Cisco Wireless :: 1131 Ap Working With 5108 Controller But Not With 2125
Dec 23, 2012
I have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
I have a Cisco 2125 Wireless Lan Controller and I have problem with hold coverage errors and I had tri different solutions with different antenna, the resume is:The antena gain 10*0,5 Dbi(Using a 5 Dbi antenna or 10 Dbi antenna) with Tx power 1 and the antenna gain 20*0,5 Dbi (using 10Dbi antenna) with Tx power 3 the coverage is the same.
If I try the configuration 20*0,5 gain antenna and Tx power 1 the controller show me one error and the controller don't permit this configuration. Why don't permit this configuration?
I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
I have an AP(1131) that keeps disassociating from the controller. It stays alive for about 10 mins then it doens't work anymore. I tired changing the AP but that didn't make a difference. I also tried changing the port on your 500 POE switch. My last effort to fix it was to put the AP on a 3550 switch with a power injector. Still no luck.
I don't understand why its doing this. I am able to connected to it and surf the internet for about 10 mins. After that It leaves the controller and just cycles through different colors.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. can i convert without connecting to WLC .
I have several APs directly connected to a Cisco 3560 and each port is configured this way....
interface FastEthernet0/1 description Uplink To Access Point switchport trunk encapsulation dot1q
[Code].....
The switch shows the AP under sho cdp niegh but when I go to the controller and look at AP neigh nothing shows up. I am currently running a WLC 4404 with 4.2.209 ( yes the upgrade happens tomorrow ).
why the switch shows the neigh. but not the AP when looking from the controller?
I have one Flex WLC 7510 using software version 7.0.220, And all APs are 1131.
I have some sites with H-Reap, where H-Reap is configured properly.
The Access Points are set with AP Group. AP Group is configured properly too.
Each AP Group was configured for one site, and they was configured with 2 SSIDs. All sites has 2 differents SSIDs. During some basic tests, in one site with 9 APs, I saw:
1. When the Access Points are registred on WLC, all APs are working fine. All APs has your 2 SSID added on slot 0 (radio 0)
2. If I disable the link between WLC and Access Points, 7 access points delete SSIDs on your AP Groups and replace it with 16 SSIDs (SSIDs on Default Group) configured on WLC.
We will need to implement a small temporary wirelles solution where I will not have enough time to get a controller. We already have spare AIR-LAP-1042N-T-K9 that may be used (not configured in H-REAP as we use to do). If we configure these access point in local mode do they work without a controller ?
I am configuring a WLC2125 which I'll install in a customer's building to convert AP1131 to LWAPP currently it is out of the network as a lab but the problem is that I could convert an AP to LWAPP but it does not associates to the WLC, this is the log it generates:
*Apr 08 21:07:13.801: %LWAPP-3-RD_ERR9: spam_lrad.c:8375 APs 00:18:74:4b:ed:e0 country code changed from (MX ) to (US ) *Apr 08 21:07:13.800: %LWAPP-3-RD_ERR8: spam_lrad.c:8056 Country code (MX ) not configured for AP 00:18:74:4b:ed:e0
We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset work to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can see DISCOVERY request from AP and response from WLC to AP, but AP don't send JOIN to controller.
I try to make custom web-auth bundle for WLC 2125. User authentication from this custom page work fine, but any error messages about wrong login/pass not work.
Is this supported function for custom pages? If yes, could you result a working html-code?
I have WLC 2125 on version 6.0.182.0 and AP's on version 12.4(21a)JA.I also have a load more AP's (newones) 1041's with IOS version 15.2.
So i have to upgrade my WLC because the newones are not compatable with the old WLC version.What will happen to the old AP's ?I was told they will automatically update the IOS version.These AP's (oldones) are not on site, they are in a differnet LAN.
I have cisco wlc 2125 and external web autherthation was configured on it. When user disable the java script in browser cisco wlc do not redirect on my external page instead of wlc show page http://1.1.1.1/login.html with cisco logo. How can i resolve this problem? How to configure wlc redirect to external web auth site with disabled java in users browser?
