Multiple Vlan / Subnet Network
Apr 4, 2011
I am designing a network right now that is going to have 356 devices. I need to use vlan separation with subnetting for a number of reasons. The first (and most obvious) is that there are 356 devices that will require an IP. Too many for one subnet. The second is that a good portion of the devices that I am using are a litlle to chatty with the broadcast traffic for my comfort. I have two subnets that are going to be specifically alocated to these chatty devices. Our switches are being provided for us by the client for unknown reasons. They are providing us with HP ProCurve E2810 switches which are layer2 switches.
View 1 Replies
ADVERTISEMENT
Jan 25, 2012
I recently bought SG-300 28P to create the VLAN. My network hs 3 subnet 192.168.1.0, 192.168.2.0 and 192.168.3.0.My main net work is 192.168.1.0. I want to divide it to VLAN to eliminate the boardcast storm; especially from the domain 192.168.3.0
But I want all the devices from 192.168.1.0 to access other subnet.
View 4 Replies
View Related
May 28, 2013
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
View 2 Replies
View Related
Apr 4, 2013
The network topology is like this. Router with DHCP_Server on it.
VLAN 10
VLAN 20
VLAN 30
My question is how to configure the router so that all devices on all 3 VLANS can obtain IP from the router. I've tried to enable proxy arp on all interfaces and create sub interfaces and trunk them to their appropriate vlans, but I can't specify the gateway on all trunked sub interfaces because I get a warning that addresses overlap. Then I tried to set access-group on all sub-interfaces and still doesn't work.
View 5 Replies
View Related
Aug 24, 2011
I have a RV042 with multiple subnet, 192.168.10.0 and 192.168.9.0. 192.168.10.0 is assigned to the LAN, 192.168.9.0 is created under multiple subnet. Both subnet can access Internet by accessing IP address, but 192.168.9.0 cannot access Internet by using host name. It looks like DNS is not working for the 9.0 network.
View 1 Replies
View Related
Sep 27, 2012
I'd like to set each individual LAN port with different address i.e. LAN 1 192.168.1.1 and LAN 2 10.1.1.1 instead of using the multiple subnet feature and having all ports replying for the addresses created.
View 3 Replies
View Related
Dec 15, 2010
I have an 1811 as a border router. Initially we had one block from our ISP. We just got a second block of IP's and I'm not sure how to make this work.
Block #1 - Working
209.91.**.129-142 /28
Block #2 - Not Working
209.91.**.146-158 /28
The problem I'm having is block #1's gateway is 209.91.**.129 and block #2's is 209.91.**.145
How do I make it so I can use both blocks in my NAT entries?
View 3 Replies
View Related
Dec 26, 2011
i have 2x 27 subet ( we will call first /27 fip and call second /27 sip) we assign sip subnet to our virtual machine and we do not want assign ip from sip to our physical node and we wan assign ip from fip subnet to our physical server, because we want sip can not spoof physical server ips, so when we create vlan in our switch we set port 1 and fip and sip subnet access to this vlan in this senario can my virtual machine spoof our physical node ip ? some one in my datacenter technical team told me we should create vlan for fip and create a seprate vlan for sip then set vlan fip and vlan sip access to switch port #1 is it right? if it is ok can some one give me the commands for this senario which create 2 spetare vlan and access them to port siwtch #1 for exaple? we have cisco 2960 48 port ,
View 2 Replies
View Related
Sep 16, 2012
I have an ASA which is managing internet access from mutiple VLANs configured on a 3560 switch. I want to be able to limit the 100MB internet connection on the ASA on a per subnet (VLAN) basis for the multiple subnets configured on the switch..
so for example
VLAN10 - 10.0.10.0 - limit to 5MB
VLAN20 - 10.0.20.0 - limit to 10MB
VLAN30 - 10.0.30.0 - limit to 3MB
View 7 Replies
View Related
Apr 1, 2013
I have a home office with multiple VLANS/subnets I have many VPNs that connect only a specific subnet to a specific remote offfice. On a 5520, can I create a S2S VPN to different remote offices that have the same IP scheme, but from different home office subnets? For example at my home office let's say I have two independant, distinct VLAN/subnets: 192.168.140.0/24 and 192.168.150.0/24. Can I create an S2S from the 140 subnet to a remote office with a 10.10.10.0 addressing scheme and another S2S from the 150 subnet to a totally different office also with a 10.10.10.0 scheme?
View 1 Replies
View Related
Sep 16, 2012
I have currently Ciso4404 WLC installed which is in vlan4001 with the 172.16.10.0/24 subnet
I have bought Cisco 5508 WLC recently as AP count is increased... Can I install it in same vlan and subnet? If yes what would be the setting for APs to join... If no how can I configure it with other vlan and subnet..
View 1 Replies
View Related
Aug 12, 2012
I have got a wireless project with WLC main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .
ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0
and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.
View 4 Replies
View Related
Jun 9, 2010
Just got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected. It's new for me as the previous Job i was sorking with a ws-3750-48.
i did from console change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out.. i need to reboot the switch..
View 2 Replies
View Related
May 4, 2011
I'm new to Cisco equipment much more familiar w/ Sonicwall w/ that said......I have a 5505 w/ Security Plus licensing
I have set up multiple VLANs as follows
VLAN 1 inside - still setup as 192.168.1.1 (will not be using this for our lan)
VLAN2 - outside
VLAN100 - LAN 10.1.1.1/24
[Code]....
If I do add all the VLANs above I understand I will probably have to make a trunk port since I only have 5 usable interfaces
View 12 Replies
View Related
May 11, 2012
I have Cisco L3 3560G switch which directly connected with router . i have configured Vlan 2,3 on the switch and assign port 2 & 3 respectably. I want to management both vlan 2 & 3 from from L3 port g0/10 .
