I'm having problem joining a AP802 access-point in a Cisco 887VAM-W router to a WLC2125 running 7.0.116.0. I get the following messages pasted below from the AP console. The AP connects to the WLC over a EZVpn tunnel with a ASA on the other end, and can't see any error messages there. [code]
View 5 RepliesI am configuring a WLC2125 which I'll install in a customer's building to convert AP1131 to LWAPP currently it is out of the network as a lab but the problem is that I could convert an AP to LWAPP but it does not associates to the WLC, this is the log it generates:
*Apr 08 21:07:13.801: %LWAPP-3-RD_ERR9: spam_lrad.c:8375 APs 00:18:74:4b:ed:e0 country code changed from (MX ) to (US )
*Apr 08 21:07:13.800: %LWAPP-3-RD_ERR8: spam_lrad.c:8056 Country code (MX ) not configured for AP 00:18:74:4b:ed:e0
[Code].....
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
View 2 Replies View RelatedI am quite new to WCS and preparing a demo for a client. I am also using WLC2125 with LAP1252s for this setup. Is it possible to modify the shape of the heatmaps of the APs? I know how to regulate TX power of the radios and all works great but how can I controll RF leakage outside the perimiter of the building? Is it possible to controll the RF so that it will not be going outside and same time giving a good coverage inside?
View 1 Replies View RelatedCurrent environment is Cisco 2125 WLC managing ~12 3502E AP's for a single location. Client is looking to provide HA for the single 2125 WLC. With the 2125 now EO-Sale is it possible to go with one additional 2504 WLC and leverage the existing 2125 or would it require going with just (2) 2504's?
View 1 Replies View RelatedWe have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset work to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can see DISCOVERY request from AP and response from WLC to AP, but AP don't send JOIN to controller.
View 2 Replies View RelatedI try to make custom web-auth bundle for WLC 2125. User authentication from this custom page work fine, but any error messages about wrong login/pass not work.
Is this supported function for custom pages? If yes, could you result a working html-code?
I have a Cisco 2125 Wireless Lan Controller and I have problem with hold coverage errors and I had tri different solutions with different antenna, the resume is:The antena gain 10*0,5 Dbi(Using a 5 Dbi antenna or 10 Dbi antenna) with Tx power 1 and the antenna gain 20*0,5 Dbi (using 10Dbi antenna) with Tx power 3 the coverage is the same.
If I try the configuration 20*0,5 gain antenna and Tx power 1 the controller show me one error and the controller don't permit this configuration. Why don't permit this configuration?
I have WLC 2125 on version 6.0.182.0 and AP's on version 12.4(21a)JA.I also have a load more AP's (newones) 1041's with IOS version 15.2.
So i have to upgrade my WLC because the newones are not compatable with the old WLC version.What will happen to the old AP's ?I was told they will automatically update the IOS version.These AP's (oldones) are not on site, they are in a differnet LAN.
I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies View RelatedI have this issue regarding the 1131 Access Points. These access points were fat access points from the factory and were applied with LAP ios so that they can join our controller. We have 2 controllers 5108 for Internal network office use and a seperate 2125 for Guest internet both these are physically seperate networks. These AP's have been working fine since say like 8-9 months and suddenly they started giving problems. The status light keeps changing colour and the AP does not join the controller 2125. Whenever i am connecting this ap to our internal network it joins the controller 5508 and works fine but somehow does not register with our 2125 guest controller. This issue is being faced by one of our client. Could this be an issue due to the ap being loaded with lap ios or does it have anything to do with the different software version fo the controllers as i could not find any things regarding this.
View 3 Replies View RelatedI have cisco wlc 2125 and external web autherthation was configured on it. When user disable the java script in browser cisco wlc do not redirect on my external page instead of wlc show page http://1.1.1.1/login.html with cisco logo. How can i resolve this problem? How to configure wlc redirect to external web auth site with disabled java in users browser?
