Cisco Switches :: Find Information On Using Debug On SGE2010P?
Sep 22, 2011Where can I find information on using debug on the SGE2010P switches? The information in the admin and reference guides is extermely limited.
View 1 Replies
ADVERTISEMENT
Cisco Switches :: How Many Watts Do SGE2010P 48 POE Switches Draw
Aug 8, 2012How many watts do the Cisco SGE2010P 48 POE switches draw?
View 1 Replies View RelatedCisco Switches :: Unable To Use ACL In SGE2010P Switches?
Apr 9, 2013I'm the administrator of a system composed of seven SGE2010P switches in stack configuration.I developed a script to update the ACL at regular time intervals.
ACLs work well unless one or more switches in the stack is turned off. In this case it would seem that once, which switches off will restart, they do not synchronize ACLs assigned to interfaces.
Currently the only solution I've found to restore functionality, it is cold restart of the entire stack.I was wondering if there is a command to propagate the acl switches that I can recall in the event of a restart of any of these.
Cisco SGE2010P - 48p Gigabit PoE Switches?
Jan 2, 2011I recently changed jobs and am now supporting a small(but rapidly growing) environment as follows:
35 PoE phones with a switchport going to a workstation
8 PoE cameras
7 servers(2 NICs each with link aggregation)
Various racked network hardware
I currently have an Enterasys 10/100 48p PoE switch powering all of the PoE devices, but the switch is getting old and I'd like to start converting over to pure gigabit. There's also an HP Procurve 2810-48G that all of the servers and other racked network hardware are plugged into. That switch is fine, but doesn't have PoE, so its uses are limited to the rack.
Just a few other things to keep in mind... Whomever setup this network failed to separate the voice and data traffic into their own VLANs + QoS, so that needs to be done as well. Expandability is key as the company is growing at a rapid pace- Stacking is certainly desirable, but not an absolute requirement.
I'd like to keep the price point bellow $2000 if I can get a good product. Cisco would be cool, but the price point is way too high for the features that I need. Any great recommendations? Here's some that I've been looking at:
Cisco SGE2010P
Netgear GS748TPS
Cisco Switches :: Using C3560G With 4x SGE2010P?
Feb 21, 2012I have a Cisco Calayst C3560G core switch with 4 x SGE2010P Switches which are invidually linked/trunked via 2x CAT6 Cables for each SGE switch so im not stacking them. First problem is i cant seem to trunk/bond the 2 cables to the SGE LAGs i created, I can only use 1 cable per SGE switch. Yes the Core switch is configured correctly and have the proper Port Channel config (below is an example of a config) how do i get this working!?
I run POE Voip phones and PC's of 1 cable that is vlan'd on the phones, so each port on the SGE's are trunk'd
CISCO C3560G
interface Port-channel1
switchport trunk encapsulation dot1q
switchport mode trunk
[code]...
The other issue and more troublesome is that I have random reboots on all of the SGE's the LOGs tell me nothing! I cant seem to figure it out even had the units swapped out! Jumbo Frames are enabled but still happens even if disabled. Got some STP/RSTP settings but nothing works.
SGE Hardware Version 00.00.01
SGE Software Version 3.0.018
SGE Boot Version 2.0.0.03
Cisco Switches :: Sge2010p Lag To HP Procurve Switch
Jul 18, 2011I have configured stack with 2 sge2010p switches. I want to connect this stack to the HP procurve switch using port agregation (LAG) technique. I want to use one ge port on each sge switch.How to configure it? Will it work witch port agregation on procurve?
View 2 Replies View RelatedCisco Switches :: Sge2010p (v5) - How To Set QoS For VoIP Vlan
Jul 24, 2011I have configured 2 Vlans on the network. 1 - native Untagged for data traffic and 100 Tagged for VoIP.I have 4 SGE2010p switches 2- of them in stack working in L3 mode and 2 connected to the stack via single ethernet links in L2 mode.I have IP phones with trunked ports -Vlan100 tagged and 1 untagged. I have set CoS 5 for Voice Vlan 100 on the phones and CoS 5 to queue 3 mapping (in basic mode) on all switches.But it seems to not work at all.Should I use Advanced QoS mode?Where Can I find some QoS configuration example for Voice Vlan on SGE2010p switches?
View 1 Replies View RelatedCisco Switches :: SGE2010P And SGE2000P LAG Configuration
Sep 19, 2011I've got multiple SGE2000P & SGE2010P switches
Originally I was happy just set them all up in a stacked ring configuration. However I've become aware that my back bone fibre links are contantly pushed to their max.
So I've decided that I should change this configuration and unstack the switches and make them all stand-alone units. and I'll configure 2 cable LAG links between all my switches Theorically I should now get 2GIGs between each switch and to complete the ring in my network for redundancy I'll turn on Spanning tree.
