I have question about compatibility. I had set up two Cisco AP AIR-AP1131AG-E-KP. They are set under one SSID whith clients roaming between them. I want to add one or two new APs. I would like to use AIR-AP1142N-E-K9. Are they compatible? Are there any issuess using these two types together?
View 2 RepliesI had problems joining a 1131AG AP to a "new" 5508 WLC with 7.4.100.0 running. This AP has been connected to a, for me unknown controller for years. Now the customer wants to move this AP to a newer 5508 controller with 7.4.100.0 We [URL] could not get this AP to the controller connected. Now I have this AP on my desk. I have a 5508 (7.4.100.0) as well. I connected the AP to the same network as the WLC Management -> AP did not connect, tried to download the "new" IOS but didn't seem to work, same as already in the old tread. So I tried to login to the AP, but it seemed to have a for me unknown Account / Password.
-> I did a reset of the AP by pressing the mode button (about 2-3 sec.) during Power on (not connected to the network). Now I could log on to the AP. I deleted six crashinfos and connected the AP back to the network.
Now the AP joined the controller.
Does a "unknown" Password prevent the AP to join to a other WLC?
The AP hat 15740928 bytes total (6409728 bytes free) space on the Flash: was this enough for the new image? 15740928 bytes total (7798272 bytes free) after deleting the crashinfos
The customer has more AP's that has to join the new controller, would be nice that we don't have to reset all APs.
Today I want to build a wireless bridge using AIR-AP1131AG (running WLC) and TP-LINK wireless router. The result is failed. May I know AIR-AP1131AG is support bridging the wireless connection with other vendor's access point or not?
In the TP-Link I already match its SSID, Channel and put the mac-address of the AIR-AP1131AG. In the WLC I already see too TP-LINK mac-address is already become a client.
I have a Brand new AP that was bought for a site which has a controller, however it was never installed. I was wondering can you downgrade this AP to make it work in stand alone mode as a normal AP?
View 1 Replies View Relatedmy customer has a very basic LAN+WLAN configuration:
- 1 switch (not Cisco)
- 1 DSL router which is the default gateway (not Cisco)
- 2 Wi-Fi Access Points (Cisco AIR-AP1131AG-E-K9)
If he tries to establish a PPTP VPN when he is connected to the wired LAN, it works but when he tries the same from the wireless LAN it doesn't work. He says he'd tested it with Windows Firewall disabled. Is there any configuration command that can enable/disable PPTP VPN traffic pass through a Wi-Fi connection? I've never seen something like this and I use PPTP VPNs over a Wi-Fi connection every day without any particular configuration on the access point.
Here's the APs config:
hostname ...!enable secret ...!aaa new-model!!aaa authentication login default local!aaa session-id common!!dot11 syslog!dot11 ssid ... authentication open authentication key-management wpa version 2 guest-mode infrastructure-ssid wpa-psk ascii ...!power inline negotiation prestandard source!!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache !
[Code] .....
I tried to change the default password Cisco to other by command line but the password cannot work out.
The command line I used are as below :
AP#conf tEnter configuration commands, one per line. End with CNTL/Z.AP(config)#enable passAP(config)#enable password 4dMINO123 ?LINE <cr>
[Code].....
I am currently working on a project where I need to design a complete wireless solution for a huge building. I performed the wireless rf survey by configuring the wap's to broadcast a SSID and walked around gathering rf coverage data. When configuring the test WAP's i did not join them to a lan controller ( AIR-WLC4402-50-K9 ) but simply created a static ip and ssid to broadcast but modified the internal antenna gain to +128 to change the direction of the broadcast. There are two other ap's already joined to the lan controller on a guest network (configured by another contractor) but when I go into the lan controller web gui I do not see anywhere that allows me to modify antenna gain on the individual WAPs. Also, once the waps join the lan controller they dont seem to be accessible via web. How I can I modify gain per wap?
View 14 Replies View Relatedmy hardware set-up : 2x AP 1100 series, 2x AP1131AG (not connected to a Cisco Switch)...all with the latest Cisco iOS
What i want to do is connect these APs and broadcast the same SSID (e.g Aironet and NOT Aironet1,Aironet2..etc). Doing that, a user with a laptop can roam between these APs and won't have to re-enter the password of the SSID every time he changes AP. I would also like the encryption to be with a 128bit password key. From what i have read, i need a local authenticator to do what (Something called Local Radius Server).
