Cisco Wireless :: AP1131AG Now Joining WLC?
Apr 17, 2013
I had problems joining a 1131AG AP to a "new" 5508 WLC with 7.4.100.0 running. This AP has been connected to a, for me unknown controller for years. Now the customer wants to move this AP to a newer 5508 controller with 7.4.100.0 We [URL] could not get this AP to the controller connected. Now I have this AP on my desk. I have a 5508 (7.4.100.0) as well. I connected the AP to the same network as the WLC Management -> AP did not connect, tried to download the "new" IOS but didn't seem to work, same as already in the old tread. So I tried to login to the AP, but it seemed to have a for me unknown Account / Password.
-> I did a reset of the AP by pressing the mode button (about 2-3 sec.) during Power on (not connected to the network). Now I could log on to the AP. I deleted six crashinfos and connected the AP back to the network.
Now the AP joined the controller.
Does a "unknown" Password prevent the AP to join to a other WLC?
The AP hat 15740928 bytes total (6409728 bytes free) space on the Flash: was this enough for the new image? 15740928 bytes total (7798272 bytes free) after deleting the crashinfos
The customer has more AP's that has to join the new controller, would be nice that we don't have to reset all APs.
View 3 Replies
ADVERTISEMENT
Aug 19, 2012
Today I want to build a wireless bridge using AIR-AP1131AG (running WLC) and TP-LINK wireless router. The result is failed. May I know AIR-AP1131AG is support bridging the wireless connection with other vendor's access point or not?
In the TP-Link I already match its SSID, Channel and put the mac-address of the AIR-AP1131AG. In the WLC I already see too TP-LINK mac-address is already become a client.
View 6 Replies
View Related
Oct 15, 2012
I have question about compatibility. I had set up two Cisco AP AIR-AP1131AG-E-KP. They are set under one SSID whith clients roaming between them. I want to add one or two new APs. I would like to use AIR-AP1142N-E-K9. Are they compatible? Are there any issuess using these two types together?
View 2 Replies
View Related
Jul 5, 2011
I have a Brand new AP that was bought for a site which has a controller, however it was never installed. I was wondering can you downgrade this AP to make it work in stand alone mode as a normal AP?
View 1 Replies
View Related
Jan 6, 2010
my customer has a very basic LAN+WLAN configuration:
- 1 switch (not Cisco)
- 1 DSL router which is the default gateway (not Cisco)
- 2 Wi-Fi Access Points (Cisco AIR-AP1131AG-E-K9)
If he tries to establish a PPTP VPN when he is connected to the wired LAN, it works but when he tries the same from the wireless LAN it doesn't work. He says he'd tested it with Windows Firewall disabled. Is there any configuration command that can enable/disable PPTP VPN traffic pass through a Wi-Fi connection? I've never seen something like this and I use PPTP VPNs over a Wi-Fi connection every day without any particular configuration on the access point.
Here's the APs config:
hostname ...!enable secret ...!aaa new-model!!aaa authentication login default local!aaa session-id common!!dot11 syslog!dot11 ssid ... authentication open authentication key-management wpa version 2 guest-mode infrastructure-ssid wpa-psk ascii ...!power inline negotiation prestandard source!!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache !
[Code] .....
View 14 Replies
View Related
Jul 23, 2012
I tried to change the default password Cisco to other by command line but the password cannot work out.
The command line I used are as below :
AP#conf tEnter configuration commands, one per line. End with CNTL/Z.AP(config)#enable passAP(config)#enable password 4dMINO123 ?LINE <cr>
[Code].....
View 10 Replies
View Related
Dec 8, 2010
I am currently working on a project where I need to design a complete wireless solution for a huge building. I performed the wireless rf survey by configuring the wap's to broadcast a SSID and walked around gathering rf coverage data. When configuring the test WAP's i did not join them to a lan controller ( AIR-WLC4402-50-K9 ) but simply created a static ip and ssid to broadcast but modified the internal antenna gain to +128 to change the direction of the broadcast. There are two other ap's already joined to the lan controller on a guest network (configured by another contractor) but when I go into the lan controller web gui I do not see anywhere that allows me to modify antenna gain on the individual WAPs. Also, once the waps join the lan controller they dont seem to be accessible via web. How I can I modify gain per wap?
