We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset work to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can see DISCOVERY request from AP and response from WLC to AP, but AP don't send JOIN to controller.
View 2 RepliesI have a Cisco 2125 Wireless Lan Controller and I have problem with hold coverage errors and I had tri different solutions with different antenna, the resume is:The antena gain 10*0,5 Dbi(Using a 5 Dbi antenna or 10 Dbi antenna) with Tx power 1 and the antenna gain 20*0,5 Dbi (using 10Dbi antenna) with Tx power 3 the coverage is the same.
If I try the configuration 20*0,5 gain antenna and Tx power 1 the controller show me one error and the controller don't permit this configuration. Why don't permit this configuration?
how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View Relatedhow can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 12 Replies View RelatedI'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
1、the router power led's emitting light very weak ,
2、client pc cannot get ip from connected router
these error perhaps happened after a plug power jack action. Dc-dc chip is ME5513,the voltage on its pin4 is about 11.94V,and the voltage on following electrolytic capacitor is 3.3V,its seem normal.
I have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.
View 5 Replies View RelatedWe have several SF-300-48P switches, eveytime there is a power failure the switches need to reboot 2 or 3 times before they are able to route packets again.
View 1 Replies View RelatedI've got the power cut while PC was running (w7). After rebooting I'm not able to connect to the internet anymore.
In Device Manager, under Network Adapters there is a "Realtek PCIe GBE..." device properly installed. But under Other Devices there are now more entries with exclamation mark:
- Network controller
- Multimedia controller
- PCI Communication controller
etc
I tried updating the drivers, then deleting and reinstalling but no success so far. Still can't connect to the internet. The browser can see the router, at 192.168.1.1 I don't know where the problem is.
I bougth a used ASA 5505 on ebay which is experiencing this problem [url]... LEVELS or at least the described problem, if i touch the appliance while it is running it will somtimes go to this non working state as well
View 11 Replies View RelatedI have a WS-C6509-E (R7000) and am trying to implement some proactive monitoring for environmental alerts. What is the output from a Power Supply failure for the following “sh log” “sh environment alarm”.
View 1 Replies View RelatedFirmware asa805-k8 was installed and saved on an ASA5505. Upon power failure the ASA5505 reverts to an older firmware, asa724-k8. 1) Is it normal for ASA5505's to revert to older version upon power failure. 2) ASDM/web browser doesn't work using IE--username and password brings to empty screen. how to revert back to later image.
"
# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
[Code]......
We had power failure catalyst 6509 and after the device boot up ssh does not work any more below is error messages
line con 0
access-class 90 out
logging synchronous
[Code]....
Thinking back, about a month ago I updated the firmware (I can't check version at the moment). The switch has been working fine since then. Today I needed to move some power cables and the switch lost power. Now ALL of the LED lights are flashing green and I can't access the switch. I've tried setting a static IP on my laptop to 192.168.1.20, mask 255.255.255.0, and accessing the switch on 192.168.1.254, but there's no response. I've tried holding in the reset button for at least 30 seconds while the switch is powered on, AND while powering it on. None of that has worked. Also when I first power it on, the system LED flashes orange very quickly for a second or so, then all of the LEDS start flashing green.
View 5 Replies View RelatedAfter a recent power outage while my PC was in sleep mode, I don't have wired (Ethernet) connectivity.
I have new Dimension E510XP Media Center Edition, Version 2002, SP3 ver had an issue with wired connectivity on this PC after coming out of sleep mode. Of course, the power failure was unusual.
Observations:
- ipconfig /all shows that I have an IP address
- I can ping the DHCP server listed in ipconfig /all and I also can ping google.com.
- I was going to go a restore point set before the power outage. But, somehow system restore had gotten turned off. Oh, well. I did go ahead and turn system restore back on.
Things I've already tried that did not solve the issue:
- Reboot
- Uninstall/reinstall the network adapter driver. Device Manager says the network adapter card is working properly.
- Looked for an updated network adapter driver on Dell's website. Turns out that I have the latest driver already.
