I am new to VLANs and Cisco SMB switches. I have a new SGE 2010P switch and i am trying to configure different VLANs, one for data, one for Voice and the other for server.
Is there any tutorial on how to configure VLAN, by the way i tried to used the web interface and admin guide, it totally confused my understanding of Vlans.
I want to implement SPAN or RSPAN of a vlan. Can this be done with the SGE2010P? I can't find the configuration guide on the Cisco Web Site.
View 1 Replies View RelatedI have configured 2 Vlans on the network. 1 - native Untagged for data traffic and 100 Tagged for VoIP.I have 4 SGE2010p switches 2- of them in stack working in L3 mode and 2 connected to the stack via single ethernet links in L2 mode.I have IP phones with trunked ports -Vlan100 tagged and 1 untagged. I have set CoS 5 for Voice Vlan 100 on the phones and CoS 5 to queue 3 mapping (in basic mode) on all switches.But it seems to not work at all.Should I use Advanced QoS mode?Where Can I find some QoS configuration example for Voice Vlan on SGE2010p switches?
View 1 Replies View RelatedI just purchased two Cisco switches (SGE2010P) for the new Mitel 5000 Phone System. The Mitel vendor programmed and setup the phone system for us, but they couldn’t figure out the VLAN setup on the my switch. So now I have everything on one network and I am stuck on my own to figure the VLAN on my own. So please, some step by step on the settings on the switches, the router and the server (DHCP).
Here is what I have now:
2 floors building with a Cisco SGE2010P switch for each floor.Sonicwall TZ 210 routerWindows 2008 R2 server for DHCPMitel 5000I have the switch on Layer 2 at this moment, but I can switch it to Layer 3 if that makes the process easier and less steps.My network as follows: Router: 192.168.123.254Windows Server: 192.168.123.9Switches: 192.168.123.5 and 192.168.123.6Mitel 5000 server: 192.168.123.7 (has to be changed)The PCs are connected to the phones.
Just got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected. It's new for me as the previous Job i was sorking with a ws-3750-48.
i did from console change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out.. i need to reboot the switch..
We are upgrading out internal office network. I have setup 4 switches and 1 router using the following config.
-2 SGE2010p's are stacked together forming vlan 30 (to be used for phones)
-2 SGE2010's stacked for workstation's under vlan 20
Both switches are apart of vlan 1 (the default)Ports 1 on each stack are connected to a Cisco 890 (port fe2 and fe3) in trunk mode. Ports 2 and 3 are in an LAG group and connected to the neighboring stack (I have attached a diagram), and are also in trunk mode).At this point one port (port 1 on either stack) goes into blocking mode, and I get why ,it's a physical loop.I need more than a 100mb link between switches (which is what pulling the LAG between switches gets me), but I don't want to route phone traffic through my workstation switches to get out of the LAN.Is it possible using these switches and router to have a LAG between stacks and a link to the router for traffic to 0.0.0.0 ?
I have SGE2010 switches and I want to implement Multiple VLANs. Im a newbie and starting to study VLANS's.
I want to implement 5 VLAN's on my test lab network and here as follows:
192.168.1.x default
192.168.2.x
192.168.3.x
192.168.20.x
192.168.100.x
The .1 is exclusively for my test-lab servers.
The .2 is general test-lab Win-XP workstations.
The .3 is general test-lab Win7 worstations
The .20 is general test-lab production worstations
The .100 is for test-lab IP PHONES.
How many watts do the Cisco SGE2010P 48 POE switches draw?
View 1 Replies View RelatedI'm the administrator of a system composed of seven SGE2010P switches in stack configuration.I developed a script to update the ACL at regular time intervals.
ACLs work well unless one or more switches in the stack is turned off. In this case it would seem that once, which switches off will restart, they do not synchronize ACLs assigned to interfaces.
Currently the only solution I've found to restore functionality, it is cold restart of the entire stack.I was wondering if there is a command to propagate the acl switches that I can recall in the event of a restart of any of these.
I have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
I recently changed jobs and am now supporting a small(but rapidly growing) environment as follows:
35 PoE phones with a switchport going to a workstation
8 PoE cameras
7 servers(2 NICs each with link aggregation)
Various racked network hardware
I currently have an Enterasys 10/100 48p PoE switch powering all of the PoE devices, but the switch is getting old and I'd like to start converting over to pure gigabit. There's also an HP Procurve 2810-48G that all of the servers and other racked network hardware are plugged into. That switch is fine, but doesn't have PoE, so its uses are limited to the rack.
Just a few other things to keep in mind... Whomever setup this network failed to separate the voice and data traffic into their own VLANs + QoS, so that needs to be done as well. Expandability is key as the company is growing at a rapid pace- Stacking is certainly desirable, but not an absolute requirement.
