Cisco Wireless :: 2125 - WLC Does Not Adopt APs
Aug 4, 2011
I am configuring a WLC2125 which I'll install in a customer's building to convert AP1131 to LWAPP currently it is out of the network as a lab but the problem is that I could convert an AP to LWAPP but it does not associates to the WLC, this is the log it generates:
*Apr 08 21:07:13.801: %LWAPP-3-RD_ERR9: spam_lrad.c:8375 APs 00:18:74:4b:ed:e0 country code changed from (MX ) to (US )
*Apr 08 21:07:13.800: %LWAPP-3-RD_ERR8: spam_lrad.c:8056 Country code (MX ) not configured for AP 00:18:74:4b:ed:e0
[Code].....
View 4 Replies
ADVERTISEMENT
Sep 28, 2010
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
View 2 Replies
View Related
Jan 13, 2013
We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset work to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can see DISCOVERY request from AP and response from WLC to AP, but AP don't send JOIN to controller.
View 2 Replies
View Related
Feb 16, 2012
I try to make custom web-auth bundle for WLC 2125. User authentication from this custom page work fine, but any error messages about wrong login/pass not work.
Is this supported function for custom pages? If yes, could you result a working html-code?
View 3 Replies
View Related
Aug 29, 2011
I have a Cisco 2125 Wireless Lan Controller and I have problem with hold coverage errors and I had tri different solutions with different antenna, the resume is:The antena gain 10*0,5 Dbi(Using a 5 Dbi antenna or 10 Dbi antenna) with Tx power 1 and the antenna gain 20*0,5 Dbi (using 10Dbi antenna) with Tx power 3 the coverage is the same.
If I try the configuration 20*0,5 gain antenna and Tx power 1 the controller show me one error and the controller don't permit this configuration. Why don't permit this configuration?
View 3 Replies
View Related
Apr 1, 2013
I have WLC 2125 on version 6.0.182.0 and AP's on version 12.4(21a)JA.I also have a load more AP's (newones) 1041's with IOS version 15.2.
So i have to upgrade my WLC because the newones are not compatable with the old WLC version.What will happen to the old AP's ?I was told they will automatically update the IOS version.These AP's (oldones) are not on site, they are in a differnet LAN.
View 4 Replies
View Related
May 29, 2012
I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies
View Related
Dec 23, 2012
I have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.
View 3 Replies
View Related
Jul 21, 2012
I have cisco wlc 2125 and external web autherthation was configured on it. When user disable the java script in browser cisco wlc do not redirect on my external page instead of wlc show page http://1.1.1.1/login.html with cisco logo. How can i resolve this problem? How to configure wlc redirect to external web auth site with disabled java in users browser?
View 3 Replies
View Related
Dec 6, 2012
I have a ACL applied on a WLAN on a 2125 controller. I cannot get the older Cisco IPSec (Version 5.0.05.0290) client to work through the ACL and through the WLAN onto it's destination. When the Cisco IPSec client is on another unrestricted WLAN, it works. I have allowed TCP/UDP 500, 4500, TCP 10000 both directions and it fails. I can see the denys counters incrementing but cannot figure out what is being blocked.
View 1 Replies
View Related
Sep 15, 2010
I have a 2125 WLC. I have some 1242 Access Point registered to the WLC. The problem is that the handheld connects to the WLC but sometimes it shows that it has lost wireless signal. Users say that this happens when they go from one site to another. I go to that specific site with my AirMagnet tool and it shows full signal. The customer is saying that WLC is not working with roaming properly.
The handheld is a Dolphin 7900.
View 4 Replies
View Related
Dec 3, 2011
I'm having problem joining a AP802 access-point in a Cisco 887VAM-W router to a WLC2125 running 7.0.116.0. I get the following messages pasted below from the AP console. The AP connects to the WLC over a EZVpn tunnel with a ASA on the other end, and can't see any error messages there. [code]
View 5 Replies
View Related
Dec 6, 2012
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
View 1 Replies
View Related
Mar 20, 2011
I am quite new to WCS and preparing a demo for a client. I am also using WLC2125 with LAP1252s for this setup. Is it possible to modify the shape of the heatmaps of the APs? I know how to regulate TX power of the radios and all works great but how can I controll RF leakage outside the perimiter of the building? Is it possible to controll the RF so that it will not be going outside and same time giving a good coverage inside?
