Cisco Wireless :: Replacing WLC 4404 With 5508
Jun 10, 2013I am new to Cisco wireless and would like replacing WLC 4404 with 5508. I mean any link or doc (best practices).
View 13 Replies
ADVERTISEMENT
Cisco Wireless :: Migrate All Access Point Association From 4404 To 5508
Sep 17, 2012In our current Setup we have one WLC 4404 with 100 Access point license, now we have bought 3 number of 5508 WLC each supporting 100 Access point. Our plan is to Migrate all the Access point assosiation from 4404 to 5508. [code]
View 4 Replies View RelatedCisco :: WLC 4404 / 5508 Web Authentication By AD Security Groups
May 3, 2012web authenticate users within a specific Active Directory Security Group. I tried to authenticate over Radius with Cisco Secure ACS and Network Access Restrictions. But NAR only works with Layer 2 authentication. And Web Authentication over LDAP can only be used with User Objects.
View 5 Replies View RelatedCisco Wireless :: 4404 Guest Anchor Controller With 5508 Foreign Controller?
Aug 12, 2012I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedCisco Wireless :: WLC 4404 Gives A Log
Oct 9, 2012I have a Cisco WLC 4404 with version software 7.0.230.0 and it gived me a this logg
Oct 9 15:43:08 192.168.122.34 WLC_4404_CC: *osapiReaper:
Oct 09 15:41:49.549: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/895/stat.(erno 24)
Cabling / Cards :: Replacing The Wireless Card
Dec 28, 2011My wireless card on my gateway laptop isn't working anymore.I have already tried uninstalling and all of that. I am just going to replace it. I currently have a Intel 3945ABG network card. Is there another network card I can replace it with that is more efficient and quicker? Not sure what other information is needed to figure out what network cards are compatible.
View 2 Replies View RelatedCisco Wireless :: 4404 WLC Up But Will Not Respond
Dec 19, 2012I have a Cisco 4404 WLC that is up, has green status light, the interfaces are showing activity. I see it connected to my Cisco 6500, (Sh port status) it shows connected and trunking,; I also see a lot of activity on the interfaces. Also it will not let me console in, I can console in on my other Cisco 4404 WLC's with out and issues, so I know my cables and configure are correct. The only change a I made today was the time zone. I noticed the time was off by a hour and noticed that the time zone wasn't set so I set it correctly. Shortly after that I saw the WLC go belly o up in my WCS. I tried rebooting the WLC several times without luck. Since I can not gain access via the console I can not really trouble shoot.
View 10 Replies View RelatedCisco Wireless :: 4404 And Connected AP Name
Apr 17, 2011We have 2 4404 controllers running 6.0.x code. I have several SSID setup with different VLANS. When the clients associate they do not show the name of the AP they are connected to, is there any way to display the assocated AP name?
View 2 Replies View RelatedCisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work
Aug 24, 2011iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedLinksys Wireless Router :: Replacing WRT150N With E2500?
Sep 1, 2012I want to replace a WRT150N with an E2500 and retain the setup/settings of the WRT150N.
View 2 Replies View RelatedCisco Wireless :: WLC 4404 - Wi-Fi Connectivity Getting Hanged
Apr 24, 2011I am facing a strange problem in my WLAN Setup. none of my wireless clients are able to associate with Wireless LAN but when I delete and create a new wireless profile in WLC 4404 clients starts associating with WLAN. every 2-3 days I had to delete and create wlan profile. Is it related to IOS bug or any other problem? My Wireless LAN Controller image is AIR-WLC4400-K9-5-1-151-0.aes.
View 4 Replies View RelatedCisco Wireless :: 4404 How To Limit SSIDs Per AP
Mar 22, 2009I have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies View RelatedCisco Wireless :: 4404 - SSID With WPA1+2 802.1X?
Sep 9, 2012I have Cisco 4404 WLC with Image 7.0.235.0 We have one SSID Sup_Admin with following config. Which is getting the IP address from the interface pool “corp”.
WPA+WPA2 with AES and TKIP
Auth key Mgmt is 802.1X
We are using Cisco ACS as radius server On the same WLC I have created another SSID Corp_Admin . Which also should get the IP address from the interface pool “corp”. Both SSID has the same settings ,but the second SSID is not working.
Cisco Wireless :: WLC 4404 Getting Multicast To Work
Mar 20, 2012The story is that we recently upgraded our 4404 controller to the new 7.2.0.230 code. This upgrade was from 4.2.209 code. I would like to make the change to the Multicast setup so that It is multcasted and not unicasted.So I went into the controller and selected MULTICAST for AP multicast mode and entered in a multicast ip of 239.255.1.60 ( default choosen in the cisco howto's)I then test the reason for enabling the multicast and it doesnt work. The problem is that the Wireless HP printers setup to use Apples IPRINT are not able to be found. However, when I select the Multicast setting for the APs to be UNICAST the Ipads can find the Printers and print to them.What am I doing wrong with this Multicast setting? Do i need to add a Multicast address to the router?
