APs [AIR LAP 1131 AG-E-K] ?
2- on down load page there 2 files :
a) Cisco Unified Wireless Network Controller Boot Software 7.0 for Cisco 4400 Series Wireless LAN Controllers.
b) Cisco Unified Wireless Network Software Release 7.0 for Cisco 4400 Series Wireless LAN Controllers. which file i need to upload on my WLC 4402
View 13 Replies
View Related
Mar 3, 2010
I have an AP(1131) that keeps disassociating from the controller. It stays alive for about 10 mins then it doens't work anymore. I tired changing the AP but that didn't make a difference. I also tried changing the port on your 500 POE switch. My last effort to fix it was to put the AP on a 3550 switch with a power injector. Still no luck.
I don't understand why its doing this. I am able to connected to it and surf the internet for about 10 mins. After that It leaves the controller and just cycles through different colors.
View 18 Replies
View Related
Oct 28, 2012
I have setup a 1131 with multiple ssid's, they show up, but neither one will connect. i need 2 ssid's, one open and one protected. this is the config i have so far:
[code]....
View 8 Replies
View Related
Aug 10, 2011
Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a 5.1.151.0 in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that 5.1.151.0 dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
AP
LWAPP Static IP Configuration
IP Address 172.18.240.244
IP netmask 255.255.255.192
Default Gateway 172.18.240.193
[Code]....
View 8 Replies
View Related
Apr 21, 2011
How to shut off wireless admin access on a 1131 AP? I only want to be able to administer the device via the wired LAN. I need to shut of http, ssh, and telnet.
I haven't been able to find anything in the GUI.
How to know the CLI commands?
View 6 Replies
View Related
Jul 21, 2012
I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.
View 12 Replies
View Related
May 7, 2013
i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
View 20 Replies
View Related
Mar 22, 2012
I want to install lightweight IOS into Aironet 1131AG by using Upgrade Tool. However, some error messages appear saying:
1. ACL / Firewall might be blocking the TFTP.
2. Disable the ACL/Firewall setting for TFTP.
I don't set up any ACL because I am trying to install to the Aironet which was just initialized by using mode button. Configuration is just like followings.
Is there any possibility that the configuration block the TFTP communication ? now, ping is reachable and directly, I am connecting AP and PC with upgrade tool . and windows firewall is disable on the PC. But the upgrade tool is error. Why the TFTP communication is failed.
Building configuration...
Current configuration : 1361 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log date time msec service password-encryption!host name ap!no aaa new-mode[ code]...
View 4 Replies
View Related
Sep 8, 2011
Cisco Air 1131 AP. Having problems with Apple products. Even tried no security.
View 2 Replies
View Related
Jul 17, 2012
I configured DHCP pool on Cisco AP 1131, Laptop users are working fine and obtain IP address from AP 1131 DHCP Server, but IPad user is getting IP problem when he try to connect Cisco AP 1131.when i reboot the AP, IPad user getting IP address from 1131 AP dhcp server and access the network resource for the 2-3 hr after that IPad show "obtaining ip address from .....".
AP Detail-
AIR-AP1131AG-N-K9
c1130-k9w7-tar.124-10b.JA2
12.3(8)JEA
View 1 Replies
View Related
Dec 23, 2012
I have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.
View 3 Replies
View Related
Feb 15, 2012
I have an 1131ag AP attached to our 5508 as an OEAP over the Internet. Everything with the corporate SSIDs is working correctly, so no issue there. I was wondering if a local ssid can be configured on the AP, similar to what can be done with the OEAP600, in order to provide wireless access to the Internet only? On the WLC, on the H_REAP tab, there is a button labeled "Reset Personal SSID"
View 3 Replies
View Related
Jan 15, 2013
I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. can i convert without connecting to WLC .