View 1 Replies
View Related
Oct 28, 2012
Current environment is Cisco 2125 WLC managing ~12 3502E AP's for a single location. Client is looking to provide HA for the single 2125 WLC. With the 2125 now EO-Sale is it possible to go with one additional 2504 WLC and leverage the existing 2125 or would it require going with just (2) 2504's?
View 1 Replies
View Related
Aug 27, 2012
I have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.
View 2 Replies
View Related
Oct 29, 2012
I have a Netgear WNR3500L wireless router. I assume it's v1 because on the back it doesn't have "v" anything. Firmware version V1.2.2.44_35.0.53NA.When I connect using g I get 22+Mbps download speed. When I connect using n I get 10 Mbps. I've tried using both WPA2 only (laptop reports 130 Mbps connection I believe) as well as the combo WPA+WPA2 (laptop reports connection of 117 Mbps).Broadband download results don't change - they stay at the 10 Mbps level. I've fiddled with some of the settings on my laptop's wireless card - but the results are the same.For now I'm just trying to figure out where I should focus my investigation and fiddling efforts - on the laptop or on the router.
View 5 Replies
View Related
Jan 6, 2013
i have a Netgear N600 Wireless ADSL2+ router on wireless a/b/g/n dual band and all that but what i want to know is will i get better performance if i use a WirelessN card over G on a 10 - 15mb/s connection gaming wise and will it b a great increase over the G causeif its not a HUGE increase then i wont waste my money on a newer card?
View 3 Replies
View Related
Jun 3, 2012
My Acer Aspire 5610Z laptop will automatically connect to public hotspot wireless network but when I attempt to connect to a wireless network at home, set up using a Netgear modem, I only ever get 'local' internet connection only. My wife's HP laptop has no problem making the home wireless connection.
View 6 Replies
View Related
Jan 31, 2013
I am running windows vista and have installed the software and windows sees the adapter and states it is working but when it searches for available networks it can't find any. How can I download the driver and install it?
View 1 Replies
View Related
Oct 19, 2011
I have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related
Oct 24, 2011
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies
View Related
Apr 30, 2012
We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
View 2 Replies
View Related
Jan 7, 2010
i am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies
View Related
Jan 19, 2011
Due to lack of wires we decided to extend our network by using WET546 bridge by linksys. Ideally we looking to create topology like this:
(Computer)--eth--(WET546)---wireless----(AP/WLC2100)---(router)---(Internet)
WET546 successfully authenticates and looks pretty healthy on controller (see below) , however neither of computers plugged to WET546 was unable to obtain ip address from dhcp server , nor working with static ip. I was under impression what it might be related to some default policies on WLC2100. Logs (warning) on WLC2100 looks clean.
View 8 Replies
View Related
Sep 16, 2012
This is the first time I am trying my hands on wireless gears. I have 2500 WLC and 1142 AP (which I converted from Standalone to LAP).I have a layer 3 POE switch where i am using port 1 for the WLC which is a trunk port.
Port 2 is for the AP using access vlan 111
Port 3 is trunk port going to a router where i am running dhcp server for the VLANs which are as follow:
VLAN 110 -Corp Wireless (10.1.110.0/24)
VLAN 111 - AP-Mgmt (10.1.111.0/24)
VLAN 999 - Guest (10.1.101.0/24)
I wanted to block the traffic from the Guest VLAN 999 but when i apply the ACL on the Guest Interface created on the WLC, I dont see any pings going across and neither I see any hit counts on the deny statement as if the ACL is never applied.
View 4 Replies
View Related
Aug 10, 2010
Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies
View Related
Feb 3, 2013
I just read that starting from version 7.4, the 2500 controller can be used to terminate guest anchor tunnels. have a question regarding the performance of the internal DHCP server when used in guest environments.
View 1 Replies
View Related
Sep 18, 2012
We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
View 3 Replies
View Related
Jun 10, 2012
Android users can connect to our hospital guest wireless but will not have connectivity. Our wireless infrastructure is WISM based with 2 controllers on 6509 platform. We have a mixed environment of 1231, 1252 & 3502 series APs.
Had issue connecting just Android devices? All other devices connect fine.
View 5 Replies
View Related
Jul 4, 2011
I have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it. There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
WLC (LEAP with local users) -----> LAP ----> Repeater AP
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.
View 1 Replies
View Related