View 3 Replies View RelatedI have a ACL applied on a WLAN on a 2125 controller. I cannot get the older Cisco IPSec (Version 5.0.05.0290) client to work through the ACL and through the WLAN onto it's destination. When the Cisco IPSec client is on another unrestricted WLAN, it works. I have allowed TCP/UDP 500, 4500, TCP 10000 both directions and it fails. I can see the denys counters incrementing but cannot figure out what is being blocked.
View 1 Replies View RelatedI have a 2125 WLC. I have some 1242 Access Point registered to the WLC. The problem is that the handheld connects to the WLC but sometimes it shows that it has lost wireless signal. Users say that this happens when they go from one site to another. I go to that specific site with my AirMagnet tool and it shows full signal. The customer is saying that WLC is not working with roaming properly.
The handheld is a Dolphin 7900.
I have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.
Customer has got a 2 x 1552AP that wont join a WLC.
This is the debugs from the WLC. Customer cant console to AP to capture as its up in the roof so not easily accessible. why the AP wont join? Date/Time are fine on the WLC as is the region.
*spamReceiveTask: Jun 28 13:45:26.612: 2c:3f:38:be:23:c0 DTLS connection not found, creating new connection for 172:16:2:1 (57918) 172:16:0:1 (5246)
*spamReceiveTask: Jun 28 13:45:27.243: 2c:3f:38:be:23:c0 DTLS Session established server (172.16.0.1:5246), client (172.16.2.1:57918)
[Code]....
There are a total of 25 Cisco 3502 APs installed. 24 APs were discovered except for 1 AP. I run SH CDP NE on the switch and the AP was discovered by the switch but it does not have an IP address. On the output of the SH CDP NE DE, I noticed that on the AP that is not joining, the Platform is "cisco AIR-SAP3502E-E-K9" while the APs that joined the WLC, the Platform is "cisco AIR-CAP3502E-E-K9". The software versions are also different but this could be because the WLC already upgraded the IOS when the APs joined.Why is the Platform "SAP3502E" for the AP that did not join.
View 9 Replies View RelatedI had problems joining a 1131AG AP to a "new" 5508 WLC with 7.4.100.0 running. This AP has been connected to a, for me unknown controller for years. Now the customer wants to move this AP to a newer 5508 controller with 7.4.100.0 We [URL] could not get this AP to the controller connected. Now I have this AP on my desk. I have a 5508 (7.4.100.0) as well. I connected the AP to the same network as the WLC Management -> AP did not connect, tried to download the "new" IOS but didn't seem to work, same as already in the old tread. So I tried to login to the AP, but it seemed to have a for me unknown Account / Password.
-> I did a reset of the AP by pressing the mode button (about 2-3 sec.) during Power on (not connected to the network). Now I could log on to the AP. I deleted six crashinfos and connected the AP back to the network.
Now the AP joined the controller.
Does a "unknown" Password prevent the AP to join to a other WLC?
The AP hat 15740928 bytes total (6409728 bytes free) space on the Flash: was this enough for the new image? 15740928 bytes total (7798272 bytes free) after deleting the crashinfos
The customer has more AP's that has to join the new controller, would be nice that we don't have to reset all APs.
After a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
For some reason some AP will not join the WLC. (WISMII)I have several hundrede AP online, but still a few offline
This fails:
FRH-R06-L226-UX-G#sh cdp nei gi2/0/41 detail
-------------------------
Device ID: AP5057.a8a1.c632
Entry address(es):
[Code]...
recently migrated APs from a 4400 to 5508 which had the 7.4 code and encountered an issue that I haven't see before, in short the APs would never join the 5508 even when the selction rules said it should.The AP would get a discovery response from both controllers and even though the 4400 had 98 APs attached and the 5508 just 1 and a factory reset was made on the AP, it would always join the 4400.
A packet capture showed that the first CAPWAP address from the 5508 was always an IPv6 whilst the 4400 always sent IPv4 CAPWAP control adressess, disabling the global IPv6 option on the 5508 ensured that the the first CAPWAP control address was now an IPv4 and the AP then happily joined the controller, IPv6 addresses were still showing up in the discovery responses but since it was no longer the first one in the packet the AP didn't mind.