We are Deploying New Stand Alone AP (Model:AIR-AP1142N-N-K9) in our infrastrucuture, through out our network, we used 802.11G Adapter for Wifi Clients throughout,
Coulple of Questions i Have,
1) In This New Access point i found only Radio0 -802.11N 2.4 Ghz & 5 Ghz , whether this Model AIR-AP1142N-N-K9 will Support 802.11G Adapters?
2) if Clients Comes up with 802.11 G Adapter will it Negotiate and Connect to it?, through out worldwide our network Wifi Clients used 802.11g network to Connect to wifi Network.
3) Also from Client PC is there a way to find what network adapter its running?
4) Correct me if i am wrong , if Client Laptops having G adapter, i Hope it will not Connect To Access point with N Adapter?
5) if these Access point Does not support G adapter, any way to upgrade or downgrade to other IOS to make this access point support G Adapters?
We have an 2504 wireless controller at the office with 5 LAP1142's. At another office we have a single AP1142 which doesn’t quite reach end to end. Ideally I want drop in another AP1142 to provide end to end coverage. Does AP1142 has a repeater mode? If not is there any way to make two AP1142's work with each other so they appear as a singular access point? Can they be configured to handle roaming?
View 1 Replies View RelatedMy APs 1142N don't join their WLC. APs and WLC management interface are in the same vlan (WLC can ping all the APs). It is strange because it doesn't seem like they are trying to contact the WLC. What's strange is that I have other AP 1142N which joined this WLC without any problem.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
[Code].....
is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies View Relatedjust i have purchased new cisco air-ap1142n-a-k9 wireless access point, trying to configure the wpa2 configuration for security reason, but unable to configure in any security mode. So currently my AP is working no security / encryption mode.
View 16 Replies View RelatedI've got an AIR-AP1142N-E-K9 access point, i've got the Radio0-802.11n(2.4ghz) enabled and the 5.0ghz disabled.
i've got my client real close to the AP and i only get a connection speed of 72Mbs.
Shouldn't i get 150mbs? Maybe some wrong configuration?
I was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
I installed two AIR-AP1142N-E-K9 access points, running a fairly simple config, WPA2 PSK, with AES cipher, both the same SSID.The two access points are connected to Cisco 2960G switches, which are in turn connected to each other, again without any fancy config options, no VLAN's ed.
After a random while, varying from 30 minutes to 15 hours, the access points will stop sending/recieving traffic on the ethernet interface.The units don't stop at the same moment, this also varies seemingly random. It's not related to load or the amount of clients (1 to 15).Only turning on one unit doesn't make any difference.
The units keep sending out their SSID, you can associate to them, but the DHCP requests aren't passed on to the DHCP server which is connected to one of the 2960G's.If you wirelessly connect to the AP and set a manual IP adress you can reach the webinterface and telnet/ssh to the access point. The ethernet link is reported as being up on the access point. Also the switch reports a link on the port to which the access point is connected.Resetting the link does have no effect. The log doesn't mention any errors or warnings.Power cycling or reloading the access point will put it back in working order for a varying amount of time.
Access point version:
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Access point config:
!
! Last configuration change at 14:41:40 +0100 Sat May 12 2012 by admin
! NVRAM config last updated at 14:41:40 +0100 Sat May 12 2012 by admin
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code]...
We are having issue with all our Cicso wireless devices (AIR-AP1142N-N-K9) when connected to Windows 8 Pro users. When copying large files, the connection changes to limited access. The initial connection to the access points is also slow for both windows 7 and windows 8 pcs.
View 3 Replies View RelatedWe have a site running 2 1131AG access points on different floors with the same SSID.There have been issues with connections dropping over the last 2-3 months to some newer laptops and iphones that have been introduced to the network. It is almost totally intermittent and after updating the IOS and laptop drivers where possible, there is a still a problem that wont go away.I have some example logging from both AP's when this happens (apologies for the date/time differences, however the events are all sequential)
View 5 Replies View RelatedI would like to have a support on AIR-AP1142N-E-K9 configurations.How I can config this AP?
View 1 Replies View RelatedI currenly have a cisco AP1142N configured to work with our radius server (It was already configured when I took over the network). I order two additional access points for building coverage on multiple floors. Currently, I uploaded the config of the orginal access point to the new device and I can access the device via web and the ssid is being broadcasted. I then added in the access point into IAS with the radius secret key to our Radius server. When I go to connec to the new access point w/ domain credentials I am not able to establish a connection. I am not very familiar with CISCO products. I followed a video to get the access point up and running w/ an IP from CLI so I could access the web interface and upload the edited config.txt file. Are there any issues with setting up multiple access points w/ a single windows radius (IAS) server?
