I have currently Ciso4404 WLC installed which is in vlan4001 with the 172.16.10.0/24 subnet
I have bought Cisco 5508 WLC recently as AP count is increased... Can I install it in same vlan and subnet? If yes what would be the setting for APs to join... If no how can I configure it with other vlan and subnet..
10 Access Pointd 1142N setup on vlan 10 and the controller management is in vlan 10.
They get DHCP IP addreses from the controller itself!! I do not have another DHCP server.
Here is what I get wich debug capwap event and debug capwap packet
(Cisco Controller) >*spamReceiveTask: Jul 31 12:21:41.283: <<<< Start of CAPWAP Packet >>>>*spamReceiveTask: Jul 31 12:21:41.283: CAPWAP Control mesg Recd from 10.128.186.104, Port 51743*spamReceiveTask: Jul 31 12:21:41.283: HLEN 4,
[Code].....
I have a tale of woe for you who may be considering Hybrid REAP with local switching.
My client has a varied configuration, but the requirements basically screamed HREAP with local switching. They have 15 sites, had already purchased a single WLC 4404 and they needed between 4 and 24 APs at each of the sites. Each of these locations are connected by a WAN link of good quality, but only a single link so there is no assurance of availability; the client has local resources so it would be useful if wireless stayed working during an outage.
So I setup the WLC for HREAP local switching. I setup AP Groups VLANs, but I noticed it had no effect on the VLAN allocation for HREAP. This was unfortunate, because not every site has the same VLAN configuration - some sites had a L3 switch and others only a L2 switch. But I suffered through this and configured each AP manually with the appropriate VLAN mappings.
The infuriating thing, is now that they have bought a second WLC 4404 (they expect to increase the number of APs beyond 100) all these VLAN mappings are messed up when APs connect to the second WLC. I've been going through them one by one again - it is really unfortunate that the AP Groups VLAN mappings don't apply to HREAP local switching.
I'm going to get back to the next 80 APs - but if some of you have a system for handling the VLAN mappings of a large number of APs.
I have got a wireless project with WLC main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .
ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0
and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.
I have a RV042 with two ADSL services on it, that is a nice simple thing for this unit. The problem that I am having though is that one of the ADSL services also has a /29 attached to it.
How do you go about configuring this additional sub net? On a previous unit I have had to create IP aliases, and could then port forward and NAT without too many issues, but it doesn't appear that the RV unit seems to work the same way.
If all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.
View 3 Replies View RelatedI have a Linksys WAG120N Wireless-N ADSL2+ Modem Router. The firmware version is V1.00.12.I run a Windows machine attached to the router which has a certain sub network address. On that same machine I run a Virtual Machine with Linux which has its own address, 192.168.1.102. I've been noticing that whenever I shut down either machine and then turn them back on later, they acquire another address, which makes it annoying for me to make them communicate between each other (by, for example, trying to load a webpage hosted on the VM from the physical machine) without knowing the actual address, which, as I said earlier, seems to change every time.
I'd like to know if there's a way (with my router model) to configure it so that the sub network address of both machines remains the same, no matter whether or not they've been shut down and restarted.
I have a AP541N connected to a UC560. We are currently configured for Wireless Voice and Data. We have added a Guest VLAN, but don't see where in CCA to secure the VLAN from accessing the other other two default VLANs.
Additional Info: AP541N-K9-1.7(2)UC560 15.0(1)XA2, RELEASE SOFTWARE (fc2)CCA 3.0
i have 2x 27 subet ( we will call first /27 fip and call second /27 sip) we assign sip subnet to our virtual machine and we do not want assign ip from sip to our physical node and we wan assign ip from fip subnet to our physical server, because we want sip can not spoof physical server ips, so when we create vlan in our switch we set port 1 and fip and sip subnet access to this vlan in this senario can my virtual machine spoof our physical node ip ? some one in my datacenter technical team told me we should create vlan for fip and create a seprate vlan for sip then set vlan fip and vlan sip access to switch port #1 is it right? if it is ok can some one give me the commands for this senario which create 2 spetare vlan and access them to port siwtch #1 for exaple? we have cisco 2960 48 port ,
View 2 Replies View RelatedI am designing a network right now that is going to have 356 devices. I need to use vlan separation with subnetting for a number of reasons. The first (and most obvious) is that there are 356 devices that will require an IP. Too many for one subnet. The second is that a good portion of the devices that I am using are a litlle to chatty with the broadcast traffic for my comfort. I have two subnets that are going to be specifically alocated to these chatty devices. Our switches are being provided for us by the client for unknown reasons. They are providing us with HP ProCurve E2810 switches which are layer2 switches.
View 1 Replies View RelatedJust got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected. It's new for me as the previous Job i was sorking with a ws-3750-48.
i did from console change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out.. i need to reboot the switch..
I'm new to Cisco equipment much more familiar w/ Sonicwall w/ that said......I have a 5505 w/ Security Plus licensing
I have set up multiple VLANs as follows
VLAN 1 inside - still setup as 192.168.1.1 (will not be using this for our lan)
VLAN2 - outside
VLAN100 - LAN 10.1.1.1/24
[Code]....