I cannot join domain it saying that "Computer name changes", A domain controller for the domain MyDomain could not be contacted.”. We have domain and workgroup, Actually first its already joined the domain, but I want to map the sharedrive inside the workgroup but I cannot map. Then I change to join workgroup. After I boot up I cannot log in with that user, I log in with administrator and the user is dissappear in the "User Account", but the profile inside document and setting still left surprise. I don't know why Now I create one more user, it can map to share drive also share folder. also can see all other network computer. But only left one is I cannot join the domain. I need this one because of we don't let our user using as administrator account. Before I testing this one I should backup, but now the time
View 2 Replies View RelatedI am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
We've just replaced some 1240 LAPs with 20 x 3502i.
Seem to have a problem, most of the 14 * 3502i have regersted on the network and working, 6 arent connecting and log below. I've replaced one of the AP with a differnt one, same model and batch and this works.
WISMs on 7.0.98.0
Scirpt
*Mar 1 00:15:16.015: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
i have 1240 series access points which is not joining controller 5500 series. [code]
View 12 Replies View Relatedthis is what happens when I try to join an acs 5.3 to the domain. On two other acs appliances, it works.
View 1 Replies View Relatedinfo regarding my LAP521 access points that are refusing to join the WLC4402-12.This is my first lightweight access point implementation and I have 3 LAP521's and 1 AIR-CAP3502I-E-K9 access points on my network.They are meant to pick up ip address from external dhcp server and then join the WLC but only the 3502i joins successfuly while the 521's get dhcp address but do not join the WLC. From the logs, I can see that the WLC is discovered by the 521's and even get a response message from the controller but they are still unable to join as shown in the screenshot below.My WLC is running software version 7.0.230.0 and the 521's are running an lwapp image version 4.2.61.8. [code]
View 3 Replies View RelatedI am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
View 3 Replies View RelatedI have been having some issues with an ACS express joining a domain. This device previously had joined and after a weekend we received a notice that users were not authenticating to the domain. This in turn let us to find out the the device was unable to join the domain. Further research led us to find that the account the device was using to join the domain had been disabled. However, after re-enabling the account we would only recieve domain timeouts when tried to join. I opened a case with cisco and we have tried everything under the sun to no avail. I can ping the AD server (name & ip) from the ACS express. Cisco apply a root patch that allowed us to create hosts file entries on the device. I checked the system time and made sure it was within 5 minutes of the Domain controller time. In the logs of the ACS express the only thing I can really find is:
-"Checking remote join status: SMB connectivity failed"
-"Timeout reached in getting AD Diag info"
"acsxp/server Warning Server 0 is DisconnectedMode, IOException for reason, ipc socket connect; No such file or directory:
Recently we re-imaged the ACS and tried to join the domain without the old config on it and just received the same error. I reloaded the backup after that which also resulted in no change. I am starting to think that there is more of a domain issue rather than networking but am having issues finding a way to prove this via the logs. The are other ACS's configured in the network and the settings on this device match the settings on the other device in the network which are working correctly.
I am performing a new install of a WLC 5760 and 3602i APs. I have limited experience in setting up WLCs. I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides: url...
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did). I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC. I have highlighted lines that I think are relevant. I have attempted to find the answer on my own by searching the Internet for these phrases. [code]
I have a couple 3600s that don't want to join. One i and one e that are both doing the something. It is able to find the controller via layer 3 discovery but it is acting like it is a mesh AP when it tries to join the controller.
From the 2500 controller (running 7.2)
*spamApTask2: May 13 12:03:05.272: f0:f7:55:ae:xx:xx Mesh AP username f0f755aexx xx.
*spamApTask2: May 13 12:03:10.739: f0:f7:55:ae:xx:xx spamProcessJoinRequest : RA
P, Check MAC filter
From the 3602i
flash:/mesh_start_cfg.txt: No such file or directory. The filesystem containing the variables may not be initialized yet.
I should note that 3500 APs are able to join this controller. The field guy is going to try to add the MAC address to the filter list when he gets back out on site to see if it allows it to join.
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
[code] ......