I have a ACL applied on a WLAN on a 2125 controller. I cannot get the older Cisco IPSec (Version 5.0.05.0290) client to work through the ACL and through the WLAN onto it's destination. When the Cisco IPSec client is on another unrestricted WLAN, it works. I have allowed TCP/UDP 500, 4500, TCP 10000 both directions and it fails. I can see the denys counters incrementing but cannot figure out what is being blocked.
I have a Dell Studio 1537 running on Windows Vista? my computer stopped being able to connect to the internet a few days ago and a "Dell Wireless WLAN Controller closed and stopped working" (or something along those lines) box would keep on popping up. I did some reading around on the internet and decided that maybe I needed to update the "drivers" for it so I went to the Dell website and downloaded the most recent version for my Dell Wireless 1510 WLAN mini card...that didn't seem to work any after I installed it. So I went ahead and uninstalled it (I assume I must have uninstalled something I shouldn't have) and now I'm stuck at the same problem. I can't connect to the internet!In Network Connections, it continually says that "Windows cannot find any networks". In Device Manager, under Network Adapters, it doesn't list the card there, although it lists "Broadcom Netlink (TM) Gigabit Ethernet". And from some suggestions I found on the net, I tried ipconfig/all in the comand promt and it says "media disconnected".
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 120810 Rel.44064n ISP : COX
Trying to set up my Samsung ML-1430 printer using a Mac OS 10.6.8. Downloaded and installed the TP-Link_UDS_Printer_Controller. The printer controller found the printer and and it is now connected as the "Auto-Connected Printer" but it does not show anywhere to be selected so I can print to it. Tech support suggested uninstalling and reinstalling the software which I did. Still no option to print to it.
I have a 2125 WLC. I have some 1242 Access Point registered to the WLC. The problem is that the handheld connects to the WLC but sometimes it shows that it has lost wireless signal. Users say that this happens when they go from one site to another. I go to that specific site with my AirMagnet tool and it shows full signal. The customer is saying that WLC is not working with roaming properly.
I have a new brand dell inspiron 1525 laptop and everytime i boot i get a message "Dell wireless WLAN card wireless network controller stopped working and was closed.
A problem caused the application to stop working correctly.Windows will notify you if a solution is available.I use windows vista premium and dell wireless 1390 802.11g.
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example 172.25.25.4), but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is 192.168.25.4 - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048 -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
I have some questions about this AP and it's IOS. I have some AP's 1131 and they have IOS 12.34(3g) JA I'm working with a 4402 WLC I'm going to change this WLC for one 5508 but this WLC has a different version software it has 7.2.103. My questions is I need to do any upgrade to my AP's IOS for join to the new WLC ?
I found a compatibility Matrix, in this document I guess i nedd to do some upgrade: URLs
The WGB can be any autonomous access point that supports the workgroup bridge mode and is running Cisco IOS Release 12.4(3g)JA or later releases (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later releases (on 16-MB access points). These access points include the AP1120, AP1121, AP1130, AP1231, AP1240, and AP1310. Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.
I have setup a 1131 with multiple ssid's, they show up, but neither one will connect. i need 2 ssid's, one open and one protected. this is the config i have so far:
Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a 5.1.151.0 in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that 5.1.151.0 dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
AP LWAPP Static IP Configuration IP Address 172.18.240.244 IP netmask 255.255.255.192 Default Gateway 172.18.240.193 [Code]....
I regularly get this message (but not everytime) when I start up Windows Vista Home Premium 32-bit.
"Dell Wireless WLAN Card Wireless Network Controller stopped working and was closed.a problem caused the application to stop working correctly. Windows will notify you if a solution is available."
Then I get this following message:"Solution Found: Address a problem with your WLAN card.Your WLAN card has stopped working properly. This is a network adapter that allows your computer to connect to a wireless network. To find out if an updated version of your WLAN card is available, contact your device or computer manufacturer."The strange thing is even though I get this message I am still able to connect to the internet via a wireless network. So there is no problem as such it is just annoying to keep getting this message when Windows starts up.I have checked on the DELL Support website and I do have the most up-to-date driver already (Or I think I do).
How to shut off wireless admin access on a 1131 AP? I only want to be able to administer the device via the wired LAN. I need to shut of http, ssh, and telnet.
I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.
