Cisco Switches :: SGE2010 / How To Implement Multiple VLANs
Jun 21, 2011
I have SGE2010 switches and I want to implement Multiple VLANs. Im a newbie and starting to study VLANS's.
I want to implement 5 VLAN's on my test lab network and here as follows:
192.168.1.x default
192.168.2.x
192.168.3.x
192.168.20.x
192.168.100.x
The .1 is exclusively for my test-lab servers.
The .2 is general test-lab Win-XP workstations.
The .3 is general test-lab Win7 worstations
The .20 is general test-lab production worstations
The .100 is for test-lab IP PHONES.
View 4 Replies
ADVERTISEMENT
Oct 31, 2012
I currently have two SGE2010's with a 4-port LAG configured between them. I'm looking to add another two SGE2010's and I want to add redundancy at the same time. The switches are currently in standalone mode. I don't have fiber connectors and was planning on just using copper for the uplinks.
My questions are:
- Is it possible to use stack mode in conjunction with 4-port LAG groups to create redundant 4-port links between all of the switches? The documentation says that ports 24&48 are reserved for stacking - does that mean I can't specify a LAG instead?
- If 4-port LAGs aren't possible, does that mean that these switches max out at 1Gpbs uplinks if you use stack mode?
View 4 Replies
View Related
Aug 20, 2012
I have 2 switch groups.
2 SGE2010's with VLAN's defined as 10,20 and 30
Vlan 10 is the management VLAN, and it uplinks to our border router.Vlan 20 is the workstation VLAN, and all workstations point to the switch as their default GW? Vlan 30 is the ip phone VLAN, and all phones use this as their gateway.
I would like to put a LAG between said switches, we have some servers on the ip phone switch that need to be accessed by the workstation clients, and the single 100mb link through the router is probably not going to be enough.As I understand it, because the switches have different networks on them, a simple lag will not work. I did create a lag, and assign ip addresses to each side, however in that mode, it doesn't appear I can block vlan 10 from transiting the LAG, and with out that block I will end up with a logical loop, and spanning-tree will block one of the uplinks, or the LAG itself.
View 10 Replies
View Related
Apr 4, 2011
I've got a cisco asa 5520 and setting up the NAT for multiple DMZs on it.
I want to use PAT on the outside interface.
internally ive created subinterfaces for the VLANs and connected to a trunk port on a switch.
configure NAT for this scenario. I've got only 1 external public IP address.
View 1 Replies
View Related
Dec 10, 2012
Id like to set up our AP to push our different vlans depending on which ESSID you connect to.
A few things I am unclear on. The switch port on the SGE needs to be in trunk mode I assume.
Do I marry the Management Vlan ID on the AP to the PVID on the SGE port ? Or is the PVID the untagged vlan ID ?
I set the switches port to trunk mode, it's PVID to 10 and set the management vlan ID on the AP to 10 and I get TTL Exceeded in Route when I try to ping.
View 1 Replies
View Related
Mar 25, 2012
I have a SG300 Switche working in layer 3 mode.I configured 3 VLANs on the switch, assigned all ports, given IP addresses to VLANs interfaces, etc.Now I want to implement ACL to permit or deny access between vlans and hosts.Can I apply an ACL to a whole VLAN (in or out) like Catalyst models?I mean apply the ACL to the entire vlan or the only way in this model is to implement that ACL port by port?Every time I have a new port configure to work in a Vlan I have to implement the ACL?
View 4 Replies
View Related
Mar 7, 2012
I am new to VLANs and Cisco SMB switches. I have a new SGE 2010P switch and i am trying to configure different VLANs, one for data, one for Voice and the other for server.
Is there any tutorial on how to configure VLAN, by the way i tried to used the web interface and admin guide, it totally confused my understanding of Vlans.