View 2 Replies View RelatedCisco :: WLC 4404 Wireless Users Getting Disabled
Dec 28, 2011Currently Being Moderated Wireless users getting disabled
View 6 Replies View RelatedCisco Wireless :: WLC 4404 AP Not Routing Via Second Interface
Aug 20, 2012WLC4404 - United States
Software Version 5.2.193.0
where the new WLAN dosn't seem to be routing... but it's not related to name length (ours only 6 charecters). It's almost seems like the new WLC interface (interface2) isn't configured for the same subnet that it's plugged into, but it is.We actually have 2 WLANS. Alot of the original config was done before my time, between about 3 different people. The original WLAN config works fine, but part of the problem is the WLC4404 was configured our server VLAN, thus when a client gets an IP, they are placed on our main server VLAN. Our WLC4404 is connected to our 6509 in our Datacenter, and we have dozens of PTP T1's to our remote offices, which all have WAPs.On the WLC4404, I've configured a new interface on port 2, vlan404, and I have the new WLAN using that interface. The WLAN security is using WPA2, and authenticates via our ActiveDirector services, as well as handing out DHCP from our Windows DHCP server.
The client wireless PC is able to connect to the WAP, but unable to connect to anything else. It can only ping the WLC4404 interface2 address, and nothing else. It does receieve DHCP info (via WLC via Windows DHCP server), but cannot see DHCP server.From the WLC4404: I can telnet into the management IP address, and can ping PC's on the new WLAN, and anyplace else, except the vlan gateway ip address on the 6509.From the 6509: when telnetted in, I can ping everything except interface2 of WLC on vlan404 and the wireless PC using the new WLAN. I am able to ping the ip address of int for vlan404. The 6509 somewhat see's the WLC int2 & wireless PC. Show ARP | inc 404 from the 6509 shows the IP's of the VLAN int, WLC int2, and wireless PC. Show mac-add-tab | inc 404 shows the WLC and wireless PC on same 6509 port.From my work PC (via LAN) at a remote location: I can ping everything except Int2 on the WLC, and the wireless PC.
Cisco Wireless :: WLC 4404 CLI Output Modifier
Dec 26, 2012Is there a command like the "| include" command to filter comand results? For example say I want to find a specific client mac in the "sh dhcp leases" output. On a router or switch I would just type "sh ip dhcp binding | include (mac address). Is there something like this on the WLC CLI?
View 4 Replies View RelatedCisco Wireless :: Can Change IOS Version On LAP From WLC 4404
Aug 8, 2011My WLC 4404 runs with Software Version 5.2.193.0. The built-in IOS for AP is Version 12.4(18a)JA2.I run into problem same as in CSCta29484 Bug (Radio stops beaconing for 10-second period).I would like to try fixed image for LAP without upgrade WLC. Is it possible?
View 5 Replies View RelatedCisco Wireless :: Free Memory On 4404-100
Aug 29, 2012From what I can see on some of the message discussion boards, this is an alert only message. I would like to get clarification that this will not cause operational issues with the controller.
I did try to change the free memory by using the command
config memory monitor leaks 10000 300000
but then I get a response about core dumps and the alerts do not go away.
Cisco Wireless :: 4404 - SNMP Configuration In WLC
Jul 22, 2011if there is document available for SNMP configuration for WLC 4404?
View 4 Replies View RelatedLinksys Wireless Router :: E2500 - Replacing Netgear With No Success
Jan 21, 2012I purchased an E2500 wireless router. I am trying to replace a Netgear wilreless router with no success. During installation my laptop reaches about 25% and I get an error message. In short my laptop asks for an IP address with a password. Once I enter that information I receive an error message to call for assistance.
View 1 Replies View RelatedLinksys Wireless Router :: Replacing BEFSR41 With WRT54G / Can't Connect To 192.168.1.1
Jan 2, 2012I am trying to replaced our wired router (BEFSR41) with a wireless router (WRT54G V5) that we have floating around. When connected through the wireless router, I am unable to access 192.168.1.1. I went to the command prompt and The IP Address and the Default gateway are both blank. I even tried to manually set the default gateway to 192.168.1.1 but I was still unable to connect. Currently, I am connected directly to the modem so that I may use the internet for troubleshooting. I've tried releasing and renewing the ip, but it will not renew.
View 2 Replies View RelatedCisco Wireless :: WAP4410N Increase Range Of Access Point By Replacing Antenna
Jun 17, 2011I have a WAP4410N access point. In the datasheet, it shows that the Antenna Gain in dBi as 2. I need to increase the range of the access point by replacing the antenna with a 7dB one. I would like to know the maximum dBi supported by this access point.
View 0 Replies View RelatedCisco Wireless :: 1142N APs Cannot Join 4404 WLC In The Same VLAN?
Jul 31, 201210 Access Pointd 1142N setup on vlan 10 and the controller management is in vlan 10.
They get DHCP IP addreses from the controller itself!! I do not have another DHCP server.