View 1 Replies
View Related
Sep 28, 2011
I have the 1131 hardware manual and it is stating that this is caused by a boot loader issue or the AP did not get the IOS file from the controller. We have a Cisco 4404 controller that this AP reports to. It was one out of 30 and after a reboot it is working fine. What can i do in the future to catch this and prevent this from happening.
View 1 Replies
View Related
May 1, 2012
I have WLC 520 with software version 5.2.178. Currently we purchased Cisco AIR-LAP1131G access points and tried to join to WLC 520 but it is not joining. My question is WLC 520 will support 1131G access pont or not.?
View 1 Replies
View Related
Mar 6, 2013
I, at work, have recently deployed a very small stub network in Papua New Guinea, an office that has no more than 7/8 users. This simple network consists of:
1 x 2611xm Router
1 x 2960 24port Catalyst Switch
1 x 1131ag AP
[Code].....
View 2 Replies
View Related
Feb 29, 2012
I have several APs directly connected to a Cisco 3560 and each port is configured this way....
interface FastEthernet0/1
description Uplink To Access Point
switchport trunk encapsulation dot1q
[Code].....
The switch shows the AP under sho cdp niegh but when I go to the controller and look at AP neigh nothing shows up. I am currently running a WLC 4404 with 4.2.209 ( yes the upgrade happens tomorrow ).
why the switch shows the neigh. but not the AP when looking from the controller?
View 4 Replies
View Related
Jun 29, 2011
Can I change the untagged vlan on a 1131 to a new vlan. I need to move my management vlan from 10.1.1.1 on vlan 1 , to 172.16.0.1 on vlan 200. I attempted several configuration options including removing the vlan1 ip, changing my new vlan200 to untagged and mirroring it on the switch, and adding my new ip to vlan 1 untagged and then untagging the switch with access vlan 200 on the connected port. Nothing worked.
Below is a sample of what I changed:
interface Dot11Radio1
no ip address
no ip route-cache
[Code]....
View 1 Replies
View Related
Jan 21, 2011
I've ran into an issue that I haven't seen before. A client of mine has a WLC that manages AP's at several different sites on the East Coast. They are all connected via a multilinked T1x2 connection. One site in particular contains 7 AP's, and users at this site are unable to connect. The remaining sites have no issue at all connecting. I noticed that when users began reporting this that all AP's had failed interference profiles. Also, when I instruct a user to attempt a connection, I don't ever see their mac address come across a debug session on the controller, which I find odd. Is it possible that a neighboring business is sending deauth packets and containing my AP's?
The client is running code version 4.2.61.0.
View 2 Replies
View Related
May 2, 2012
I have a Win2008 server set up as a radius server (192.168.32.71) and a stand alone AP (192.168.201.9) [code]
View 3 Replies
View Related
Sep 27, 2012
I have one Flex WLC 7510 using software version 7.0.220, And all APs are 1131.
I have some sites with H-Reap, where H-Reap is configured properly.
The Access Points are set with AP Group. AP Group is configured properly too.
Each AP Group was configured for one site, and they was configured with 2 SSIDs. All sites has 2 differents SSIDs. During some basic tests, in one site with 9 APs, I saw:
1. When the Access Points are registred on WLC, all APs are working fine. All APs has your 2 SSID added on slot 0 (radio 0)
2. If I disable the link between WLC and Access Points, 7 access points delete SSIDs on your AP Groups and replace it with 16 SSIDs (SSIDs on Default Group) configured on WLC.
View 5 Replies
View Related
Sep 25, 2011
I have a LMS 4.1 and ive enabled Energywise on several switches.I can see them on energywise devices. they are in the same domain and most of them have IP Phones and Access Points.there are 18 IP Phones registered to a CUCM which is seen by the LMS. and ive done a user tracking and ive seen the phones registered.the access points are LAPs and CAPs (1142, 1131, 3500).
when i try to enable the Energywise End Hosts, i cant see any of the end hosts of the switches.however, when i go on CLI, and see the energwise children, i see them all.
View 2 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related
Oct 24, 2011
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies
View Related
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