I'd like to keep the price point bellow $2000 if I can get a good product. Cisco would be cool, but the price point is way too high for the features that I need. Any great recommendations? Here's some that I've been looking at:
Cisco SGE2010P
Netgear GS748TPS
I have a Cisco Calayst C3560G core switch with 4 x SGE2010P Switches which are invidually linked/trunked via 2x CAT6 Cables for each SGE switch so im not stacking them. First problem is i cant seem to trunk/bond the 2 cables to the SGE LAGs i created, I can only use 1 cable per SGE switch. Yes the Core switch is configured correctly and have the proper Port Channel config (below is an example of a config) how do i get this working!?
I run POE Voip phones and PC's of 1 cable that is vlan'd on the phones, so each port on the SGE's are trunk'd
CISCO C3560G
interface Port-channel1
switchport trunk encapsulation dot1q
switchport mode trunk
[code]...
The other issue and more troublesome is that I have random reboots on all of the SGE's the LOGs tell me nothing! I cant seem to figure it out even had the units swapped out! Jumbo Frames are enabled but still happens even if disabled. Got some STP/RSTP settings but nothing works.
SGE Hardware Version 00.00.01
SGE Software Version 3.0.018
SGE Boot Version 2.0.0.03
I have configured stack with 2 sge2010p switches. I want to connect this stack to the HP procurve switch using port agregation (LAG) technique. I want to use one ge port on each sge switch.How to configure it? Will it work witch port agregation on procurve?
View 2 Replies View RelatedI've got multiple SGE2000P & SGE2010P switches
Originally I was happy just set them all up in a stacked ring configuration. However I've become aware that my back bone fibre links are contantly pushed to their max.
So I've decided that I should change this configuration and unstack the switches and make them all stand-alone units. and I'll configure 2 cable LAG links between all my switches Theorically I should now get 2GIGs between each switch and to complete the ring in my network for redundancy I'll turn on Spanning tree.
However I've tested the speed and I just can not seem to get a LAG connection with 2 x 1gig cables to push more data than a single link 1gig link cable would.
My test enviroment(not using fibre optic cables just cat5e copper cabling):
4 x pc's(all gigabit network cards)
2 x sge2000p switches
PC1 ---(1G eth)--- /---(1G eth)--- PC2
[SGE2000P]===(LAG1 2x1G cables)===[SGE2000P]
PC3 ---(1G eth)---/ ---(1G eth)--- PC4
If I send files from PC1 & PC3 simultaneously to PC2 & PC4 They don't transfer faster than if I I just use a single 1GIG Link cable
looking at the LAG configuration it shows both cables are connected & the LAG looks like it's working. But it really doesn't seem to be running at the expected 2GIG?
The LAG fail over seems to work fine if I remove either of the 2 cables from the LAG the link continues to work. (sometimes it will drop a ping when removing or readding a LAG cable)
I currently have two SGE2010's with a 4-port LAG configured between them. I'm looking to add another two SGE2010's and I want to add redundancy at the same time. The switches are currently in standalone mode. I don't have fiber connectors and was planning on just using copper for the uplinks.
My questions are:
- Is it possible to use stack mode in conjunction with 4-port LAG groups to create redundant 4-port links between all of the switches? The documentation says that ports 24&48 are reserved for stacking - does that mean I can't specify a LAG instead?
- If 4-port LAGs aren't possible, does that mean that these switches max out at 1Gpbs uplinks if you use stack mode?
I've got a cisco asa 5520 and setting up the NAT for multiple DMZs on it.
I want to use PAT on the outside interface.
internally ive created subinterfaces for the VLANs and connected to a trunk port on a switch.
configure NAT for this scenario. I've got only 1 external public IP address.
Where can I find information on using debug on the SGE2010P switches? The information in the admin and reference guides is extermely limited.
View 1 Replies View RelatedI have switche SGE2010P, router 871 and 3 cisco ip phone 7920. If cisco ip phone 7920 connected to switche SGE2010P then link is down. But if cisco ip phone 7920 connected to router 871 then link is up. In the log switche SGE2010P is not event about this.Why are cisco ip phone 7920 not work with switche SGE2010P?
View 3 Replies View RelatedWhen I try to apply an ACL to a port on my SGE2010P, I get the following error:Can't bind acl/policy-map to an interface when the security suite is enabled in a per-port mode.I don't see an option where I can set the security suite mode.
View 10 Replies View RelatedI have configured the above switch with 2 vlans, with vlan interfaces and a default route that points to an internet router.