- Followed many of the steps from Microsoft at [URL]
- Checked McAfee Security Center firewall permissions list to see if something got changed. Everything looked okay. Also disabled the firewall just to be sure,
- Disabled SafeEyes internet filter.
- Reset the router. Also swapped router ports with a known good PC. The known good PC still had connectivity, the affected PC (the E510) did not.
I have a switch 3560v2 with an IOS 12.2(50) SE1.All the lights ON and console error message below:POST: inline power post failed for port 0 up to port 15.Then, the system hanged and all lights (indicator) ON.
View 5 Replies View RelatedMissing local area connection icon in network connection after power failure?
View 1 Replies View RelatedI am configuring a WLC2125 which I'll install in a customer's building to convert AP1131 to LWAPP currently it is out of the network as a lab but the problem is that I could convert an AP to LWAPP but it does not associates to the WLC, this is the log it generates:
*Apr 08 21:07:13.801: %LWAPP-3-RD_ERR9: spam_lrad.c:8375 APs 00:18:74:4b:ed:e0 country code changed from (MX ) to (US )
*Apr 08 21:07:13.800: %LWAPP-3-RD_ERR8: spam_lrad.c:8056 Country code (MX ) not configured for AP 00:18:74:4b:ed:e0
[Code].....
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
View 2 Replies View RelatedI try to make custom web-auth bundle for WLC 2125. User authentication from this custom page work fine, but any error messages about wrong login/pass not work.
Is this supported function for custom pages? If yes, could you result a working html-code?
I have WLC 2125 on version 6.0.182.0 and AP's on version 12.4(21a)JA.I also have a load more AP's (newones) 1041's with IOS version 15.2.
So i have to upgrade my WLC because the newones are not compatable with the old WLC version.What will happen to the old AP's ?I was told they will automatically update the IOS version.These AP's (oldones) are not on site, they are in a differnet LAN.
I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies View RelatedI have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.
View 3 Replies View RelatedI have cisco wlc 2125 and external web autherthation was configured on it. When user disable the java script in browser cisco wlc do not redirect on my external page instead of wlc show page http://1.1.1.1/login.html with cisco logo. How can i resolve this problem? How to configure wlc redirect to external web auth site with disabled java in users browser?
View 3 Replies View RelatedI have a ACL applied on a WLAN on a 2125 controller. I cannot get the older Cisco IPSec (Version 5.0.05.0290) client to work through the ACL and through the WLAN onto it's destination. When the Cisco IPSec client is on another unrestricted WLAN, it works. I have allowed TCP/UDP 500, 4500, TCP 10000 both directions and it fails. I can see the denys counters incrementing but cannot figure out what is being blocked.
View 1 Replies View RelatedI have a 2125 WLC. I have some 1242 Access Point registered to the WLC. The problem is that the handheld connects to the WLC but sometimes it shows that it has lost wireless signal. Users say that this happens when they go from one site to another. I go to that specific site with my AirMagnet tool and it shows full signal. The customer is saying that WLC is not working with roaming properly.
The handheld is a Dolphin 7900.
I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
I'm having problem joining a AP802 access-point in a Cisco 887VAM-W router to a WLC2125 running 7.0.116.0. I get the following messages pasted below from the AP console. The AP connects to the WLC over a EZVpn tunnel with a ASA on the other end, and can't see any error messages there. [code]
View 5 Replies View RelatedI am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
I am quite new to WCS and preparing a demo for a client. I am also using WLC2125 with LAP1252s for this setup. Is it possible to modify the shape of the heatmaps of the APs? I know how to regulate TX power of the radios and all works great but how can I controll RF leakage outside the perimiter of the building? Is it possible to controll the RF so that it will not be going outside and same time giving a good coverage inside?
View 1 Replies View RelatedCurrent environment is Cisco 2125 WLC managing ~12 3502E AP's for a single location. Client is looking to provide HA for the single 2125 WLC. With the 2125 now EO-Sale is it possible to go with one additional 2504 WLC and leverage the existing 2125 or would it require going with just (2) 2504's?
View 1 Replies View RelatedI have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.
I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0