View 5 Replies
View Related
Jul 17, 2012
I was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Aug 26, 2012
I have 2 SG300-10 switches, and I need two VLANs, one for internal network and one for WiFi APs.I need ports 1->4 on both switches to be part of 1st VLAN and ports 5->8 on 2nd VLAN; and port 10 uplink to 2nd switch.How I set up the VLANs and interface VLAN mode?
[code]...
View 1 Replies
View Related
Jun 22, 2011
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
View 10 Replies
View Related
Aug 19, 2012
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
[code]...
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration?
View 14 Replies
View Related
Jun 26, 2012
I can't figure out how to configure a port membership with multiple VLANs. My setup:
- VLAN10
- VLAN20
- port settings tab: port24 in general mode
- ports to VLANs tab: untagged everywhere, when I set port 24 membership to VLAN10 I can't set port 24 membership in VLAN20 because when I do that port 24 membership in VLAN10 dissapears and vice versa
- but I can set port 24 membership to both VLANs in VLANs to port tab, but I think it doesn't work because:
- when I connect hosts to ports 23 (port 23 is a member of VLAN10 only) and 24 (member of VLAN10 and VLAN20)
there are not any connectivity between them
- but connectivity is working when I set the same PVID for both ports 23 and 24 in port setting tab, I can't set multiple PVID in here.
So, is it possible to configure port membership for multiple VLANs on this linksys. [URL]
View 1 Replies
View Related
Aug 30, 2011
I have 8 apartments that have a single internet connection coming into the building, I then have a PoE Access Point in each of the 8x apartments.
What I would like to be able to do is to have each apartment within its own vlan, but to be able to use the internet via one of the non-PoE ports (port 9 say) but do not want residents in different flats to be able to see each others devices on the same network.
I have a Cisco SG 300-10MP which has 8x PoE ports and 2x Ethernet ports, one of which my Internet connection is plugged into (using WiMax).
View 2 Replies
View Related
Mar 28, 2012
We have a Cisco 887 router and a Cisco SG-200 switch.We'd like to setup trunking between these 2 devices for multiple VLANs on the switch to be made available on the router.
With previous routers, you could set the router up in the configuration 'router-on-a-stick' and VLANs worked like a charm but the 887 no longer support sub-interfaces.So how can you get trunking working between the 2 devices?
Is there a VTP configuration menu for the SG-200 which we can setup in order for it to talk 'VTP' with the 887 router??
View 1 Replies
View Related
Nov 17, 2011
We have been set the task of securing a small managed office system which is currently set up with a standard switch allowing each of the offices (containing different companies) to see each other, and in some cases, access each others documents across the network.
Obviously this is a far from adequate set up and our aim is to isolate each office using VLAN's but share a common internet connection provided by the managed offices. We have two Cisco SGE2000-G5 layer 3 switches but we are new to Cisco equipment and VLAN's so we are not quite sure on how to implement this. DHCP would need to be provided by a Router, there is no Server. We are open to suggestions on the Router as we have yet to purchase one.
View 10 Replies
View Related
Nov 11, 2012
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
View 7 Replies
View Related
Jul 15, 2012
We have a SGE2010 48 port POE switch and need to share a printer with a subtennant. We do not want to give them access to any other resources.
Our LAN is 192.168.17.0/24 - the printer is at 192.168.17.50
The sub-tennats LAN is 10.0.1.0/24.
I belive I need to setup 3 VLANs -
10 - Us
20 - Subtennant
30 - Printer.
Is this correct and if so, how do we setup the VLANS?
View 3 Replies
View Related
Aug 13, 2011
I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
View 3 Replies
View Related
Feb 15, 2012
I looking to buy SGE 2010 swith, but I have some question:
1. Can I use 4 SFP ports and stack of two switches at the same time.
2. Is it possible to use for stacking ports other than 24, 48?
3. What is maximum possible number of ports to use for stacking (can I get more than 1Gb thruput).
View 0 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Aug 30, 2011
I am working on two SGE 2010 stacked and in routing mode. Everything work fine but before finishing the job, I wanted to lockdown all the network device so they would not be accessible from some subnets. Problem is, I cannot bind my ACLs to any interface. I get "Cannot apply because lack of HW resources." I am running firmware 3.0.0.18, and 3.0.1 release notes don't address that issue. TCAM utilization is at 3% Routing resources shows host: 200, routes:60, ip interfaces: 50 I have tried from the cli and get the same message.
