I have two questions -
1) Is it possible to connect Cisco 4404 Controller (or ny other controller) to Nexus 7K series.
2) If yes, then what will be the configuration. Will it be similar to link Aggregation with Catalyst 6500 Neighbor Switch.
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedI have a Cisco 4404 wireless lan controller managing about 85 AP's.
The wireless side is setup for a private wlan and a public wlan. On the public side, users are directed to a captive-portal agreement page before they can get on the internet. My question is if there is a way for a single client, specified by either mac address or static IP , can be connected to this wlan without being prompted for the agreement page? I would like to setup a wireless printer for guests connected to this public side.
Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
Our company has 8 4404-100 Cisco wireless controllers and each WLC has 8 W LANs configured. They are all working fine. However, the WLAN ID sequence is not consistent. I'm wondering if it's possible to change the WLAN ID on these WLCs without (or slightly) impacting the users. I don't want to re-configure all the WLAN profiles.
View 13 Replies View RelatedThis is what the Log shows when I try adding a 4404 to NCS
[2012-09-11 12:37:04,199] [ICE Service[ 1]Thread: 7] [inventory] [INFO ] - Complete inventory for deviceid 11020009 at Tue Sep 11 12:37:04 EST 2012. Total time taken to collect inventory in milliseconds = 1304
[2012-09-11 13:48:41,707] [http-443-10] [inventory] [INFO ] - Device with id 11020010 is managed state now, initial inventory collection started
[2012-09-11 13:48:41,768] [http-443-10] [inventory] [INFO ] - Initial inventory collection completed for device with id 11020010 without exception
[2012-09-11 13:48:41,822] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Enter collect inventory for deviceid 11020010 at Tue Sep 11 13:48:41 EST 2012
[2012-09-11 13:48:41,960] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Called InventoryCollectorEngineXdeImpl.call()for device ID = 11020010.
[2012-09-11 13:48:42,045] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Invoking FeatureRunner [returned result: mib2-bootstrap] for MNE collection of device: 11020010)
[2012-09-11 13:48:42,159] [ICE Service[ 1]Thread: 8] [inventory] [ERROR] - 192.168.12.77 No matching device profile found.......
[code]....
How many SSID can be create in a 4404 controller and also in standalone 1250 AP? How many VLANs can be created in eac one?
View 2 Replies View Relatedwe are in the midst of designing a wireless Mesh AP solution for our customer.
Customer Requirement:-
1. Customer wants to deploy REmote MEsh APs (1500 Series) with a centralized 4404 Controller at HQ site.
2. The Remote and HQ site is linked thru a leased line with 2 routers in between
Based on cisco's document REAP and HREAP is not supported in LWAPP Mesh APs. So if the Mesh APs were to be deployed at Remote sites (3 total). How this be achieved?
We recently acquired a 4404 Cisco controller for our network and have been adding our 1200 and 1130 Access points to the controller.This was accomplished by upgrading the APs to LWAPP and then they would automatically be discovered by the controller and then join. Lately, new 1131 APs that have undergone the same process, are not joining the controller. They are discovered but then the close the connection. We are running a flat network so all devices are in the same subnet.Software Version of the controller 6.0.188.0. [code]
View 5 Replies View RelatedIf the 2600 series access points are compatible with a 4404 controller running 7.0.235.3 code? I was looking for a compatibilty matrix for the AP to controller to code comparison but couldn't find one.
View 1 Replies View RelatedOur company recently inherited a group of locations that have Nortel 2270 WLC's with Cisco firmware and have a mixture of 1010 and 1030 LAP's. We are trying to map out an upgrade path for them but I am having difficulty getting the following information, even directly from Cisco. So I have the following questions:
1. Does the 2270 WLC support any other model of Cisco LAP other than the 1010 and 1030?
2. Will a newer controller, say a 2100 or 4400, be compatible with the 1010 and 1030 LAPs already at these locations?
3. Is there anywhere I can find a list of Cisco controllers (EOL and otherwise) and what LAPs they support?
if Cisco Wireless controller works with another vendor AP? I am particular about Motorola 5131. If YES, which Cisco Wireless controller series does the magic and at what efficiency?
View 1 Replies View RelatedI am in the process of building a small educational lab. I just want to make sure that I am not going to have any AP registration/join issues due to regulatory compatibility with a AIR-WLC2106-K9 controller and a AIR-LAT1142N-N-K9 access point. Will this work and if so, will I then be in the clear as far as having devices like my computer and phone attach to the SSID?
View 5 Replies View RelatedWe currently have a 4404 controller that is approaching 100 AP’s (their max). The boss would like to add redundancy into the project. Which leaves me with a lot of questions and I am fairly new to cisco WLAN controllers.While a second 4404 would cover for redundancy would that be true if the AP’s pass the 100 mark?If I get a bigger controller that can support more than 100 (5508?)can the existing 4404 still work in the plan as a backup?Or do I just need to purchase two bigger units and auction off the 4404?
View 3 Replies View Relatedis the LMS 4.1 supports Nexus 7000 baundle ?
View 2 Replies View RelatedThe below nexus 5020 nx-os version and type/revision of my GLC-T is compatible with each other? I noticed also the "Transceiver calibration is invalid" when i do show int e1/8 transceiver details , what does it mean?
View 8 Replies View RelatedI am looking to see if Nexus 5596UP & Nexus 2248TP GE compatible with SFP-10G-SR? The reason is because a consultant was hired on to "design" the network layout and has decided to purchase Cisco SFP+ Copper Twinax Cables which have a 10M limit. A small handful of the Data Center racks are 10-15M away... just out of reach of the Twinax. I would prefer NOT to move the LAN row so that it is more centered in the room. Can I use the SFP-10G-SR to connect the 2 switches (5596 & 2248) together? This SFP has a 26M reach on standard 10gig fiber, the small cost increase per connection is of no concern.