If I do add all the VLANs above I understand I will probably have to make a trunk port since I only have 5 usable interfaces
I recently bought SG-300 28P to create the VLAN. My network hs 3 subnet 192.168.1.0, 192.168.2.0 and 192.168.3.0.My main net work is 192.168.1.0. I want to divide it to VLAN to eliminate the boardcast storm; especially from the domain 192.168.3.0
But I want all the devices from 192.168.1.0 to access other subnet.
Scenario: I have a vmserver w four virtual servers all in configured w in different subnets. What's the best way to configure a 3750-x switch to route traffic from the virtual servers to their vlans?
View 2 Replies View Relatedgetting a SF300 to properly route IP between 2 VLANs. I've watched the demo video and performed everything it showed, but I get the most bizarre half-way results. I haven't done anything on Cisco routers in about 15 years, so I'm a little rusty.
We have an office LAN with a cable modem/router for Internet access where the modem/router has IP address 192.168.1.1. We have the usual 24 bit prefix net mask. The SF 300 is connected to this network on port 1.
I have configured port 1 to VLAN 1, interface in Access mode, assigned a static IP address of 192.168.1.36, which is a free address on our office LAN. I have configured port 2 to VLAN 2, interface in Access mode, assigned a static IP address of 192.168.3.1 I put a static route in the modem/router, pointing 192.168.3.0/24 to 192.168.1.36.
I have a PC on 192.168.3.10 attached to port 2.
The SF300 can ping 192.168.3.1, but not 192.168.3.10. 192.168.3.10 can ping 192.168.3.1. It can also ping 192.168.1.1, and can pull up an HTTP router admin page from 192.168.1.1. 192.168.3.1 can be pinged from anywhere on 192.168.1.x, but 192.168.3.10 cannot be pinged from 192.168.1.x. Finally, 192.168.3.10 cannot ping any other addresses on 192.168.1.x except 192.168.1.1, and cannot reach the Internet.
Here's my configuration:
switch6d919d#show runconfig-file-headerswitch6d919dv1.3.0.59 / R750_NIK_1_3_647_260CLI v1.0set system mode router
file SSD indicator encrypted@ssd-control-startssd configssd file passphrase control
[Code].....
I just procured Cisco 3560V2- 48PS-S i would like to know how to set it up from scratch:
1. configuring passwords: enable and privilege
2. Creat Vlan , such that systems connected to the Vlan can connect to internet.
3. enable routing protocols
4. How do i use the switch as a default gateway for the systems on the vlan
5. how do i make sure the desktops connected to the switch are browsing the internet.
I have a 2232 dual homed to 2 5548's via a port-channel/ vpc. I have one 5548A and configure the port for the 2232 with a vlan, plug into that port and it doesn't come up (inactive). I go to 5548b (Primary) and configure the port and it comes up.
View 3 Replies View RelatedI currently have two Nexus 5548UP switches in my environment running the latest code (n5000-uk9.5.1.3.N1.1a.bin). Both of these switches are connected via a VPC Peer Link (two ports on each switch in an Ether Channel) and a VPC-Keep Alive Link (a dedicated port). Hosts connect to each switch via a VPC for both IPV4 and FCOE.
As of right now, everything works. I currently have a stack of two 3750 switches that each Nexus is connected to. This stack is doing all the Intra-VLAN Layer 3 Routing for the Nexus Switches. However, I plan to get rid of the 3750s, and move the Layer 3 Routing the Nexus 5548's, so the backplane is 10 Gig instead of 1 Gig.. I have the Layer 3 Daughter Card installed in both switches, as well as the LAN_BASE license.
So, at the moment, I am trying to find the best way to accomplish Layer 3 Routing on these two switches. Since the Nexus switches are not stacked, and the FCOE portion of HA is taking care of by the Multipathing agent on each host, I believe am just concerned with providing Intra-VLAN routing in an HA build where if one switch goes down, VLANs still route through the other switch.
Again, since the Nexus switches are not stacked, I am guessing the best way to handle this is with HSRP, but my experience with that has always been with routers that have a switch in the middle. Can I make HSRP work without having a switch between the Nexus switches? Can I track the VPC peer link, or how do I do it? I guess I am looking for a sample config.
Let's pretend I had two VLANs:
VLAN 20:
10.20.20.254 - GW and 10.20.20.0/24
VLAN 40
10.40.40.254 - GW and 10.40.40.0/24
And I wanted the Nexus switches to route these VLANs regardless of which switch was up / down..
I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
I have a Cisco WLC 4404 with version software 7.0.230.0 and it gived me a this logg
Oct 9 15:43:08 192.168.122.34 WLC_4404_CC: *osapiReaper:
Oct 09 15:41:49.549: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/895/stat.(erno 24)
I have a Cisco 4404 WLC that is up, has green status light, the interfaces are showing activity. I see it connected to my Cisco 6500, (Sh port status) it shows connected and trunking,; I also see a lot of activity on the interfaces. Also it will not let me console in, I can console in on my other Cisco 4404 WLC's with out and issues, so I know my cables and configure are correct. The only change a I made today was the time zone. I noticed the time was off by a hour and noticed that the time zone wasn't set so I set it correctly. Shortly after that I saw the WLC go belly o up in my WCS. I tried rebooting the WLC several times without luck. Since I can not gain access via the console I can not really trouble shoot.