However I've tested the speed and I just can not seem to get a LAG connection with 2 x 1gig cables to push more data than a single link 1gig link cable would.
My test enviroment(not using fibre optic cables just cat5e copper cabling):
4 x pc's(all gigabit network cards)
2 x sge2000p switches
PC1 ---(1G eth)--- /---(1G eth)--- PC2
[SGE2000P]===(LAG1 2x1G cables)===[SGE2000P]
PC3 ---(1G eth)---/ ---(1G eth)--- PC4
If I send files from PC1 & PC3 simultaneously to PC2 & PC4 They don't transfer faster than if I I just use a single 1GIG Link cable
looking at the LAG configuration it shows both cables are connected & the LAG looks like it's working. But it really doesn't seem to be running at the expected 2GIG?
The LAG fail over seems to work fine if I remove either of the 2 cables from the LAG the link continues to work. (sometimes it will drop a ping when removing or readding a LAG cable)
Cisco Switches :: SGE2010P - VLan For VOIP?
Mar 11, 2012I just purchased two Cisco switches (SGE2010P) for the new Mitel 5000 Phone System. The Mitel vendor programmed and setup the phone system for us, but they couldn’t figure out the VLAN setup on the my switch. So now I have everything on one network and I am stuck on my own to figure the VLAN on my own. So please, some step by step on the settings on the switches, the router and the server (DHCP).
Here is what I have now:
2 floors building with a Cisco SGE2010P switch for each floor.Sonicwall TZ 210 routerWindows 2008 R2 server for DHCPMitel 5000I have the switch on Layer 2 at this moment, but I can switch it to Layer 3 if that makes the process easier and less steps.My network as follows: Router: 192.168.123.254Windows Server: 192.168.123.9Switches: 192.168.123.5 and 192.168.123.6Mitel 5000 server: 192.168.123.7 (has to be changed)The PCs are connected to the phones.
Cisco Switches :: IP Phone 7920 Not Work With SGE2010P
Mar 25, 2013I have switche SGE2010P, router 871 and 3 cisco ip phone 7920. If cisco ip phone 7920 connected to switche SGE2010P then link is down. But if cisco ip phone 7920 connected to router 871 then link is up. In the log switche SGE2010P is not event about this.Why are cisco ip phone 7920 not work with switche SGE2010P?
View 3 Replies View RelatedCisco Switches :: How To Implement Multiple VLAN On SGE2010P
Mar 7, 2012I am new to VLANs and Cisco SMB switches. I have a new SGE 2010P switch and i am trying to configure different VLANs, one for data, one for Voice and the other for server.
Is there any tutorial on how to configure VLAN, by the way i tried to used the web interface and admin guide, it totally confused my understanding of Vlans.
Cisco Switches :: SGE2010P Can't Bind ACL / Policy-map To Interface
Nov 15, 2012When I try to apply an ACL to a port on my SGE2010P, I get the following error:Can't bind acl/policy-map to an interface when the security suite is enabled in a per-port mode.I don't see an option where I can set the security suite mode.
View 10 Replies View RelatedCisco Switches :: Default Routing Not Working On SGE2010P
Nov 10, 2011I have configured the above switch with 2 vlans, with vlan interfaces and a default route that points to an internet router.
The switch is running in Layer 3 mode
================ ================
= = Vlan5 = =
= SGE2010 = ++++++++++++++ = Draytek = ------------------ INTERNET
= = = =
================ ================
192.168.0.254
Vlan 5 Data
Vlan 10 Voice
Int Vlan 5 192.168.0.253/24
Int vlan 10 192.168.10.253/24
0.0.0.0 0.0.0.0 192.168.0.254
The inter vlan routing works fine with the .253 addresses as the default gateway to the PC's but I cannot browse the internet.
When I change my gateway to the router .254 address, I get out on the internet fine.
Cisco Switches :: SGE2010P - Implement Span / RSPAN To A Vlan
May 1, 2012I want to implement SPAN or RSPAN of a vlan. Can this be done with the SGE2010P? I can't find the configuration guide on the Cisco Web Site.
View 1 Replies View RelatedCisco Switches :: Sge2010p Software Upgrade Switch Always Boots
Aug 6, 2011I have just downloaded new software for sge2010p. I had tried to made an upgrade on some switches, but switches still boot with the old software.I have installed software 3.0.0.18 and boot 2.0.0.03. I have downloaded software 3.0.1 from cisco, put it on tftp and started an upgrade via switch web interface. I have checked that the active image is set to 1, and started the upgrade.Switch has downloaded soft from tftp, and reported that process has been finished without errors.After the restart switch have 3.0.0.18 software again. I have try to do this same on 4 different switches working in L3 and L2 mode - always with the same effect.Should I upgrade both images in the same time to get this work?
I have noticed, that the new firmware is located on image 2.
# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active*
[Code] ...