View 2 Replies View RelatedHow will I know if my catalyst and Nexus switch supports Ethertype 0x05ff. This is for the beacon probes sent out by our ESX Servers.
We will be using Nexus 3048 and we have 3750 catalyst switches as our distro switches.
I wanted to know that in nexus 7009, can i use mix of F2/M1/M2 series line cards ? will they work with each other ? Lets say i have F2 line card and M2 line card, will servers attached to them will communicate with each other ?
View 4 Replies View RelatedI have a Cisco WLC 4404 with version software 7.0.230.0 and it gived me a this logg
Oct 9 15:43:08 192.168.122.34 WLC_4404_CC: *osapiReaper:
Oct 09 15:41:49.549: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/895/stat.(erno 24)
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedWe are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies View RelatedI am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
I have a Cisco 4404 WLC that is up, has green status light, the interfaces are showing activity. I see it connected to my Cisco 6500, (Sh port status) it shows connected and trunking,; I also see a lot of activity on the interfaces. Also it will not let me console in, I can console in on my other Cisco 4404 WLC's with out and issues, so I know my cables and configure are correct. The only change a I made today was the time zone. I noticed the time was off by a hour and noticed that the time zone wasn't set so I set it correctly. Shortly after that I saw the WLC go belly o up in my WCS. I tried rebooting the WLC several times without luck. Since I can not gain access via the console I can not really trouble shoot.
View 10 Replies View RelatedWe have 2 4404 controllers running 6.0.x code. I have several SSID setup with different VLANS. When the clients associate they do not show the name of the AP they are connected to, is there any way to display the assocated AP name?
View 2 Replies View RelatedI am facing a strange problem in my WLAN Setup. none of my wireless clients are able to associate with Wireless LAN but when I delete and create a new wireless profile in WLC 4404 clients starts associating with WLAN. every 2-3 days I had to delete and create wlan profile. Is it related to IOS bug or any other problem? My Wireless LAN Controller image is AIR-WLC4400-K9-5-1-151-0.aes.
View 4 Replies View RelatedI have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies View RelatedI have Cisco 4404 WLC with Image 7.0.235.0 We have one SSID Sup_Admin with following config. Which is getting the IP address from the interface pool “corp”.
WPA+WPA2 with AES and TKIP
Auth key Mgmt is 802.1X
We are using Cisco ACS as radius server On the same WLC I have created another SSID Corp_Admin . Which also should get the IP address from the interface pool “corp”. Both SSID has the same settings ,but the second SSID is not working.
The story is that we recently upgraded our 4404 controller to the new 7.2.0.230 code. This upgrade was from 4.2.209 code. I would like to make the change to the Multicast setup so that It is multcasted and not unicasted.So I went into the controller and selected MULTICAST for AP multicast mode and entered in a multicast ip of 239.255.1.60 ( default choosen in the cisco howto's)I then test the reason for enabling the multicast and it doesnt work. The problem is that the Wireless HP printers setup to use Apples IPRINT are not able to be found. However, when I select the Multicast setting for the APs to be UNICAST the Ipads can find the Printers and print to them.What am I doing wrong with this Multicast setting? Do i need to add a Multicast address to the router?
View 2 Replies View RelatedCurrently Being Moderated Wireless users getting disabled
View 6 Replies View RelatedWLC4404 - United States
Software Version 5.2.193.0
where the new WLAN dosn't seem to be routing... but it's not related to name length (ours only 6 charecters). It's almost seems like the new WLC interface (interface2) isn't configured for the same subnet that it's plugged into, but it is.We actually have 2 WLANS. Alot of the original config was done before my time, between about 3 different people. The original WLAN config works fine, but part of the problem is the WLC4404 was configured our server VLAN, thus when a client gets an IP, they are placed on our main server VLAN. Our WLC4404 is connected to our 6509 in our Datacenter, and we have dozens of PTP T1's to our remote offices, which all have WAPs.On the WLC4404, I've configured a new interface on port 2, vlan404, and I have the new WLAN using that interface. The WLAN security is using WPA2, and authenticates via our ActiveDirector services, as well as handing out DHCP from our Windows DHCP server.
The client wireless PC is able to connect to the WAP, but unable to connect to anything else. It can only ping the WLC4404 interface2 address, and nothing else. It does receieve DHCP info (via WLC via Windows DHCP server), but cannot see DHCP server.From the WLC4404: I can telnet into the management IP address, and can ping PC's on the new WLAN, and anyplace else, except the vlan gateway ip address on the 6509.From the 6509: when telnetted in, I can ping everything except interface2 of WLC on vlan404 and the wireless PC using the new WLAN. I am able to ping the ip address of int for vlan404. The 6509 somewhat see's the WLC int2 & wireless PC. Show ARP | inc 404 from the 6509 shows the IP's of the VLAN int, WLC int2, and wireless PC. Show mac-add-tab | inc 404 shows the WLC and wireless PC on same 6509 port.From my work PC (via LAN) at a remote location: I can ping everything except Int2 on the WLC, and the wireless PC.
Is there a command like the "| include" command to filter comand results? For example say I want to find a specific client mac in the "sh dhcp leases" output. On a router or switch I would just type "sh ip dhcp binding | include (mac address). Is there something like this on the WLC CLI?
View 4 Replies View RelatedI am new to Cisco wireless and would like replacing WLC 4404 with 5508. I mean any link or doc (best practices).
View 13 Replies View Related