View 3 Replies
View Related
Jun 28, 2012
Can I create lag betwen stack unit to increase speed between units ?? stack connection is only 1Gbit on ports 24/48 if posible lag link must be in trunk mode ?
View 4 Replies
View Related
Aug 29, 2011
Is there any issues with accessing the browser based GUI using Windows 7 64bit on a SGE2010 switch? I took the switch home and tried on my XP 32bit machine and works fine, but no luck on any windows 7 64bit pc's. I have tried 3 different new pc's on this new switch and no luck at all.
View 2 Replies
View Related
May 28, 2013
We have a single SGE2010 in layer 3 mode switch with a Server 2008 DHCP server.
We will be implimenting a Voip netowork where the PC's connect to the voip phone. I would like to create another vlan - 10. I have created the vlan and assigned the IP on the swtich.
Routing seems to be working. I can ping both IP addresses of the switch on either vlan.
I cannot get DHCP working. In the SGE switch I have enabled DHCP Relay, enabled option 82, set my DHCP Interface as VLan1, and specified the DHCP servers IP address. On the ports I have set the port where the DHCP server connects to as a trunk port with Vlan 1 untagged and vlan 10 tagged. I have set the ports where the phones connect as a trunk port with vlan1 untagged and vlan 10 tagged.
View 1 Replies
View Related
Jul 1, 2011
We've have a 2 SGE2010-48 port, stacked. 4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working. Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).
View 3 Replies
View Related
May 20, 2013
I want to know how am i do to change the Vlan1`s IP address because the actual ip will be used in another vlan. Actually i haver 10 vlans in L3 mode (routing) implemented in it.
View 5 Replies
View Related
May 15, 2011
I have been trying, so far unsucessfully, to trigger backups to a TFTP server of our SGE201 switches. I have testesd TFTP backups via the web interface, and that does work. I need SNMP as I need a scriptable method to trgiger the backups on a regular schedule. I am running the SNMP query from a RedHat Linux server. So far I have the following query work out, but it is failing: [code] The error I am getting is generic, and the same query failed on multiple switches running Software Version 3.0.0.18. The switch is set with the community having full SNMP-admin access from the server's IP address.
View 3 Replies
View Related
Mar 7, 2013
I have 5 VLAN's setup in the sge2010. I have one port (uplink for the network) that I want everyone to see. But have separate VLAN's for different departments as to keep them all separate. Everytime i try and Untag that uplink port, i lose my untag in the original VLAN it was tagged in, and it changes to excluded.
View 13 Replies
View Related
Jul 28, 2011
We are experiencing bridge storms and network slow downs and we believe we have traced the issue down to users plugging a cat 5/6 cable between 2 ports on the wall both wired back to a SGE2010 switch.
So we did a test - we plugged a single short cat 6 cable between 2 ports on a SGE2010, our access switch. Suprisingly, even with STP enabled, the switch DID NOT block one of the ports and in a few minutes the ENTIRE NETWORK was down, as CDP, STP, and ARP traffic became a multi-gigabit storm throughout the network.
Why on earth does this switch not block a port that is obviosly looped?
Every other cisco switch since I started on 1900XL's did this in 1999.
View 1 Replies
View Related
May 29, 2013
I am currently running two SGE2010 in stack and planning to purchase new Sg500 .I have two questions :
1. If these two different products can be managed as one stack.
2. Are the SFP (mini-GBIC) connections compatible and if so what accessories or parts do we need to enable them?
View 1 Replies
View Related