View 14 Replies
View Related
Sep 20, 2012
my hardware set-up : 2x AP 1100 series, 2x AP1131AG (not connected to a Cisco Switch)...all with the latest Cisco iOS
What i want to do is connect these APs and broadcast the same SSID (e.g Aironet and NOT Aironet1,Aironet2..etc). Doing that, a user with a laptop can roam between these APs and won't have to re-enter the password of the SSID every time he changes AP. I would also like the encryption to be with a 128bit password key. From what i have read, i need a local authenticator to do what (Something called Local Radius Server).
View 11 Replies
View Related
Jan 10, 2011
We have a site running 2 1131AG access points on different floors with the same SSID.There have been issues with connections dropping over the last 2-3 months to some newer laptops and iphones that have been introduced to the network. It is almost totally intermittent and after updating the IOS and laptop drivers where possible, there is a still a problem that wont go away.I have some example logging from both AP's when this happens (apologies for the date/time differences, however the events are all sequential)
View 5 Replies
View Related
Jul 1, 2012
Customer has got a 2 x 1552AP that wont join a WLC.
This is the debugs from the WLC. Customer cant console to AP to capture as its up in the roof so not easily accessible. why the AP wont join? Date/Time are fine on the WLC as is the region.
*spamReceiveTask: Jun 28 13:45:26.612: 2c:3f:38:be:23:c0 DTLS connection not found, creating new connection for 172:16:2:1 (57918) 172:16:0:1 (5246)
*spamReceiveTask: Jun 28 13:45:27.243: 2c:3f:38:be:23:c0 DTLS Session established server (172.16.0.1:5246), client (172.16.2.1:57918)
[Code]....
View 2 Replies
View Related
May 12, 2012
There are a total of 25 Cisco 3502 APs installed. 24 APs were discovered except for 1 AP. I run SH CDP NE on the switch and the AP was discovered by the switch but it does not have an IP address. On the output of the SH CDP NE DE, I noticed that on the AP that is not joining, the Platform is "cisco AIR-SAP3502E-E-K9" while the APs that joined the WLC, the Platform is "cisco AIR-CAP3502E-E-K9". The software versions are also different but this could be because the WLC already upgraded the IOS when the APs joined.Why is the Platform "SAP3502E" for the AP that did not join.
View 9 Replies
View Related
Mar 19, 2012
After a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
View 1 Replies
View Related
Apr 8, 2013
For some reason some AP will not join the WLC. (WISMII)I have several hundrede AP online, but still a few offline
This fails:
FRH-R06-L226-UX-G#sh cdp nei gi2/0/41 detail
-------------------------
Device ID: AP5057.a8a1.c632
Entry address(es):
[Code]...
View 3 Replies
View Related
Dec 14, 2011
We've just replaced some 1240 LAPs with 20 x 3502i.
Seem to have a problem, most of the 14 * 3502i have regersted on the network and working, 6 arent connecting and log below. I've replaced one of the AP with a differnt one, same model and batch and this works.
WISMs on 7.0.98.0
Scirpt
*Mar 1 00:15:16.015: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
View 11 Replies
View Related
Apr 2, 2013
My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
View 22 Replies
View Related
May 9, 2012
i have 1240 series access points which is not joining controller 5500 series. [code]
View 12 Replies
View Related
Oct 1, 2012
info regarding my LAP521 access points that are refusing to join the WLC4402-12.This is my first lightweight access point implementation and I have 3 LAP521's and 1 AIR-CAP3502I-E-K9 access points on my network.They are meant to pick up ip address from external dhcp server and then join the WLC but only the 3502i joins successfuly while the 521's get dhcp address but do not join the WLC. From the logs, I can see that the WLC is discovered by the 521's and even get a response message from the controller but they are still unable to join as shown in the screenshot below.My WLC is running software version 7.0.230.0 and the 521's are running an lwapp image version 4.2.61.8. [code]
View 3 Replies
View Related
Aug 7, 2011
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
View 3 Replies
View Related
Jun 13, 2013
I am performing a new install of a WLC 5760 and 3602i APs. I have limited experience in setting up WLCs. I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides: url...
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did). I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC. I have highlighted lines that I think are relevant. I have attempted to find the answer on my own by searching the Internet for these phrases. [code]
View 1 Replies
View Related
Jul 28, 2011
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
[code] ......