Here is what I get wich debug capwap event and debug capwap packet
(Cisco Controller) >*spamReceiveTask: Jul 31 12:21:41.283: <<<< Start of CAPWAP Packet >>>>*spamReceiveTask: Jul 31 12:21:41.283: CAPWAP Control mesg Recd from 10.128.186.104, Port 51743*spamReceiveTask: Jul 31 12:21:41.283: HLEN 4,
[Code].....
Cisco Wireless :: Cannot Add WLC 4404 To WCS After Turning On LAG - Device Not Found
Sep 19, 2011we took one of our controllers and turned LAG on and since then it is unreachable on the WCS. The controller is running version 7.0.116.0 and the WCS is running 7.0.172.0. I can access teh WLC no problem through web interface and CLI, as I can also do this with the WCS as well, but the WCS cannot access the WLC.From CLI i can ping the WCS from the Controller and get a response, but from CLI on the WCS, I cannot ping the controller.
View 5 Replies View RelatedCisco Wireless :: 4404 - Configuring WLC With Other VLan And Subnet
Sep 16, 2012I have currently Ciso4404 WLC installed which is in vlan4001 with the 172.16.10.0/24 subnet
I have bought Cisco 5508 WLC recently as AP count is increased... Can I install it in same vlan and subnet? If yes what would be the setting for APs to join... If no how can I configure it with other vlan and subnet..
Cisco Wireless :: 4404 WCS 6.0 Access Point Groups
Jul 18, 2011I am currently running with code WCS wityh 10 4404 controllers across 3 sites.I am currently at code level 4.2.207, and actively employ Wireless VLAN Override.I understand that when I upgrade to code 6.0.202.0, that Wirelss VLAN Override is not available, and that I would need to configure Access Point groups.I can configure the groups, however I note a caution from: url...
Note: AP groups do not allow multicast roaming across group boundaries. AP groups allow APs on the same controller to map the same WLAN (SSID) to different VLANs. If a client roams between APs in different groups, the multicast session does not function properly because this is currently not supported. Currently, the WLC forwards multicast only for the VLAN configured on the WLAN and does not take into consideration VLANs configured in AP groups.We use Vocera here across all our sites, and Wireless VLAN Override works a treat, however I'm concerned I may come across problems with a roaming Vocera badge andAccess Point Groups - in that the badge may lose connectivity?
Cisco Wireless :: WLC 4404 Authentication Of Devices To Wi-Fi Network
Aug 2, 2012I'm facing a problem related to devices authenticating to our wireless network. Below are how it is setup:WLC 4404 pass authentication to ACS 5.3 (PEAP + MsChapV2) then to AD server.Client can get stock in this status and it keeps repeating from 1 to 20.
View 4 Replies View RelatedCisco Wireless :: 4404 / Restricting Use Of Guest Accounts?
Aug 15, 2011I am currently running a guest wireless network using 4404 controllers on the wireless side and a 4402 as an anchor controller, all running 7.0.98.0 and all is working fine. Accounts being created via the WCS lobby admin and applied to the 4402.The question I have is, is there any way of restricting the use of an account to 1 device at a time. I am currently seeing evidence of password sharing and my boss would like to make sure that everyone who use the system has their own credentials.
View 1 Replies View RelatedCisco :: Wireless Lan Controller 4404 Exclusion Setting?
Nov 12, 2012I have a Cisco 4404 wireless lan controller managing about 85 AP's.
The wireless side is setup for a private wlan and a public wlan. On the public side, users are directed to a captive-portal agreement page before they can get on the internet. My question is if there is a way for a single client, specified by either mac address or static IP , can be connected to this wlan without being prompted for the agreement page? I would like to setup a wireless printer for guests connected to this public side.
Cisco Wireless :: 4404 Controller Compatibility With Nexus
Oct 9, 2012I have two questions -
1) Is it possible to connect Cisco 4404 Controller (or ny other controller) to Nexus 7K series.
2) If yes, then what will be the configuration. Will it be similar to link Aggregation with Catalyst 6500 Neighbor Switch.
Cisco :: Acs 4.2 PEAP Machine Authentication Wireless 4404
Sep 26, 2012we have acs 4.2 as our radius server, and 2 wlc 4404 with a wism2 for our wireless network. we have 2 SSID network, lets call them SSID A and B. A have a more restricted access to server than B.PEAP machine authentification is authorize on both network, to let our users laptop connect before the user login, this enable us to have our computer gpo deploy before the user logon, or have network access to authenticate a user to our directory if he had not logon previously on the laptop.
Users from group A can't logon to SSID B, they can only logon to SSID A, but we have some clever users from group A who have change they wireless setting to only send machine authentification (this can be done in the advance setting of a wireless network in windows 7) to connect to SSID B
We can't force the wireless config by GPO because we don't have an ad 2008 domain, we are still in 2003 soo we can't change the gpo for windows 7 wireless setting . I can't force user to require machine authentification and user authentification because we have a lot of ipad and iphone, and other mobile device that connect using only their user credentials.Is there a way I could configure this without having to disable machine authentification for SSID B?
Cisco Wireless :: Can't Join 1121-AG To Controller 4404 WLC
Jan 4, 2012Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.