So I try to set active image via console command:
# boot system image-2
and again...
a# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active*
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active
"*" designates that the image was selected for the next boot
Finally i have tried to set the active image to "2" using console menu: I have set it like this:
Active Image
============
Unit ID Active Image Active Image after Reset
======= ============ ========================
1 Image 1 Image 2
and save..
[Code]
Where is the right place to set active image for 2. Is the "active image" settings only sets the firmware image which switch uses or configuration files too?
Cisco Switches :: SGE2010p / Configure Vlan To Reach Few Subnet?
Jun 9, 2010Just got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected. It's new for me as the previous Job i was sorking with a ws-3750-48.
i did from console change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out.. i need to reboot the switch..
Cisco Switches :: Port Mirroring Limit Of 8 Ports On SGE2010P
Jan 24, 2013Recently our company purchased 3 Lynksys SGE2010p, At the moment they work as a stack but as we are implementing UCCX we need to mirror 15 ports but during the provisioning i've noticed that the limit is 8 ports per stack. I'm wondering whether this is a known issue or just a known limitation . I believe that most probably i'll need to move back to stand alone mode so i could configure 8 mirrored ports per switch.
View 2 Replies View RelatedCisco Switches :: Created 2 Separate VLANs On SGE2010P Switch
Jun 21, 2012Created 2 separate VLANs on SGE2010P switch. Neither in Native VLAN 1.
For example;
-Port g01 in VLAN 56
-Port g25 in VLAN 56
-Port g10 in VLAN 10
-Port g37 in VLAN 10
All appears to work well within the respective VLAN (i.e. DHCP, ARP, etc. no IPs from other VLANs)STP - Spanning Tree is Globally disabled.
However; when I feed a n new network (which has STP enabled) into VLAN 10; I then plug a laptop with wireshark running into VLAN 56 - cannot see any other traffic/packet...except STP packets coming from a CISCO device on VLAN 10 while I am plugged into VLAN 56.
This demonstrates to me the network is not truely seperated. I know this because last night I crossed two networks and caused havoc; ouch.I configed a D-Link switch with the same scenario and no issue.
Cisco Switches :: SGE2010p VLAN Trunks Spanning Tree And A Port Blocked
Jul 21, 2012We are upgrading out internal office network. I have setup 4 switches and 1 router using the following config.
-2 SGE2010p's are stacked together forming vlan 30 (to be used for phones)
-2 SGE2010's stacked for workstation's under vlan 20
Both switches are apart of vlan 1 (the default)Ports 1 on each stack are connected to a Cisco 890 (port fe2 and fe3) in trunk mode. Ports 2 and 3 are in an LAG group and connected to the neighboring stack (I have attached a diagram), and are also in trunk mode).At this point one port (port 1 on either stack) goes into blocking mode, and I get why ,it's a physical loop.I need more than a 100mb link between switches (which is what pulling the LAG between switches gets me), but I don't want to route phone traffic through my workstation switches to get out of the LAN.Is it possible using these switches and router to have a LAG between stacks and a link to the router for traffic to 0.0.0.0 ?
Find Clearwires ISP Information To Set Up Older 2.4 Router?
May 19, 2012How do you find Clearwires ISP information to set up older 2.4 router?
View 1 Replies View RelatedCisco Infrastructure :: Network 3501 Series Could Not Find Information
Oct 2, 2011I am new in networking. All my knowledge is based on books and no real life experience. At my job I am required to set up the network and configure all apparatus I never worked before with.
We have regular cable internet in the office. Modem is connected to Apple router (time capsule). No trouble. Now we are getting fibre optic in the office. Mngmnt has abought the following Cisco stuff:
Cisco Wireless Controller 2504
Cisco 3501 AP 802.11g/n Ctrlr based AP
Cisco ASA 5510 Firewall appliance
Cisco Power Injector AP3500 Series
According to my understding, the fibre optic point will be connected to ASA which will be further connected to wireless controller and then access point.
I cant find the requird info. The guides available at cisco are for when you use CLI and as a beginner I prefer to use GUI. While trying to config ASA, there are many questions I can't find the answers.
Cisco WAN :: 3750X Stack Of 9 Switches Reload With No Information
Dec 13, 2011Recently, we had a 3750X stack of 9 switches reload with no information as to why. Our syslog server received no spurious errors regarding the cause nor did the location lose power. The UPS to which it is attached logged no glitches relating to power. Other cisco devices (router, other switches not in the stack) did not reload. No one was in the MDF during this time. We self insure these line of switches so a TAC case is not an option at this time. Any forensic tools that I could try in an attempt to narrow down the cause.
View 5 Replies View RelatedCisco Switches :: SF300-24 Snmp Get Mac-address Information Not Available?
Feb 21, 2013Im sitting with a few cisco sf-300 24 switches and i'm trying to get the Mac-addresses the switch have learned from each computer connected to the switch.