View 7 Replies View RelatedWe have LMS 3.2.1 and WLC version 7.0.116. I want WLC syslog to be managed by LMS. How can i acheive that..? Any special package need to app d for LMS ..?
View 4 Replies View RelatedSince we have now got a go for upgrading the IOS I have a little difficaulties finding if the current IOS will upgrade correctly to the advised version without any loss.Current version is (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF7 In the realease notes for IOS 12.2(33)SXJ I can't find any upgrade matrix or upgrade train.Will this version upgrade without causing any mishaps on current WiSM(ver.1) and switch config?I didn't get any adequate answer, but since NO ONE did mention any repercussions, we did the upgrade......and we did loose configuration !Still the WiSM (version 1) is working all right, but where did the related WiSM configuration go?.How can you do a span session if you have no interface to tie onto?
View 7 Replies View Relatedi want to pick a 3g gateway HUAWEI B683 Router for my official use, but my computer is running for Mac OS, i don't know whether it is compatible with my Mac OS or not,
View 1 Replies View RelatedI have some concern regarding the compatibility of AP with the WLC. we are using AIR-CT2504(7.0.116.0) series WLC with AP AIR-LAP1242AG(7.0.116.0) but now i checked on Cisco website they are End-of-Sale/End-of-Life for the Power Supply for Cisco Aironet 1130, 1140, 1240 and 1300 Series Access Point.
Now My question is:
1: Which is the latest AP series we should use for WLC 2500 series?
Our company recently inherited a group of locations that have Nortel 2270 WLC's with Cisco firmware and have a mixture of 1010 and 1030 LAP's. We are trying to map out an upgrade path for them but I am having difficulty getting the following information, even directly from Cisco. So I have the following questions:
1. Does the 2270 WLC support any other model of Cisco LAP other than the 1010 and 1030?
2. Will a newer controller, say a 2100 or 4400, be compatible with the 1010 and 1030 LAPs already at these locations?
3. Is there anywhere I can find a list of Cisco controllers (EOL and otherwise) and what LAPs they support?
I have a Linksys WRT54GL wireless G router and I just brought a Roswell Wireless N card. would these two items be compatible with one another? or would I need a new router/adapter?
View 4 Replies View Relatedwith FW 7.4.100.0 a 2500 controller works as anchor controller, now.I have 3 questions.
1) What are the limitations? 15 EoIP tunnel, Clients? something else?
2) Have Cisco a compatibility matrix about Anchor - Foreign Firmware? (Example works 7.4.100.0 anchor with 7.0.x.x foreign?)
3) A controller works only as anchor. A controller version with lowest AP licence is needed. Right?
if Cisco Wireless controller works with another vendor AP? I am particular about Motorola 5131. If YES, which Cisco Wireless controller series does the magic and at what efficiency?
View 1 Replies View RelatedI have two questions -
1) Is it possible to connect Cisco 4404 Controller (or ny other controller) to Nexus 7K series.
2) If yes, then what will be the configuration. Will it be similar to link Aggregation with Catalyst 6500 Neighbor Switch.
We currently run six 4402 Wireless lan controllers - these are managed by a WCS server - soon to be replaced by Cisco Prime. We run a mixture of LAP1242 and LAP1142 wireless access points. I need to add more but have been told by my supplier that the both these AP's are now end of sale and cannot be purchased.
The replacement AP's are the 2600 series - but I have been told that these are not compatible with my existing 4402 controllers.
To make matters worse I was then advised that if I purchase the new 5580 controllers the older LAP1242 access points will not work with it and require replacing - this, for me, is a lot of access points.
What I need to know is:
What access points, if any, are currently available that are compatible with my 4402 controllers and a future 5508 installation?
I ssem to be in a situation now where I cannot buy any access points that will work with my 4402's but if I upgrade all my current 1242's will not funtion with the new 5508 controller!
For "AIR-CAP3602E-E-K9 the compatible antenna is AIR-ANT2524DG-R". kindly suggest if antenna part # AIR-ANT2422DG-R= is compatible with AIP-CAP3602E-E-K9.
View 3 Replies View RelatedI would like to know wich wireless card are compatible for backtrack 5 i was planning to buy this card AWUS036H would like to know if its compatible and working well or is there some cards that are better?
View 1 Replies View RelatedI have a cisco/linksys wireless router connected to a cable modem. Also a belkin universal range extender in another part of the house, which picks up the wireless router signal and boosts it - but not very strongly. The belkin RE can also be used as an access point. Can I run a wire & connect it to the cisco/linksys wireless router? Will my laptop pick up the wireless signal from either device depending where in the house it is?
View 1 Replies View Related