View 6 Replies
View Related
Jan 13, 2013
Whether it is possible to have same vlan on multiple interface on ASA 5510 and higher models ?
View 2 Replies
View Related
Mar 7, 2012
I am new to VLANs and Cisco SMB switches. I have a new SGE 2010P switch and i am trying to configure different VLANs, one for data, one for Voice and the other for server.
Is there any tutorial on how to configure VLAN, by the way i tried to used the web interface and admin guide, it totally confused my understanding of Vlans.
View 5 Replies
View Related
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
View Related
Feb 17, 2013
Getting a AIR-AP1141N to work with an existing SRP526.
The SRP has two VLANs and two SSIDS
- VLAN1 - Corporate Wireless
- VLAN100 - Guest Wireless
So far so good. Now we need to extend the Range of the Wireless and bought an AIR-AP1141N. And this AccessPoint works like a charm, BUT only with one SSID,
I configured in the Port Management Area of the SRP526 both VLANs on one Port and configured the Access Point for multiple SSID use, but i don't get an IP from the DHCP Server Range of the VLAN100.
Could it be possible, that die Access Point can not get the tag Information?
View 1 Replies
View Related
Mar 11, 2013
Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies
View Related
Oct 22, 2012
I have two buildings that I'm trying to configure a bridge in between them using 2 1242AG APs.
Building A
PCOFFICE SSID on VLAN 200 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
Root Bridge
Building B
FDAPC SSID on Native VLAN 1 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
We are using directional antenna. I know they are lined up properly because I have them both down and in front of me. I'm getting an error on the Building B AP that says " No SSID with VLAN configured. Dot11Radio1 not started." and I'm unable to get this to work. The bridge was working before I added the VLAN and encryption/WPA information for the PCOFFICE and FDAPC SSIDs
View 15 Replies
View Related
Feb 6, 2013
I have a Cisco 1921 Router, a Cisco Catalyst 2960 and a Cisco Catalyst 2970 and I want the router to be able to assign ip-addresses by what VLAN a device is active on.
VLAN1: 10.0.0.0/24
VLAN2: 10.0.1.0/24
The router is connected to the Catalyst 2960 and there on to the Catalyst 2970 so the VLAN1 and VLAN2 is active on the to switches and the Router.is it possible?
View 8 Replies
View Related
Jun 29, 2012
I have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies
View Related
May 21, 2012
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies
View Related
Mar 12, 2012
I would like to know if it is possible to assign a 3rd IP address to my end user vlan. Basically the 45xx acts as my end user gateway and has been confirgured as below
interface VlanXX
description Main Vlan
ip address 2.X.X.X 255.255.255.0 secondary
ip address 1.X.X.X 255.255.252.0
[Code].....
Here, due to IP address exhaustion in my end-user network, i want to add one more subnet X.X.X.X/22 to my network and assign one IP more from this range to the above vlan to act as the gateway IP.
View 1 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
Mar 6, 2013
We bought a pair of ASR 1004 to be installed at Primar & Secondary data center and one thing is to run OTV over it, but to do that, I have to extend multiple VLANs from my Core (Pair of Nexus 7010s) connected directly to the ASR is Primary Data center, I looked at some documents but didn't get a good idea about it, extend multiple VLANs from Nexus switch to an ASR.
View 2 Replies
View Related
Aug 23, 2011
I have a Cisco 877W-K9 router, and I for the life of me can not work out how to enable multiple SSIDs on the AP whilst keeping them all to the same VLAN?
I know this may seem silly but basically for our clients we setup WPA-Enterprise for one SSID and WPA-PSK for the other to help ease migration between the two etc, however all I can seem to do at the moment is create multiple VLANs and use ip unnumbered vlan1 to sync them all into one, but this seems really silly.
View 2 Replies
View Related
Feb 3, 2013
The field engineer has a stand alone 24 port 2900 series switch that he has different equipment connected to and are segmented using VLANs. So for example, he's got ports 1-4 assigned to VLAN 10, 5-12 assigned to VLAN 20, 13-19 assigned to VLAN 30 and 20-24 assigned to VLAN 40. He would like all the gear on VLAN 30 to have the ablity to talk to all of the other VLANS, but VLAN 40 should not be allowed to talk with any other VLAN. Trunking would do no good here since the switch isn't connected to anything and you can only assign one VLAN per port.
Is there a way to do this within the stand alone switch? The only possible way I could think of would be to ensure that each VLAN has an assigned IP number (subnet) and doing this through access lists.
View 2 Replies
View Related
Feb 12, 2012
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
View 1 Replies
View Related
Oct 25, 2012
I'm new to networking and was looking for some assistance. First off im using packet tracer to diagram my senario as I will be receiving my equipment next week to deploy.
Hardware to be used:
1. 2 catalyst 3560 switches
2. all connect to a sonic wall router
I have two companies that work in the same office space. I need to keep these companies seperate on their own vlan. They will however need to share the phone system.(Packet tracer file uploaded to give those who have the time to see what I put together.) [code]
View 13 Replies
View Related
Jan 11, 2011
In my Institute intranet we have divided the network in various subnets. My subnet ip is 10.100.95.xx. But only my subnet can access the internet the other subnets such as 10.100.94.xx and 93.xx cant't.
View 5 Replies
View Related
Nov 20, 2012
i want to give my switch a ip address with same subnet as a pc which is for eg having ip address of class a and subnet of 255.255.240.0
View 4 Replies
View Related