View 2 Replies View RelatedCisco Switches :: Does Sge 2010 Support Routing Information Protocol (RIP)
Dec 27, 2011if the sge2010 switch support Routing Information Protocol (RIP) and if so how do I enable it. I have a small wireless router that support it and would like client connected on it te bo visible from the wan side and that worked when I had another device doing the routing with RIP support the wireless router was picking up that information and the routing for the wireless client was working.
View 2 Replies View RelatedCisco Switches :: SG300 Simple GVRP / Propagate VLAN Information From One To Other?
Aug 10, 2012I have 2 SG300 switches and all I want is to propagate VLAN info from one to other. I do not have computers with GVRP compliant NICs, so I dont want that auto registeration functionality on access ports. I want VLAN prop via trunks and switchport mode access on access ports just like VTP. I have read on cisco docs that this functionality is provided with GVRP Mode fixed, but there are only 2 modes that I can see on SG300 are Normal and Forbidden. Trunk configured correctly, gvrp is enabled globally and on port, ports are up and functional, tried different combinations of checking and unchecking boxes of dynmic vlan creation and enable registeration on both ends but no joy. When I create a vlan from one, it doesnt propogate to other.
View 1 Replies View RelatedCisco Switching/Routing :: VLAN Information Not Propagating Between Nexus 5K Switches?
Oct 2, 2012I have 2 NEXUS switches in VPC. When I create/delete a VLAN gets updated in the same switch, but the VLAN information does not get propagated to the neighboring switch. Revision number remains the same even if I modify the VLAN. Had also tried changing the VTP status to transparent mode & reverting it to client mode but no luck.Have double confirmed on the VTP domain names & password. However the same setup in different location which works perfectly fine.
View 1 Replies View Related3550 Find At Least Two More Switches
Jan 22, 2012I finished the CCNA and CCNP classes last year but due to wife/school/excuse I did'nt have time to buckle down and study for the tests. So since time is flying buy and I got my new desk set up I figured I would set my lab up and get cracking.
On top I have a a Pix 506 and a 1900 switch. I need to find at least two more switches, hopefully 3550's or something close.Then I have 5 2600's with an assortment of cards, but I would like to replace most of them to either WIC 2T or HWIC 2FE's.
Not shown on the bottom are 2 2500's that will be configured as Frame Relay switches. I have a 3600 sitting on my bench in the shop and I was hoping to get something I could configure as a terminal server as well. I have GNS3 on my lab box and was planning on getting another network card and tying it into the hardware lab.
Cisco WAN :: SGE2010P Won't Switch Respond To Login After Reboot
Apr 8, 2012SGE2010P won't Switch respond to login after reboot
View 1 Replies View RelatedCisco Switching/Routing :: How To Create Vlans On Sge2010p
Jun 18, 2012I just want create vlans on switch sge2010p
Scenario:
vlan10
ip address 192.168.10.254/24
vlan20
ipaddress 192.168.20.254/24
vlan10 needs internet.
I have a static ip internet which is 200.33.22.11 gateway: 200.33.22.10 I have a router configured working as gateway, It has ip 192.168.2.1.
I have configured two vlans. But when I try to check if vlan has internet, it doesn't work.
Cisco Switches :: SRW2024 - Cannot Find 1.0.0.86 Firmware
Jan 28, 2013I did not know to update the boot software of my SRW2024 first, then update to 1.2.2b.I need to go back to the 1.0.0.86 firmware.
Is it downloadable and will it work (ie work backwards and then do it properly)? I know how to use hyperterminal and the xmodem protocol if need be.
Cisco WAN :: 2900 Nothing Appear For ACL Debug
Mar 22, 2012i have 3 access-list configured IN | Out on my Border router (MARTIAN) ,i have to look which one block some of the traffic passing through ,for that matter i have enabled the below commands on my ISR 2900: with nothing output.
View 3 Replies View RelatedRouters / Switches :: Find The Wpa-psk For Wifi?
May 24, 2011how do you find a WPA-PSK for wifi from a laptop? (I forgot mine and cant get into my psp).
View 4 Replies View RelatedCisco Switching/Routing :: Assigning IP Address To VLANs In SGE2010P?
Apr 9, 2012Recently purchased 5 SGE2010P 48-port switches to replace older L2 switches. I have 4 switches in single stack and one as a standalone. Both the stack and standalone will connect to at least 1 Dell 2724 switch. Both the stack and the standalone Cisco are in Layer 3 mode.
I have created several VLans on the Cisco switches, and am trying to assign an IP address to the VLan, but cannot seem to figure out the web gui. Each time I try to use Systems > System Management > IP Addressing > IP Interface, then click Add, it simply changes the existing IP of the management interface. So, I'm not sure how to go about assigning an IP Address to an Vlan.