View 5 Replies
View Related
May 12, 2013
A customer of mine has a centralized 2504 WLC with 7.2 code running. They have 1142N APs deployed locally as well as in remote sites (3) in FlexConnect mode. For no apparent reason last Thursday all the remote APs disassociated with the controller and could not rejoin. All the local APs remained up and unaffected.No changes to the WLAN, LAN, Firewall or MPLS WAN occured to cause this.The customer opened a TAC case and their determination was that ports 5246-5247 were not getting thru. When the customer engaged me this morning I had him run a packet capture on the Sonicwall firewall to prove out if the CAPWAP signals were leaving and returning across the WAN. Sure enough we can see this bi-directional traffic (pic attached). Also, I had the MPLS provider run a trace at the far end and they see the same traffic leave the remote site. And then an odd thing happened; one of the APs at one of the remote sites all of a sudden Joined the controller. So I tried rebooting the AP that is located in the same office, and it fails to Join. When I look on the controller under AP Join statistics, the last activity shows the controller receiving a Discovery Request and response is sent, but no further Config Request and response or Join Request and response.
View 8 Replies
View Related
Nov 5, 2012
We have 3 5508 WLCs (A, B, & C) and several LAPs (1140, 3500, 3600). The APs learn the controllers IP addresses through DHCP Option 43. When we setup a new site we put the IP address of the controller we want the AP to join first. Lately, I've noticed that regardless of which WLC IP I put first when I setup Option 43 the LAPs are always joining a particular controller.
View 6 Replies
View Related
Jun 17, 2012
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty registering the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch. A bad update was not allowing the access points to get their correct firmware.
View 7 Replies
View Related
Mar 6, 2012
LAP join process: 70:ca:9b:25:5b:9d -> AP MAC10.10.1.30 -> DNS
View 8 Replies
View Related
Dec 11, 2012
I have some remote 1142s that I converted to LAP last night. They are not joing a WLC, but I they are online and I can ping them. Telnet or SSH is disabled by default (WHY???). What can I do to figure out why these access points are not joining the controller?
View 17 Replies
View Related
Jul 6, 2012
I am trying to configure new 5508wireless controller, AP 1042N model access points are able to receive DHCP IP address from Controller, but not able to join them.
View 11 Replies
View Related
Dec 6, 2012
I am tryign to join my first AP to the 5508 and am gettign this error int he logs.
*Dec 07 10:42:31.067: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an ARP entry for 0:0.0.0 to the network processor. entry does not exist
The management Interface is on the the same vlan as the AP , both untagged ports. the AP gets an ip address from my dhcp server.
View 10 Replies
View Related
Mar 15, 2013
I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies
View Related
Mar 3, 2013
I have new 1600 series Access Points. I am trying to join those APs on controller but unable to join.
After doing config reset using mode button, I was able to join only. Please find the logs or error messages below:
*Mar 4 18:53:13.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.2.241.50:5246
*Mar 4 18:53:14.063: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 4 18:53:14.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 4 18:53:14.123: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
[Code] ....
View 6 Replies
View Related
Aug 27, 2011
I am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.
*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...
View 10 Replies
View Related
Mar 7, 2012
i have a problem with our new 5508 wireless controller (7.0.116.0).
Port 1 is the system default "management" (Port 2 is backup). Dynamic AP Management is disabled. Port 3 is a new dynamic interface "ap-manager 2" with Dynamic AP Management enabled and has a ip in a seperated VLAN which is not routed.
When i am connecting the AP (1260 series) to the "ap-manager 2" interface, then it will not join and i get an error message on the WLC:
*spamApTask1: Mar 05 14:52:12.783: %CAPWAP- -DISC_INTF_ERR1:capwap_ac_sm.c:1453 Ignoring discovery request received on non-managementinterface (3) from AP
When i am connecting the AP to the "management2 interface, then it is working fine. But i don't want the APs in the Management LAN. I want them in the separated no routed LAN explicit for the APs.
View 5 Replies
View Related
Nov 1, 2012
Got a bit of a quandary with joining new access points to our 5500 series W LAN Controller. It looks like the LAP is initially able to see the W LAN controller, but after that things go sideways. The LAP is pulling a valid IP address from DHCP, and the W LAN Controller is able to ping it.
In the controller's AP Join Statistics we get this:
Last AP Message Decryption Failure
Last AP Connection Failure -Timed out while waiting for ECHO repsonse from the AP
Last AP Disconnect Reason
[code]...
View 7 Replies
View Related
Mar 13, 2013
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
View 6 Replies
View Related