View 10 Replies View RelatedWe have 2 4404 controllers running 6.0.x code. I have several SSID setup with different VLANS. When the clients associate they do not show the name of the AP they are connected to, is there any way to display the assocated AP name?
View 2 Replies View RelatedI am facing a strange problem in my WLAN Setup. none of my wireless clients are able to associate with Wireless LAN but when I delete and create a new wireless profile in WLC 4404 clients starts associating with WLAN. every 2-3 days I had to delete and create wlan profile. Is it related to IOS bug or any other problem? My Wireless LAN Controller image is AIR-WLC4400-K9-5-1-151-0.aes.
View 4 Replies View RelatedI have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies View RelatedI have Cisco 4404 WLC with Image 7.0.235.0 We have one SSID Sup_Admin with following config. Which is getting the IP address from the interface pool “corp”.
WPA+WPA2 with AES and TKIP
Auth key Mgmt is 802.1X
We are using Cisco ACS as radius server On the same WLC I have created another SSID Corp_Admin . Which also should get the IP address from the interface pool “corp”. Both SSID has the same settings ,but the second SSID is not working.
The story is that we recently upgraded our 4404 controller to the new 7.2.0.230 code. This upgrade was from 4.2.209 code. I would like to make the change to the Multicast setup so that It is multcasted and not unicasted.So I went into the controller and selected MULTICAST for AP multicast mode and entered in a multicast ip of 239.255.1.60 ( default choosen in the cisco howto's)I then test the reason for enabling the multicast and it doesnt work. The problem is that the Wireless HP printers setup to use Apples IPRINT are not able to be found. However, when I select the Multicast setting for the APs to be UNICAST the Ipads can find the Printers and print to them.What am I doing wrong with this Multicast setting? Do i need to add a Multicast address to the router?
View 2 Replies View RelatedCurrently Being Moderated Wireless users getting disabled
View 6 Replies View RelatedWLC4404 - United States
Software Version 5.2.193.0
where the new WLAN dosn't seem to be routing... but it's not related to name length (ours only 6 charecters). It's almost seems like the new WLC interface (interface2) isn't configured for the same subnet that it's plugged into, but it is.We actually have 2 WLANS. Alot of the original config was done before my time, between about 3 different people. The original WLAN config works fine, but part of the problem is the WLC4404 was configured our server VLAN, thus when a client gets an IP, they are placed on our main server VLAN. Our WLC4404 is connected to our 6509 in our Datacenter, and we have dozens of PTP T1's to our remote offices, which all have WAPs.On the WLC4404, I've configured a new interface on port 2, vlan404, and I have the new WLAN using that interface. The WLAN security is using WPA2, and authenticates via our ActiveDirector services, as well as handing out DHCP from our Windows DHCP server.
The client wireless PC is able to connect to the WAP, but unable to connect to anything else. It can only ping the WLC4404 interface2 address, and nothing else. It does receieve DHCP info (via WLC via Windows DHCP server), but cannot see DHCP server.From the WLC4404: I can telnet into the management IP address, and can ping PC's on the new WLAN, and anyplace else, except the vlan gateway ip address on the 6509.From the 6509: when telnetted in, I can ping everything except interface2 of WLC on vlan404 and the wireless PC using the new WLAN. I am able to ping the ip address of int for vlan404. The 6509 somewhat see's the WLC int2 & wireless PC. Show ARP | inc 404 from the 6509 shows the IP's of the VLAN int, WLC int2, and wireless PC. Show mac-add-tab | inc 404 shows the WLC and wireless PC on same 6509 port.From my work PC (via LAN) at a remote location: I can ping everything except Int2 on the WLC, and the wireless PC.
Is there a command like the "| include" command to filter comand results? For example say I want to find a specific client mac in the "sh dhcp leases" output. On a router or switch I would just type "sh ip dhcp binding | include (mac address). Is there something like this on the WLC CLI?
View 4 Replies View RelatedI am new to Cisco wireless and would like replacing WLC 4404 with 5508. I mean any link or doc (best practices).
View 13 Replies View RelatedMy WLC 4404 runs with Software Version 5.2.193.0. The built-in IOS for AP is Version 12.4(18a)JA2.I run into problem same as in CSCta29484 Bug (Radio stops beaconing for 10-second period).I would like to try fixed image for LAP without upgrade WLC. Is it possible?
View 5 Replies View RelatedFrom what I can see on some of the message discussion boards, this is an alert only message. I would like to get clarification that this will not cause operational issues with the controller.
I did try to change the free memory by using the command
config memory monitor leaks 10000 300000
but then I get a response about core dumps and the alerts do not go away.