The switch is running in Layer 3 mode
================ ================
= = Vlan5 = =
= SGE2010 = ++++++++++++++ = Draytek = ------------------ INTERNET
= = = =
================ ================
192.168.0.254
Vlan 5 Data
Vlan 10 Voice
Int Vlan 5 192.168.0.253/24
Int vlan 10 192.168.10.253/24
0.0.0.0 0.0.0.0 192.168.0.254
The inter vlan routing works fine with the .253 addresses as the default gateway to the PC's but I cannot browse the internet.
When I change my gateway to the router .254 address, I get out on the internet fine.
I have just downloaded new software for sge2010p. I had tried to made an upgrade on some switches, but switches still boot with the old software.I have installed software 3.0.0.18 and boot 2.0.0.03. I have downloaded software 3.0.1 from cisco, put it on tftp and started an upgrade via switch web interface. I have checked that the active image is set to 1, and started the upgrade.Switch has downloaded soft from tftp, and reported that process has been finished without errors.After the restart switch have 3.0.0.18 software again. I have try to do this same on 4 different switches working in L3 and L2 mode - always with the same effect.Should I upgrade both images in the same time to get this work?
I have noticed, that the new firmware is located on image 2.
# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active*
[Code] ...
So I try to set active image via console command:
# boot system image-2
and again...
a# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active*
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active
"*" designates that the image was selected for the next boot
Finally i have tried to set the active image to "2" using console menu: I have set it like this:
Active Image
============
Unit ID Active Image Active Image after Reset
======= ============ ========================
1 Image 1 Image 2
and save..
[Code]
Where is the right place to set active image for 2. Is the "active image" settings only sets the firmware image which switch uses or configuration files too?
Recently our company purchased 3 Lynksys SGE2010p, At the moment they work as a stack but as we are implementing UCCX we need to mirror 15 ports but during the provisioning i've noticed that the limit is 8 ports per stack. I'm wondering whether this is a known issue or just a known limitation . I believe that most probably i'll need to move back to stand alone mode so i could configure 8 mirrored ports per switch.
View 2 Replies View RelatedCreated 2 separate VLANs on SGE2010P switch. Neither in Native VLAN 1.
For example;
-Port g01 in VLAN 56
-Port g25 in VLAN 56
-Port g10 in VLAN 10
-Port g37 in VLAN 10
All appears to work well within the respective VLAN (i.e. DHCP, ARP, etc. no IPs from other VLANs)STP - Spanning Tree is Globally disabled.
However; when I feed a n new network (which has STP enabled) into VLAN 10; I then plug a laptop with wireshark running into VLAN 56 - cannot see any other traffic/packet...except STP packets coming from a CISCO device on VLAN 10 while I am plugged into VLAN 56.
This demonstrates to me the network is not truely seperated. I know this because last night I crossed two networks and caused havoc; ouch.I configed a D-Link switch with the same scenario and no issue.
I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960?
class-map match-any VLAN50-51-52
match vlan 50-52
class-map match-any VLAN53
[Code].....
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies View RelatedWe recently purchased a SF 300-48P to replace a Layer 3 3Com switch that died. I've sucessfully put the switch into Layer 3 mode and assigned ip addresses to each of the VLANs but I cannot figure out how to implement routes for those. Here's some info on our network and what the previous switch had. [code]
Not sure if this can be translated into the Cisco or not.. If i try to create an IP route like these i get errors that the Gateway can be a route.
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
(eth ports routing only) and a layer 2 switch into a cluster of two layer 3 switch clustered. I have looked at Cisco 3550 EMIs with HSRP but I would like to implement based on newer models of Cisco switches.
View 6 Replies View RelatedI am trying to implement IP SLA. Can I implement it on layer2 switches?
View 5 Replies View RelatedHow to implement ipv6 on windows 7
View 1 Replies View RelatedHow can i implement networking in my THREE floor office by using routers and switches?
View 1 Replies View RelatedI have a SG300 Switche working in layer 3 mode.I configured 3 VLANs on the switch, assigned all ports, given IP addresses to VLANs interfaces, etc.Now I want to implement ACL to permit or deny access between vlans and hosts.Can I apply an ACL to a whole VLAN (in or out) like Catalyst models?I mean apply the ACL to the entire vlan or the only way in this model is to implement that ACL port by port?Every time I have a new port configure to work in a Vlan I have to implement the ACL?
View 4 Replies View RelatedI have a RV120W Firewall and I've created 3 Vlans. One for Internet Access Computers, One for non-Internet access, one for printers. How can I implement security to keep Internet and non-internet vlan computers from communicating with one anothers? Both computer vlans will need to communicate with printer
View 1 Replies View Related
